SBOS309E August   2004  – December 2024 OPA2830

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison Table
  6. 5 Pin Configurations and Functions
  7. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Electrical Characteristics VS = ±5V
    6. 6.6  Electrical Characteristics VS = 5V
    7. 6.7  Electrical Characteristics VS = 3V
    8. 6.8  Typical Characteristics: VS = ±5V
    9. 6.9  Typical Characteristics: VS = ±5V, Differential Configuration
    10. 6.10 Typical Characteristics: VS = 5V
    11. 6.11 Typical Characteristics: VS = 5V, Differential Configuration
    12. 6.12 Typical Characteristics: VS = 3V
    13. 6.13 Typical Characteristics: VS = 3V, Differential Configuration
  8. 7 Parameter Measurement Information
  9. 8 Application and Implementation
    1. 8.1 Application Information
      1. 8.1.1  Wideband Voltage-Feedback Operation
      2. 8.1.2  Single-Supply ADC Interface
      3. 8.1.3  DC Level-Shifting
      4. 8.1.4  AC-Coupled Output Video Line Driver
      5. 8.1.5  Noninverting Amplifier With Reduced Peaking
      6. 8.1.6  Single-Supply Active Filter
      7. 8.1.7  Differential Low-Pass Active Filters
      8. 8.1.8  High-Pass Filters
      9. 8.1.9  High-Performance DAC Transimpedance Amplifier
      10. 8.1.10 Operating Suggestions Optimizing Resistor Values
      11. 8.1.11 Bandwidth vs Gain: Noninverting Operation
      12. 8.1.12 Inverting Amplifier Operation
      13. 8.1.13 Output Current and Voltages
      14. 8.1.14 Driving Capacitive Loads
      15. 8.1.15 Distortion Performance
      16. 8.1.16 Noise Performance
      17. 8.1.17 DC Accuracy and Offset Control
    2. 8.2 Power Supply Recommendations
      1. 8.2.1 Thermal Analysis
    3. 8.3 Layout
      1. 8.3.1 Board Layout Guidelines
        1. 8.3.1.1 Input and ESD Protection
  10. 9 Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Design-In Tools
        1. 9.1.1.1 Demonstration Fixtures
        2. 9.1.1.2 Macro-model and Applications Support
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

Package Options

Refer to the PDF data sheet for device specific package drawings

Mechanical Data (Package|Pins)
  • D|8
  • DGK|8
Thermal pad, mechanical data (Package|Pins)
Orderable Information

6.8 Typical Characteristics: VS = ±5V

at TA = 25°C, G = +2V/V, RF = 750Ω, and RL = 150Ω to GND (unless otherwise noted); see Figure 8-3

OPA2830 Noninverting Small-Signal Frequency Response
RL = 150Ω VO = 0.2VPP
Figure 6-1 Noninverting Small-Signal Frequency Response
OPA2830 Noninverting Large-Signal Frequency Response
RL = 150Ω G = +2V/V
Figure 6-3 Noninverting Large-Signal Frequency Response
OPA2830 Noninverting Pulse Response
G = +2V/V
Figure 6-5 Noninverting Pulse Response
OPA2830 Harmonic Distortion vs Load Resistance
f = 5MHz VO = 2VPP G = +2V/V
Figure 6-7 Harmonic Distortion vs Load Resistance
OPA2830 Harmonic Distortion vs Output Voltage
f = 5MHz RL = 500Ω G = +2V/V
Figure 6-9 Harmonic Distortion vs Output Voltage
OPA2830 Two-Tone, 3rd-Order Intermodulation Spurious
 
Figure 6-11 Two-Tone, 3rd-Order Intermodulation Spurious
OPA2830 Frequency Response vs Capacitive Load
 
Figure 6-13 Frequency Response vs Capacitive Load
OPA2830 Output Swing vs Load Resistance
 
Figure 6-15 Output Swing vs Load Resistance
OPA2830 Inverting Small-Signal Frequency Response
RL = 150Ω VO = 0.2VPP
Figure 6-2 Inverting Small-Signal Frequency Response
OPA2830 Inverting Large-Signal Frequency Response
RL = 150Ω G = –1V/V
Figure 6-4 Inverting Large-Signal Frequency Response
OPA2830 Inverting Pulse Response
G = –1V/V
Figure 6-6 Inverting Pulse Response
OPA2830 5MHz Harmonic Distortion vs Supply Voltage
RL = 500Ω VO = 2VPP G = +2V/V
Figure 6-8 5MHz Harmonic Distortion vs Supply Voltage
OPA2830 Harmonic Distortion vs Frequency
VO = 2VPP G = +2V/V
Figure 6-10 Harmonic Distortion vs Frequency
OPA2830 Supply and Output Current vs Temperature
 
Figure 6-12 Supply and Output Current vs Temperature
OPA2830 Recommended RS vs Capacitive Load
 
Figure 6-14 Recommended RS vs Capacitive Load
OPA2830 Output Voltage and Current Limitations
 
Figure 6-16 Output Voltage and Current Limitations