UCC27532
- Low Cost Gate Driver (offering optimal solution for driving
FET and IGBTs) - Superior Replacement to Discrete Transistor Pair Drive (providing
easy interface with controller) - CMOS Compatible Input Logic Threshold (becomes fixed at VDD above 18 V)
- Split Outputs Allow Separate Turn-On and Turn-Off Tuning
- Enable with Fixed TTL Compatible Threshold
- High 2.5-A Source and 5-A Sink Peak Drive Currents at 18-V VDD
- Wide VDD Range From 10 V up to 35 V
- Input Pins Capable of Withstanding up to -5-V DC Below Ground
- Output Held Low When Inputs are Floating or During VDD UVLO
- Fast Propagation Delays (17-ns typical)
- Fast Rise and Fall Times
(15-ns and 7-ns typical with 1800-pF Load) - Under Voltage Lockout (UVLO)
- Used as a High-Side or Low-Side Driver (if designed with
proper bias and signal isolation) - Low Cost, Space Saving 6-Pin DBV (SOT-23) Package
- Operating Temperature Range of –40°C to 140°C
The UCC27532 is a single-channel, high-speed, gate driver capable of effectively driving MOSFET and IGBT power switches by up to 2.5-A source and 5-A sink (asymmetrical drive) peak current. Strong sink capability in asymmetrical drive boosts immunity against parasitic Miller turn-on effect. The UCC27532 device also features a split-output configuration where the gate-drive current is sourced through OUTH pin and sunk through OUTL pin. This pin arrangement allows the user to apply independent turn-on and turn-off resistors to the OUTH and OUTL pins respectively and easily control the switching slew rates.
The driver has rail-to-rail drive capability and extremely small propagation delay typically 17 ns.
The UCC27532DBV has CMOS input threshold centered 55% rise and 45% fall in regards of VDD at VDD below or equal 18 V. When VDD is above 18 V, the input threshold remains fixed at its maximum level.
The driver has EN pin with fixed TTL compatible threshold. EN is internally pulled up; pulling EN low disables driver, while leaving it open provides normal operation. The EN pin can be used as an additional input with the same performance as the IN pin.
Leaving the input pin of driver open holds the output low. The logic behavior of the driver is shown in the application diagram, timing diagram and input and output logic truth table.
Internal circuitry on VDD pin provides an under voltage lockout function that holds output low until VDD supply voltage is within operating range.
The UCC27532 driver is offered in a 6-pin standard SOT-23 (DBV) package. The device operates over wide temperature range of 40°C to 140°C.
기술 문서
유형 | 직함 | 날짜 | ||
---|---|---|---|---|
* | Data sheet | 2.5-A and 5 A, 35-Vmax VDD FET and IGBT Single Gate-Driver with CMOS Input datasheet | 2013/02/05 | |
Application note | Using a Single-Output Gate-Driver for High-Side or Low-Side Drive (Rev. B) | PDF | HTML | 2023/09/08 | |
Application brief | External Gate Resistor Selection Guide (Rev. A) | 2020/02/28 | ||
Application brief | Understanding Peak IOH and IOL Currents (Rev. A) | 2020/02/28 | ||
Application brief | Implementing a Bipolar Gate Drive for Low-Side IGBTs and SiC FETs in Motor Drive | 2019/10/10 | ||
More literature | Fundamentals of MOSFET and IGBT Gate Driver Circuits (Replaces SLUP169) (Rev. A) | 2018/10/29 | ||
Selection guide | Power Management Guide 2018 (Rev. R) | 2018/06/25 | ||
Application note | UCC27531 35-V Gate Driver for SiC MOSFET Applications (Rev. A) | 2018/05/08 | ||
Application brief | Low-Side Gate Drivers With UVLO Versus BJT Totem-Pole | 2018/03/16 | ||
EVM User's guide | Using the UCC27532EVM-538 (Rev. A) | 2013/08/22 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
UCC27531EVM-184 — UCC27531 평가 모듈
PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®
TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 (...)
PMP11303 — 고효율 350W AC/DC 전원 공급 장치 레퍼런스 디자인
PMP30192 — 콤보 IC를 지원하는 범용 입력, 360W PFC+LLC 레퍼런스 설계
패키지 | 핀 | 다운로드 |
---|---|---|
SOT-23 (DBV) | 6 | 옵션 보기 |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.