홈 전원 관리 AC/DC & DC/DC converters (integrated FET)
홈
전원 관리
AC/DC & DC/DC converters (integrated FET)

TPS61070

활성

절전 모드를 지원하는 ThinSOT-23의 조정 가능 600mA 스위치, 1200kHz 부스트 컨버터

지금 주문
데이터시트

TPS61070

활성
데이터시트 지금 주문

제품 상세 정보

Vin (min) (V) 0.9 Vin (max) (V) 5.5 Topology Boost Type Converter Switching frequency (min) (kHz) 960 Switching frequency (max) (kHz) 1440 Features Load Disconnect, Synchronous Rectification Vout (min) (V) 1.8 Vout (max) (V) 5.5 Rating Catalog Operating temperature range (°C) -40 to 125 Iq (typ) (A) 0.000019
Vin (min) (V) 0.9 Vin (max) (V) 5.5 Topology Boost Type Converter Switching frequency (min) (kHz) 960 Switching frequency (max) (kHz) 1440 Features Load Disconnect, Synchronous Rectification Vout (min) (V) 1.8 Vout (max) (V) 5.5 Rating Catalog Operating temperature range (°C) -40 to 125 Iq (typ) (A) 0.000019
SOT-23-THN (DDC) 6 8.12 mm² 2.9 x 2.8
  • 90% Efficient Synchronous Boost Converter
    • 75-mA Output Current at 3.3 V From 0.9-V
      Input
    • 150-mA Output Current at 3.3 V From 1.8-V
      Input
  • Device Quiescent Current: 19 µA (Typ)
  • Input Voltage Range: 0.9 V to 5.5 V
  • Adjustable Output Voltage Up to 5.5 V
  • Power-Save Mode Version Available for
    Improved Efficiency at Low Output Power
  • Load Disconnect During Shutdown
  • Overtemperature Protection
  • Small 6-Pin Thin SOT23 Package
  • 90% Efficient Synchronous Boost Converter
    • 75-mA Output Current at 3.3 V From 0.9-V
      Input
    • 150-mA Output Current at 3.3 V From 1.8-V
      Input
  • Device Quiescent Current: 19 µA (Typ)
  • Input Voltage Range: 0.9 V to 5.5 V
  • Adjustable Output Voltage Up to 5.5 V
  • Power-Save Mode Version Available for
    Improved Efficiency at Low Output Power
  • Load Disconnect During Shutdown
  • Overtemperature Protection
  • Small 6-Pin Thin SOT23 Package

The TPS6107x devices provide a power supply solution for products powered by either a one-cell, two-cell, or three-cell alkaline, NiCd or NiMH, or one-cell Li-ion or Li-polymer battery. Output currents can go as high as 75 mA while using a single-cell alkaline, and discharge it down to 0.9 V. It can also be used for generating 5 V at 200 mA from a 3.3-V rail or a Li-ion battery. The boost converter is based on a fixed frequency, pulse-width-modulation (PWM) controller using a synchronous rectifier to obtain maximum efficiency. At low load currents the TPS61070 and TPS61073 enter the power-save mode to maintain a high efficiency over a wide load current range. The power-save mode is disabled in the TPS61071 and TPS61072, forcing the converters to operate at a fixed switching frequency. The maximum peak current in the boost switch is typically limited to a value of 600 mA.

The TPS6107x output voltage is programmed by an external resistor divider. The converter can be disabled to minimize battery drain. During shutdown, the load is completely disconnected from the battery. The device is packaged in a 6-pin thin SOT23 package (DDC).

For all available packages, see the orderable addendum at the end of the datasheet.

The TPS6107x devices provide a power supply solution for products powered by either a one-cell, two-cell, or three-cell alkaline, NiCd or NiMH, or one-cell Li-ion or Li-polymer battery. Output currents can go as high as 75 mA while using a single-cell alkaline, and discharge it down to 0.9 V. It can also be used for generating 5 V at 200 mA from a 3.3-V rail or a Li-ion battery. The boost converter is based on a fixed frequency, pulse-width-modulation (PWM) controller using a synchronous rectifier to obtain maximum efficiency. At low load currents the TPS61070 and TPS61073 enter the power-save mode to maintain a high efficiency over a wide load current range. The power-save mode is disabled in the TPS61071 and TPS61072, forcing the converters to operate at a fixed switching frequency. The maximum peak current in the boost switch is typically limited to a value of 600 mA.

The TPS6107x output voltage is programmed by an external resistor divider. The converter can be disabled to minimize battery drain. During shutdown, the load is completely disconnected from the battery. The device is packaged in a 6-pin thin SOT23 package (DDC).

For all available packages, see the orderable addendum at the end of the datasheet.
open-in-new 기타 AC/DC & DC/DC converters (integrated FET) 찾기
다운로드 스크립트와 함께 비디오 보기 동영상

관심 가지실만한 유사 제품

open-in-new 대안 비교
비교 대상 장치와 동일한 기능을 지원하는 핀 대 핀
TLV61070A 활성 최저 입력 전압 0.5V의 5V 2A 부스트 컨버터 Higher current capability
TLV61220 활성 5uA Iq를 지원하는 0.7V 저입력 전압 스텝업 컨버터 TLV61220 has lower current limited and pass through mode when disabled
다른 핀 출력을 지원하지만 비교 대상 장치와 동일한 기능
TPS61033 활성 5V, 5A 부스트 컨버터(전원 양호, 출력 방전 및 PFM/PWM 제어 포함) 5A/1.5A valley switch current limit and SOT583 packge with size of 2.1 x 1.2mm

기술 문서

star =TI에서 선정한 이 제품의 인기 문서
검색된 결과가 없습니다. 검색어를 지우고 다시 시도하십시오.
모두 보기15
유형 직함 날짜
* Data sheet TPS6107x 90% Efficient Synchronous Boost Converter With 600-mA Switch datasheet (Rev. E) PDF | HTML 2015/03/25
Application note 스트컨버터의 전력계 기본 계산 (Rev. D) PDF | HTML 2022/11/21
Application note Performing Accurate PFM Mode Efficiency Measurements (Rev. A) 2018/12/11
Selection guide Power Management Guide 2018 (Rev. R) 2018/06/25
Application note Optimizing Transient Response of Internally Compensated DC-DC Converters (Rev. B) 2017/11/29
Application note Extending the Soft Start Time Without a Soft Start Pin (Rev. B) 2017/06/15
Application note Five Steps to a Good PCB Layout of the Boost Converter PDF | HTML 2016/05/03
Analog Design Journal Accurately measuring efficiency of ultralow-IQ devices 2014/01/22
Analog Design Journal 2Q 2012 Issue Analog Applications Journal 2012/04/26
Analog Design Journal Design considerations for a resistive feedback divider in a DC/DC converter 2012/04/26
Analog Design Journal IQ: What it is, what it isn’t, and how to use it 2011/06/17
Application note TPS61020 Boost Converter Start-Up and Precharge 2010/01/28
Application note Minimizing Ringing at the Switch Node of a Boost Converter 2006/09/15
Application note Reducing Output Ripple Voltage of TPS61070 2005/06/07
Application note Single-cell Battery Discharge Characteristics Using the TPS61070 Boost Converter 2004/08/24

설계 및 개발

추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.

평가 보드

TPS61070EVM-062 — TPS61070 평가 모듈

The TPS61070EVM-062 is an evaluation tool for the TPS61070 inductive step-up converter IC. The TPS61070 integrated boost converter can supply voltages up to 5.5V from an input of 0.9-V to 5.5-V and is packaged in a 6-pin thin SOT23. The TPS61070EVM-062 is set up to provide a 5-V output. By (...)

사용 설명서: PDF
TI.com에서 구매할 수 없습니다
시뮬레이션 모델

Unencrypted TPS61070 PSpice Transient Model Package (Rev. B)

SLVMB37B.ZIP (71 KB) - PSpice Model
다운로드
거버(Gerber) 파일

Gerber Files for TPS61070EVM

SLVC129.ZIP (86 KB)
다운로드
레퍼런스 디자인

TIDA-01236 — 무선 초음파 가스 누출 감지기에서 코인 셀 배터리 작동 시간을 늘리기 위한 레퍼런스 설계

This reference design demonstrates a low-power wireless sensor which detects gas leaks by analyzing the ultrasonic spectrum for particular signatures. The system is designed to operate from a single Li-Primary coin cell and communicate wirelessly to a base station, which removes all requirements (...)
Design guide: PDF
회로도: PDF
레퍼런스 디자인

PMP8523 — 5.0V @ 70mA 부스트 컨버터

This design is a boost converter which delivers an output voltage of 5.0V @ 70mA at an input of 3.3V. PMP8523 was designed to fit industrial applications.
Test report: PDF
패키지 핀 다운로드
SOT-23-THN (DDC) 6 옵션 보기
TI의 평가 항목에 대한 표준 약관이 적용됩니다.

주문 및 품질

포함된 정보:
  • RoHS
  • REACH
  • 디바이스 마킹
  • 납 마감/볼 재질
  • MSL 등급/피크 리플로우
  • MTBF/FIT 예측
  • 물질 성분
  • 인증 요약
  • 지속적인 신뢰성 모니터링
포함된 정보:
  • 팹 위치
  • 조립 위치

지원 및 교육

TI 엔지니어의 기술 지원을 받을 수 있는 TI E2E™ 포럼

포럼 주제 모두 보기(영문)

콘텐츠는 TI 및 커뮤니티 기고자에 의해 "있는 그대로" 제공되며 TI의 사양으로 간주되지 않습니다. 사용 약관을 참조하십시오.

품질, 패키징, TI에서 주문하는 데 대한 질문이 있다면 TI 지원을 방문하세요. ​​​​​​​​​​​​​​

동영상