SLASEM6C October   2017  – October 2020 TAS2770

PRODUCTION DATA  

  1. Features
  2. Applications
  3. Description
  4. Revision History
  5. Pin Configuration and Functions
    1.     Pin Functions
  6. Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 I2C Timing Requirements
    7. 6.7 TDM Port Timing Requirements
    8. 6.8 PDM Port Timing Requirements
    9. 6.9 Typical Characteristics
  7. Parameter Measurement Information
  8. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Device Mode and Address Selection
      2. 8.3.2 General I2C Operation
      3. 8.3.3 Single-Byte and Multiple-Byte Transfers
      4. 8.3.4 Single-Byte Write
      5. 8.3.5 Multiple-Byte Write and Incremental Multiple-Byte Write
      6. 8.3.6 Single-Byte Read
      7. 8.3.7 Multiple-Byte Read
      8. 8.3.8 Register Organization
    4. 8.4 Device Functional Modes
      1. 8.4.1  PDM Input
      2. 8.4.2  TDM Port
      3. 8.4.3  Playback Signal Path
        1. 8.4.3.1 High Pass Filter
        2. 8.4.3.2 Digital Volume Control and Amplifier Output Level
        3. 8.4.3.3 Audio Playback Selection
        4. 8.4.3.4 Battery Tracking Limiter with Brown Out Prevention
        5. 8.4.3.5 Inter Chip Limiter Alignment
          1. 8.4.3.5.1 TDM Mode
        6. 8.4.3.6 Class-D Settings
      4. 8.4.4  SAR ADC
      5. 8.4.5  IV Sense
      6. 8.4.6  Clocks and PLL
      7. 8.4.7  Operational Modes
        1. 8.4.7.1 Hardware Shutdown
        2. 8.4.7.2 Software Shutdown
        3. 8.4.7.3 Mute
        4. 8.4.7.4 Active
        5. 8.4.7.5 Mode Control and Software Reset
      8. 8.4.8  Faults and Status
      9. 8.4.9  Power Sequencing Requirements
      10. 8.4.10 Digital Input Pull Downs
    5. 8.5 Register Maps
      1. 8.5.1 Register Summary Table Book=0x00 Page=0x00
      2. 8.5.2 Register Maps
        1. 8.5.2.1  PAGE (book=0x00 page=0x00 address=0x00) [reset=0h]
        2. 8.5.2.2  SW_RESET (book=0x00 page=0x00 address=0x01) [reset=0h]
        3. 8.5.2.3  PWR_CTL (book=0x00 page=0x00 address=0x02) [reset=Eh]
        4. 8.5.2.4  PB_CFG0 (book=0x00 page=0x00 address=0x03) [reset=10h]
        5. 8.5.2.5  PB_CFG1 (book=0x00 page=0x00 address=0x04) [reset=1h]
        6. 8.5.2.6  PB_CFG2 (book=0x00 page=0x00 address=0x05) [reset=0h]
        7. 8.5.2.7  PB_CFG3 (book=0x00 page=0x00 address=0x06) [reset=0h]
        8. 8.5.2.8  MISC_CFG (book=0x00 page=0x00 address=0x07) [reset=6h]
        9. 8.5.2.9  PDM_CFG0 (book=0x00 page=0x00 address=0x08) [reset=0h]
        10. 8.5.2.10 PDM_CFG1 (book=0x00 page=0x00 address=0x09) [reset=8h]
        11. 8.5.2.11 TDM_CFG0 (book=0x00 page=0x00 address=0x0A) [reset=7h]
        12. 8.5.2.12 TDM_CFG1 (book=0x00 page=0x00 address=0x0B) [reset=2h]
        13. 8.5.2.13 TDM_CFG2 (book=0x00 page=0x00 address=0x0C) [reset=Ah]
        14. 8.5.2.14 TDM_CFG3 (book=0x00 page=0x00 address=0x0D) [reset=10h]
        15. 8.5.2.15 TDM_CFG4 (book=0x00 page=0x00 address=0x0E) [reset=13h]
        16. 8.5.2.16 TDM_CFG5 (book=0x00 page=0x00 address=0x0F) [reset=2h]
        17. 8.5.2.17 TDM_CFG6 (book=0x00 page=0x00 address=0x10) [reset=0h]
        18. 8.5.2.18 TDM_CFG7 (book=0x00 page=0x00 address=0x11) [reset=4h]
        19. 8.5.2.19 TDM_CFG8 (book=0x00 page=0x00 address=0x12) [reset=6h]
        20. 8.5.2.20 TDM_CFG9 (book=0x00 page=0x00 address=0x13) [reset=7h]
        21. 8.5.2.21 TDM_CFG10 (book=0x00 page=0x00 address=0x14) [reset=8h]
        22. 8.5.2.22 LIM_CFG0 (book=0x00 page=0x00 address=0x15) [reset=14h]
        23. 8.5.2.23 LIM_CFG1 (book=0x00 page=0x00 address=0x16) [reset=76h]
        24. 8.5.2.24 LIM_CFG2 (book=0x00 page=0x00 address=0x17) [reset=10h]
        25. 8.5.2.25 LIM_CFG3 (book=0x00 page=0x00 address=0x18) [reset=6Eh]
        26. 8.5.2.26 LIM_CFG4 (book=0x00 page=0x00 address=0x19) [reset=1Eh]
        27. 8.5.2.27 LIM_CFG5 (book=0x00 page=0x00 address=0x1A) [reset=58h]
        28. 8.5.2.28 BOP_CFG0 (book=0x00 page=0x00 address=0x1B) [reset=1h]
        29. 8.5.2.29 BOP_CFG1 (book=0x00 page=0x00 address=0x1C) [reset=14h]
        30. 8.5.2.30 BOP_CFG2 (book=0x00 page=0x00 address=0x1D) [reset=4Eh]
        31. 8.5.2.31 ICLA_CFG0 (book=0x00 page=0x00 address=0x1E) [reset=0h]
        32. 8.5.2.32 ICLA_CFG1 (book=0x00 page=0x00 address=0x1F) [reset=0h]
        33. 8.5.2.33 INT_MASK0 (book=0x00 page=0x00 address=0x20) [reset=FCh]
        34. 8.5.2.34 INT_MASK1 (book=0x00 page=0x00 address=0x21) [reset=B1h]
        35. 8.5.2.35 INT_LIVE0 (book=0x00 page=0x00 address=0x22) [reset=0h]
        36. 8.5.2.36 INT_LIVE1 (book=0x00 page=0x00 address=0x23) [reset=0h]
        37. 8.5.2.37 INT_LTCH0 (book=0x00 page=0x00 address=0x24) [reset=0h]
        38. 8.5.2.38 INT_LTCH1 (book=0x00 page=0x00 address=0x25) [reset=0h]
        39. 8.5.2.39 INT_LTCH2 (book=0x00 page=0x00 address=0x26) [reset=0h]
        40. 8.5.2.40 VBAT_MSB (book=0x00 page=0x00 address=0x27) [reset=0h]
        41. 8.5.2.41 VBAT_LSB (book=0x00 page=0x00 address=0x28) [reset=0h]
        42. 8.5.2.42 TEMP_MSB (book=0x00 page=0x00 address=0x29) [reset=0h]
        43. 8.5.2.43 TEMP_LSB (book=0x00 page=0x00 address=0x2A) [reset=0h]
        44. 8.5.2.44 INT_CFG (book=0x00 page=0x00 address=0x30) [reset=5h]
        45. 8.5.2.45 DIN_PD (book=0x00 page=0x00 address=0x31) [reset=0h]
        46. 8.5.2.46 MISC_IRQ (book=0x00 page=0x00 address=0x32) [reset=81h]
        47. 8.5.2.47 CLOCK_CFG (book=0x00 page=0x00 address=0x3C) [reset=Dh]
        48. 8.5.2.48 TDM_DET (book=0x00 page=0x00 address=0x77) [reset=7Fh]
        49. 8.5.2.49 REV_ID (book=0x00 page=0x00 address=0x7D) [reset=20h]
        50. 8.5.2.50 I2C_CKSUM (book=0x00 page=0x00 address=0x7E) [reset=0h]
        51. 8.5.2.51 BOOK (book=0x00 page=0x00 address=0x7F) [reset=0h]
  9. Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Overview
        2. 9.2.2.2 Select Input Capacitance
        3. 9.2.2.3 Select Decoupling Capacitors
        4. 9.2.2.4 Select Bootstrap Capacitors
      3. 9.2.3 Application Curves
    3. 9.3 Initialization Set Up
      1. 9.3.1 Initial Device Configuration - Auto Rate
      2. 9.3.2 Initial Device Configuration - 48 kHz
      3. 9.3.3 Initial Device Configuration - 44.1 kHz
      4. 9.3.4 Sample Rate Change - 48 kHz to 44.1kHz
      5. 9.3.5 Sample Rate Change - 44.1 kHz to 48 kHz
      6. 9.3.6 Device Mute
      7. 9.3.7 Device Un-Mute
      8. 9.3.8 Device Sleep
      9. 9.3.9 Device Wake
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Receiving Notification of Documentation Updates
    2. 12.2 Community Resources
    3. 12.3 Trademarks
  13. 13Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

Pin Functions

PINI/ODESCRIPTION
DSBGAQFNNAME
D524AREGOGate drive voltage regulator output. Decouple with cap to GND. Do not connect to external load.
C19AVDDPAnalog power input. Connect to 1.8V supply and decouple to GND with cap.
A21BST_NIClass-D negative bootstrap. Connect a cap between BST_N and OUT_N.
B24BST_PIClass-D positive bootstrap. Connect a cap between BST_P and OUT_P.
D17DREGODigital core voltage regulator output. Bypass to GND with a cap. Do not connect to external load.
E214FSYNCITDM Frame Sync.
C2, E3, E410, 15, 16GNDPAnalog GND. Connect to PCB GND Plane.
D28IOVDDPDigital IO Supply. Connect to the same 1.8 V supply that powers AVDD and decouple with a cap to GND.
D420IRQZOOpen drain, actve low interrupt pin. Pull up to IOVDD with resistor if optional internal pull up is not used.
D319MODEIMode detect pin. This pin can detect a short to IOVDD or GND, a 470 Ω connection to IOVDD or GND, a 2.2 kΩ connection to IOVDD or GND, a 10 kΩ connection to IOVDD or GND and a 47 kΩ connection to IOVDD. Minimize capacitive loading on this pin and do not connect to any other load.
A5, B526OUT_NOClass-D negative output.
A3, B33OUT_POClass-D positive output.
F517PDMCKIOPDM Clock.
E518PDMDIPDM Digital Input.
A4, B42PGNDPClass-D GND. Connect to PCB GND Plane.
F113SBCLKITDM Serial Bit Clock in TDM/I2C Mode.
F423SCLII2C Clock Pin. Pull up to IOVDD with a resistor.
F322SDAIOI2C Data Pin. Pull up to IOVDD with a resistor.
F211SDINITDM Serial Data Input.
E112SDOUTIOTDM Serial Data Output in TDM/I2C Mode.
C321SDZIActive low hardware shutdown.
C4, C525VBATPClass-D power supply input. Connect to VBAT supply and decouple with a cap.
B16VSNS_NIVoltage Sense negative input. Connect to Class-D negative output after Ferrite bead filter.
A15VSNS_PIVoltage Sense positive input. Connect to Class-D positive output after Ferrite bead filter.