SLLSF57A August   2022  – April 2024 TMDS1204

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD and Latch-Up Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Switching Characteristics
    8. 5.8 Typical Characteristics
  7. 6 Parameter Measurement Information
  8. 7 Detailed Description
    1. 7.1 Functional Block Diagram
    2. 7.2 Feature Description
      1. 7.2.1  4-Level Inputs
      2. 7.2.2  I/O Voltage Level Selection
      3. 7.2.3  HPD_OUT
      4. 7.2.4  Lane Control
      5. 7.2.5  Swap
      6. 7.2.6  Linear and Limited Redriver
      7. 7.2.7  Main Link Inputs
      8. 7.2.8  Receiver Equalizer
      9. 7.2.9  CTLE Bypass
      10. 7.2.10 Adaptive Equalization in HDMI 2.1 FRL
        1. 7.2.10.1 HDMI 2.1 TX Compliance Testing with AEQ Enabled
      11. 7.2.11 HDMI 2.1 Link Training Compatible Rx EQ
      12. 7.2.12 Input Signal Detect
        1. 7.2.12.1 SIGDET_OUT Indicator
      13. 7.2.13 Main Link Outputs
        1. 7.2.13.1 Transmitter Bias
        2. 7.2.13.2 Transmitter Impedance Control
        3. 7.2.13.3 TX Slew Rate Control
        4. 7.2.13.4 TX Pre-Emphasis and De-Emphasis Control
        5. 7.2.13.5 TX Swing Control
        6. 7.2.13.6 Fan-out Buffer
      14. 7.2.14 HDMI DDC Capacitance
      15. 7.2.15 DisplayPort
    3. 7.3 Device Functional Modes
      1. 7.3.1 MODE Control
        1. 7.3.1.1 I2C Mode (MODE = "F")
        2. 7.3.1.2 Pin Strap Modes
          1. 7.3.1.2.1 Pin-Strap: HDMI 1.4 and HDMI 2.0 Functional Description
          2. 7.3.1.2.2 Pin-Strap HDMI 2.1 Function (MODE = "0"): Fixed Rx EQ)
          3. 7.3.1.2.3 Pin-Strap HDMI 2.1 Function (Mode = "1"): Flexible Rx EQ
          4. 7.3.1.2.4 Pin-Strap HDMI 2.1 Function (Mode = "R"): Flexible Rx EQ and Fan-Out Buffer
      2. 7.3.2 DDC Snoop Feature
        1. 7.3.2.1 HDMI Type
        2. 7.3.2.2 HDMI 2.1 FRL Snoop
      3. 7.3.3 Low Power States
    4. 7.4 Programming
      1. 7.4.1 Pseudocode Examples
        1. 7.4.1.1 HDMI 2.1 Source Example with DDC Snoop Disabled and DDC Buffer Disabled
        2. 7.4.1.2 Sink Example
      2. 7.4.2 TMDS1204 I2C Address Options
      3. 7.4.3 I2C Target Behavior
    5. 7.5 Register Maps
      1. 7.5.1 TMDS1204 Registers
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Source-Side Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Pre-Channel (LAB)
        2. 8.2.2.2 Post-Channel (LCD)
        3. 8.2.2.3 Common Mode Choke
        4. 8.2.2.4 ESD Protection
      3. 8.2.3 Application Curves
    3. 8.3 Typical Sink-Side Application
      1. 8.3.1 Design Requirements
      2. 8.3.2 Detailed Design Procedures
    4. 8.4 Power Supply Recommendations
      1. 8.4.1 Supply Decoupling
    5. 8.5 Layout
      1. 8.5.1 Layout Guidelines
      2. 8.5.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Documentation Support
      1. 9.1.1 Related Documentation
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7.2.1 4-Level Inputs

The TMDS1204 has 4-level inputs pins that control the receiver equalization gain, transmitter voltage swing, and pre-emphasis, and place TMDS1204 into different modes of operation. These 4-level inputs utilize a resistor divider to help set the 4 valid levels and provide a wider range of control settings. There are internal pull-up and a pull-down resistors. These resistors are combined with the external resistor connection to achieve the desired voltage level.

Table 7-1 4-Level Control Pin Settings
LEVELSETTINGS
0Tie 1kΩ 5% to GND.
RTie 20kΩ 5% to GND.
FFloat (leave pin open)
1Tie 1kΩ 5% to VCC.
Note: Figure 6-1 shows how all 4-level inputs are latched after the rising edge of the EN pin. After these pins are sampled, the internal pull-up and pull-down resistors will be isolated to save power.