TMS320VC5402

Name: TMS320VC5402
Brand: TI
SKU: TMS320VC5402
Price: 6.513 USD

現行

數位訊號處理器

立即訂購

產品規格表

document-pdfAcrobat TMS320VC5402 Fixed-Point Digital Signal Processor datasheet (Rev. G) (英文)

勘誤表

document-pdfAcrobat
TMS320UC5402/TMS320VC5402 Digital Signal Processors Silicon Errata (Rev. D) (英文)

TMS320VC5402

現行

產品規格表

立即訂購

產品詳細資料

DSP type

1 C54x

DSP (max) (MHz)

100

CPU

16-bit

Operating system

DSP/BIOS

Rating

Catalog

Operating temperature range (°C)

0 to 0

DSP type

1 C54x

DSP (max) (MHz)

100

CPU

16-bit

Operating system

DSP/BIOS

Rating

Catalog

Operating temperature range (°C)

0 to 0

LQFP (PGE)

144

484 mm² 22 x 22

Advanced Multibus Architecture With Three Separate 16-Bit Data Memory Buses and One Program Memory Bus
40-Bit Arithmetic Logic Unit (ALU), Including a 40-Bit Barrel Shifter and Two Independent 40-Bit Accumulators
17-× 17-Bit Parallel Multiplier Coupled to a 40-Bit Dedicated Adder for Non-Pipelined Single-Cycle Multiply/Accumulate (MAC) Operation
Compare, Select, and Store Unit (CSSU) for the Add/Compare Selection of the Viterbi Operator
Exponent Encoder to Compute an Exponent Value of a 40-Bit Accumulator Value in a Single Cycle
Two Address Generators With Eight Auxiliary Registers and Two Auxiliary Register Arithmetic Units (ARAUs)
Data Bus With a Bus-Holder Feature
Extended Addressing Mode for 1M × 16-Bit Maximum Addressable External Program Space
4K x 16-Bit On-Chip ROM
16K x 16-Bit Dual-Access On-Chip RAM
Single-Instruction-Repeat and Block-Repeat Operations for Program Code
Block-Memory-Move Instructions for Efficient Program and Data Management
Instructions With a 32-Bit Long Word Operand
Instructions With Two- or Three-Operand Reads
Arithmetic Instructions With Parallel Store and Parallel Load
Conditional Store Instructions
Fast Return From Interrupt
On-Chip Peripherals
- Software-Programmable Wait-State Generator and Programmable Bank Switching
- On-Chip Phase-Locked Loop (PLL) Clock Generator With Internal Oscillator or External Clock Source
- Two Multichannel Buffered Serial Ports (McBSPs)
- Enhanced 8-Bit Parallel Host-Port Interface (HPI8)
- Two 16-Bit Timers
- Six-Channel Direct Memory Access (DMA) Controller
Power Consumption Control With IDLE1, IDLE2, and IDLE3 Instructions With Power-Down Modes
CLKOUT Off Control to Disable CLKOUT
On-Chip Scan-Based Emulation Logic, IEEE Std 1149.1 (JTAG) Boundary Scan Logic
10-ns Single-Cycle Fixed-Point Instruction Execution Time (100 MIPS) for 3.3-V Power Supply (1.8-V Core)
Available in a 144-Pin Plastic Low-Profile Quad Flatpack (LQFP) (PGE Suffix) and a 144-Pin Ball Grid Array (BGA) (GGU Suffix)

All trademarks are the property of their respective owners.
IEEE Standard 1149.1-1990 Standard-Test-Access Port and Boundary Scan Architecture.
NOTE:This data sheet is designed to be used in conjunction with the TMS320C5000 DSP Family Functional Overview (literature number SPRU307).

Advanced Multibus Architecture With Three Separate 16-Bit Data Memory Buses and One Program Memory Bus
40-Bit Arithmetic Logic Unit (ALU), Including a 40-Bit Barrel Shifter and Two Independent 40-Bit Accumulators
17-× 17-Bit Parallel Multiplier Coupled to a 40-Bit Dedicated Adder for Non-Pipelined Single-Cycle Multiply/Accumulate (MAC) Operation
Compare, Select, and Store Unit (CSSU) for the Add/Compare Selection of the Viterbi Operator
Exponent Encoder to Compute an Exponent Value of a 40-Bit Accumulator Value in a Single Cycle
Two Address Generators With Eight Auxiliary Registers and Two Auxiliary Register Arithmetic Units (ARAUs)
Data Bus With a Bus-Holder Feature
Extended Addressing Mode for 1M × 16-Bit Maximum Addressable External Program Space
4K x 16-Bit On-Chip ROM
16K x 16-Bit Dual-Access On-Chip RAM
Single-Instruction-Repeat and Block-Repeat Operations for Program Code
Block-Memory-Move Instructions for Efficient Program and Data Management
Instructions With a 32-Bit Long Word Operand
Instructions With Two- or Three-Operand Reads
Arithmetic Instructions With Parallel Store and Parallel Load
Conditional Store Instructions
Fast Return From Interrupt
On-Chip Peripherals
- Software-Programmable Wait-State Generator and Programmable Bank Switching
- On-Chip Phase-Locked Loop (PLL) Clock Generator With Internal Oscillator or External Clock Source
- Two Multichannel Buffered Serial Ports (McBSPs)
- Enhanced 8-Bit Parallel Host-Port Interface (HPI8)
- Two 16-Bit Timers
- Six-Channel Direct Memory Access (DMA) Controller
Power Consumption Control With IDLE1, IDLE2, and IDLE3 Instructions With Power-Down Modes
CLKOUT Off Control to Disable CLKOUT
On-Chip Scan-Based Emulation Logic, IEEE Std 1149.1 (JTAG) Boundary Scan Logic
10-ns Single-Cycle Fixed-Point Instruction Execution Time (100 MIPS) for 3.3-V Power Supply (1.8-V Core)
Available in a 144-Pin Plastic Low-Profile Quad Flatpack (LQFP) (PGE Suffix) and a 144-Pin Ball Grid Array (BGA) (GGU Suffix)

All trademarks are the property of their respective owners.
IEEE Standard 1149.1-1990 Standard-Test-Access Port and Boundary Scan Architecture.
NOTE:This data sheet is designed to be used in conjunction with the TMS320C5000 DSP Family Functional Overview (literature number SPRU307).

The TMS320VC5402 fixed-point, digital signal processor (DSP) (hereafter referred to as the '5402 unless otherwise specified) is based on an advanced modified Harvard architecture that has one program memory bus and three data memory buses. This processor provides an arithmetic logic unit (ALU) with a high degree of parallelism, application-specific hardware logic, on-chip memory, and additional on-chip peripherals. The basis of the operational flexibility and speed of this DSP is a highly specialized instruction set.

Separate program and data spaces allow simultaneous access to program instructions and data, providing the high degree of parallelism. Two read operations and one write operation can be performed in a single cycle. Instructions with parallel store and application-specific instructions can fully utilize this architecture. In addition, data can be transferred between data and program spaces. Such parallelism supports a powerful set of arithmetic, logic, and bit-manipulation operations that can be performed in a single machine cycle. In addition, the '5402 includes the control mechanisms to manage interrupts, repeated operations, and function calls.

The TMS320VC5402 fixed-point, digital signal processor (DSP) (hereafter referred to as the '5402 unless otherwise specified) is based on an advanced modified Harvard architecture that has one program memory bus and three data memory buses. This processor provides an arithmetic logic unit (ALU) with a high degree of parallelism, application-specific hardware logic, on-chip memory, and additional on-chip peripherals. The basis of the operational flexibility and speed of this DSP is a highly specialized instruction set.

Separate program and data spaces allow simultaneous access to program instructions and data, providing the high degree of parallelism. Two read operations and one write operation can be performed in a single cycle. Instructions with parallel store and application-specific instructions can fully utilize this architecture. In addition, data can be transferred between data and program spaces. Such parallelism supports a powerful set of arithmetic, logic, and bit-manipulation operations that can be performed in a single machine cycle. In addition, the '5402 includes the control mechanisms to manage interrupts, repeated operations, and function calls.

open-in-new

尋找其它數位訊號處理器 (DSP)

下載觀看有字幕稿的影片影片

TI 不提供設計支援

此產品沒有 TI 針對新專案提供的持續設計支援，例如新內容或軟體更新。若有提供，您可在產品資料夾中找到相關資訊、軟體與工具。您也可以在 TI E2E^TM 支援論壇中搜尋封存的資訊。

技術文件

star

=TI 所選的此產品重要文件

找不到結果。請清除您的搜尋條件，然後再試一次。

檢視所有 14

	類型	標題	日期
*	Data sheet	TMS320VC5402 Fixed-Point Digital Signal Processor datasheet (Rev. G)	2008年 10月 20日
*	Errata	TMS320UC5402/TMS320VC5402 Digital Signal Processors Silicon Errata (Rev. D)	2003年 4月 10日
	Application note	TMS320VC5402 and TMS320UC5402 Bootloader (Rev. B)	2004年 11月 3日
	User guide	TMS320C54x Chip Support Library API Reference Guide (Rev. D)	2003年 5月 5日
	Application note	Using the TMS320C5402 DSK Sine Program and evmdsk54x.dll	2002年 11月 11日
	Application note	Interfacing the TLV320AIC12/13/14/15 Codec to the TMS320C5402? DSP	2002年 10月 24日
	Application note	Bootloading the TMS320VC5402 in HPI Mode	2002年 4月 29日
	User guide	TMS320C54x DSP CPU and Peripherals Reference Set Volume 1 (Rev. G)	2001年 3月 31日
	User guide	TMS320C54x DSP Algebraic Instruction Set Reference Set Volume 3 (Rev. C)	2001年 1月 31日
	User guide	TMS320C54x DSP Mnemonic Instruction Set Reference Set Volume 2 (Rev. C)	2001年 1月 31日
	Application note	Interfacing the TLV320AIC10/11 Codec to the TMS320C5402 DSP	2000年 12月 18日
	Application note	Powering the TMS320VC5402 DSP Using the TPS60100, TPS76918, and the TPS3305-18	1999年 12月 16日
	Application note	TPS6010x/TPS6011x Charge Pump (Rev. A)	1999年 12月 16日
	User guide	TMS320C54x DSP Applications Guide Reference Set Volume 4	1996年 10月 1日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

TMDSDSK5416 — TMS320C5416 DSP 入門套件 (DSK)

The TMS320C5416 DSP starter kit (DSK) is a low-cost development platform designed to speed the development of power-efficient applications based on TI's TMS320C54x DSPs. The kit, which provides new performance-enhancing features such as USB communications and true plug-and-play functionality, gives (...)

TI.com 無法提供

偵錯探測器

TMDSEMU560V2STM-U — XDS560v2 System Trace USB 偵錯探測器

XDS560v2 是 XDS560™ 偵錯探測器系列的最高性能表現，支援傳統 JTAG 標準 (IEEE1149.1) 和 cJTAG (IEEE1149.7)。請注意，序列線偵錯 (SWD) 不受支援。

所有 XDS 偵錯探測器均支援所有具有嵌入式追踪緩衝區 (ETB) 的 ARM 和 DSP 處理器中的核心和系統追蹤功能。對於針腳追蹤則需要 XDS560v2 PRO TRACE。

XDS560v2 透過 MIPI HSPT 60 針腳接頭 (具有用於 TI 14 針腳、TI 20 針腳和 ARM 20 針腳的多轉接器) 連接到目標電路板，並透過 USB2.0 高速 (480Mbps) (...)

TI.com 無法提供

偵錯探測器

TMDSEMU560V2STM-UE — XDS560v2 System Trace USB 與乙太網路偵錯探測器

The XDS560v2 is the highest performance of the XDS560™ family of debug probes and supports both the traditional JTAG standard (IEEE1149.1) and cJTAG (IEEE1149.7). Note that it does not support serial wire debug (SWD).

All XDS debug probes support Core and System Trace in all ARM and DSP processors (...)