SLASEM6C October   2017  – October 2020 TAS2770

PRODUCTION DATA  

  1. Features
  2. Applications
  3. Description
  4. Revision History
  5. Pin Configuration and Functions
    1.     Pin Functions
  6. Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 I2C Timing Requirements
    7. 6.7 TDM Port Timing Requirements
    8. 6.8 PDM Port Timing Requirements
    9. 6.9 Typical Characteristics
  7. Parameter Measurement Information
  8. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Device Mode and Address Selection
      2. 8.3.2 General I2C Operation
      3. 8.3.3 Single-Byte and Multiple-Byte Transfers
      4. 8.3.4 Single-Byte Write
      5. 8.3.5 Multiple-Byte Write and Incremental Multiple-Byte Write
      6. 8.3.6 Single-Byte Read
      7. 8.3.7 Multiple-Byte Read
      8. 8.3.8 Register Organization
    4. 8.4 Device Functional Modes
      1. 8.4.1  PDM Input
      2. 8.4.2  TDM Port
      3. 8.4.3  Playback Signal Path
        1. 8.4.3.1 High Pass Filter
        2. 8.4.3.2 Digital Volume Control and Amplifier Output Level
        3. 8.4.3.3 Audio Playback Selection
        4. 8.4.3.4 Battery Tracking Limiter with Brown Out Prevention
        5. 8.4.3.5 Inter Chip Limiter Alignment
          1. 8.4.3.5.1 TDM Mode
        6. 8.4.3.6 Class-D Settings
      4. 8.4.4  SAR ADC
      5. 8.4.5  IV Sense
      6. 8.4.6  Clocks and PLL
      7. 8.4.7  Operational Modes
        1. 8.4.7.1 Hardware Shutdown
        2. 8.4.7.2 Software Shutdown
        3. 8.4.7.3 Mute
        4. 8.4.7.4 Active
        5. 8.4.7.5 Mode Control and Software Reset
      8. 8.4.8  Faults and Status
      9. 8.4.9  Power Sequencing Requirements
      10. 8.4.10 Digital Input Pull Downs
    5. 8.5 Register Maps
      1. 8.5.1 Register Summary Table Book=0x00 Page=0x00
      2. 8.5.2 Register Maps
        1. 8.5.2.1  PAGE (book=0x00 page=0x00 address=0x00) [reset=0h]
        2. 8.5.2.2  SW_RESET (book=0x00 page=0x00 address=0x01) [reset=0h]
        3. 8.5.2.3  PWR_CTL (book=0x00 page=0x00 address=0x02) [reset=Eh]
        4. 8.5.2.4  PB_CFG0 (book=0x00 page=0x00 address=0x03) [reset=10h]
        5. 8.5.2.5  PB_CFG1 (book=0x00 page=0x00 address=0x04) [reset=1h]
        6. 8.5.2.6  PB_CFG2 (book=0x00 page=0x00 address=0x05) [reset=0h]
        7. 8.5.2.7  PB_CFG3 (book=0x00 page=0x00 address=0x06) [reset=0h]
        8. 8.5.2.8  MISC_CFG (book=0x00 page=0x00 address=0x07) [reset=6h]
        9. 8.5.2.9  PDM_CFG0 (book=0x00 page=0x00 address=0x08) [reset=0h]
        10. 8.5.2.10 PDM_CFG1 (book=0x00 page=0x00 address=0x09) [reset=8h]
        11. 8.5.2.11 TDM_CFG0 (book=0x00 page=0x00 address=0x0A) [reset=7h]
        12. 8.5.2.12 TDM_CFG1 (book=0x00 page=0x00 address=0x0B) [reset=2h]
        13. 8.5.2.13 TDM_CFG2 (book=0x00 page=0x00 address=0x0C) [reset=Ah]
        14. 8.5.2.14 TDM_CFG3 (book=0x00 page=0x00 address=0x0D) [reset=10h]
        15. 8.5.2.15 TDM_CFG4 (book=0x00 page=0x00 address=0x0E) [reset=13h]
        16. 8.5.2.16 TDM_CFG5 (book=0x00 page=0x00 address=0x0F) [reset=2h]
        17. 8.5.2.17 TDM_CFG6 (book=0x00 page=0x00 address=0x10) [reset=0h]
        18. 8.5.2.18 TDM_CFG7 (book=0x00 page=0x00 address=0x11) [reset=4h]
        19. 8.5.2.19 TDM_CFG8 (book=0x00 page=0x00 address=0x12) [reset=6h]
        20. 8.5.2.20 TDM_CFG9 (book=0x00 page=0x00 address=0x13) [reset=7h]
        21. 8.5.2.21 TDM_CFG10 (book=0x00 page=0x00 address=0x14) [reset=8h]
        22. 8.5.2.22 LIM_CFG0 (book=0x00 page=0x00 address=0x15) [reset=14h]
        23. 8.5.2.23 LIM_CFG1 (book=0x00 page=0x00 address=0x16) [reset=76h]
        24. 8.5.2.24 LIM_CFG2 (book=0x00 page=0x00 address=0x17) [reset=10h]
        25. 8.5.2.25 LIM_CFG3 (book=0x00 page=0x00 address=0x18) [reset=6Eh]
        26. 8.5.2.26 LIM_CFG4 (book=0x00 page=0x00 address=0x19) [reset=1Eh]
        27. 8.5.2.27 LIM_CFG5 (book=0x00 page=0x00 address=0x1A) [reset=58h]
        28. 8.5.2.28 BOP_CFG0 (book=0x00 page=0x00 address=0x1B) [reset=1h]
        29. 8.5.2.29 BOP_CFG1 (book=0x00 page=0x00 address=0x1C) [reset=14h]
        30. 8.5.2.30 BOP_CFG2 (book=0x00 page=0x00 address=0x1D) [reset=4Eh]
        31. 8.5.2.31 ICLA_CFG0 (book=0x00 page=0x00 address=0x1E) [reset=0h]
        32. 8.5.2.32 ICLA_CFG1 (book=0x00 page=0x00 address=0x1F) [reset=0h]
        33. 8.5.2.33 INT_MASK0 (book=0x00 page=0x00 address=0x20) [reset=FCh]
        34. 8.5.2.34 INT_MASK1 (book=0x00 page=0x00 address=0x21) [reset=B1h]
        35. 8.5.2.35 INT_LIVE0 (book=0x00 page=0x00 address=0x22) [reset=0h]
        36. 8.5.2.36 INT_LIVE1 (book=0x00 page=0x00 address=0x23) [reset=0h]
        37. 8.5.2.37 INT_LTCH0 (book=0x00 page=0x00 address=0x24) [reset=0h]
        38. 8.5.2.38 INT_LTCH1 (book=0x00 page=0x00 address=0x25) [reset=0h]
        39. 8.5.2.39 INT_LTCH2 (book=0x00 page=0x00 address=0x26) [reset=0h]
        40. 8.5.2.40 VBAT_MSB (book=0x00 page=0x00 address=0x27) [reset=0h]
        41. 8.5.2.41 VBAT_LSB (book=0x00 page=0x00 address=0x28) [reset=0h]
        42. 8.5.2.42 TEMP_MSB (book=0x00 page=0x00 address=0x29) [reset=0h]
        43. 8.5.2.43 TEMP_LSB (book=0x00 page=0x00 address=0x2A) [reset=0h]
        44. 8.5.2.44 INT_CFG (book=0x00 page=0x00 address=0x30) [reset=5h]
        45. 8.5.2.45 DIN_PD (book=0x00 page=0x00 address=0x31) [reset=0h]
        46. 8.5.2.46 MISC_IRQ (book=0x00 page=0x00 address=0x32) [reset=81h]
        47. 8.5.2.47 CLOCK_CFG (book=0x00 page=0x00 address=0x3C) [reset=Dh]
        48. 8.5.2.48 TDM_DET (book=0x00 page=0x00 address=0x77) [reset=7Fh]
        49. 8.5.2.49 REV_ID (book=0x00 page=0x00 address=0x7D) [reset=20h]
        50. 8.5.2.50 I2C_CKSUM (book=0x00 page=0x00 address=0x7E) [reset=0h]
        51. 8.5.2.51 BOOK (book=0x00 page=0x00 address=0x7F) [reset=0h]
  9. Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Overview
        2. 9.2.2.2 Select Input Capacitance
        3. 9.2.2.3 Select Decoupling Capacitors
        4. 9.2.2.4 Select Bootstrap Capacitors
      3. 9.2.3 Application Curves
    3. 9.3 Initialization Set Up
      1. 9.3.1 Initial Device Configuration - Auto Rate
      2. 9.3.2 Initial Device Configuration - 48 kHz
      3. 9.3.3 Initial Device Configuration - 44.1 kHz
      4. 9.3.4 Sample Rate Change - 48 kHz to 44.1kHz
      5. 9.3.5 Sample Rate Change - 44.1 kHz to 48 kHz
      6. 9.3.6 Device Mute
      7. 9.3.7 Device Un-Mute
      8. 9.3.8 Device Sleep
      9. 9.3.9 Device Wake
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Receiving Notification of Documentation Updates
    2. 12.2 Community Resources
    3. 12.3 Trademarks
  13. 13Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

PDM Input

The TAS2770 provides one PDM input that can be used for low latency audio playback or sensor aggregation in TDM/I2C mode. Figure 8-6 below illustrates the double data rate nature of the PDM inputs. Each input has two interleaved PDM channels, one sampled by the rising edge and the other by the falling edge of the clock.

GUID-71F36E3B-59A9-4864-A748-41A05835A965-low.gifFigure 8-6 PDM Waveform

The PDM inputs are sampled by the PDMCK pin, which can be independently configured as either a PDM clock slave input or a PDM clock master output. The PDM_EDGE[1:0] and PDM_SLV[1:0] register bits select the sample clock edge and master/slave mode for each of the two PDM inputs. In master mode the PDMCK pin can disable the clocks (and drive a logic 0) by setting the PDM_GATE[1:0] register bits low. The PDM_CLK[1:0] register bits select which clock is used to sample each PDM input.

GUID-FD64C90D-3D80-47CC-A340-A0798071A078-low.gif Figure 8-7 PDM Data and Clock Input Block Diagram

When configured as a clock slave, the PDM clock input does not require a specific phase relationship to the system clock (SBCLK in TDM/I2C Mode), but must have an exact frequency relationship to the audio sample rate. This is equivalent to 64/32/16 (~3 MHz) or 128/64/32 (~6 MHz) times a single/double/quadruple speed sample rate. The PDM rate is set by the PDM_RATE1[1:0] register bits.

When the PDMCK pin is configured as a clock master, the TAS2770 will output a 50% duty cycle clock of frequency that is set by the PDM_RATE1[1:0] register bits (64/32/16 or 128/64/32 times a single/double/quadruple speed sample rate).

The PDM_MAP register bit selects which PDM pin is used for audio playback input and which is used for PDM sensor input. The PDM sensor input can be decimated (time aligned with the IV sense) and transmitted on the SDOUT pin when the device is in TDM/I2C mode.

Table 8-2 PDM Input Capture Edge
PDM Input PinRegister BitValueCapture Edge
PDMDPDM_EDGE[1]
0
Rising (default)
1
Falling
Table 8-3 PDM Clock Slave
PDM Input PinRegister BitValueMaster/Slave
PDMDPDM_SLV[1]
0
Slave (default)
1
Master
Table 8-4 PDM Clock Select
PDM Input PinRegister BitValueClock Source
PDMDPDM_CLK[1]
0
GND
1
PDMCK (default)
Table 8-5 PDM Master Mode Clock Gate
PDM Clock PinRegister BitValueGating
PDMCKPDM_GATE[1]
0
Gated Off (default)
1
Active
Table 8-6 PDM Input Sample Rate
PDM Input PinRegister BitsValueSample Rate
PDMDPDM_RATE1[1:0]
00
2.54 - 3.38 MHz (default)
01
5.08 - 6.76 MHz
10
Reserved
11
Reserved
Table 8-7 PDM Pin Mapping
PDM_MAPMapping
0
PDMD pin for sensor input (default)
1
PDMD pin for playback