SLVSFZ2C April   2023  – February 2024 TPS274C65

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison Table
  6. 5 Pin Configuration and Functions
    1.     7
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Switching Characteristics
    7. 6.7 SPI Timing Requirements
    8. 6.8 Typical Characteristics
  8. 7 Parameter Measurement Information
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Pin Diagrams
      2. 8.3.2 SPI Mode Operation
        1. 8.3.2.1 Diagnostic Bit Behavior
      3. 8.3.3 Programmable Current Limit
        1. 8.3.3.1 Inrush Current Handling
      4. 8.3.4 DO_EN Feature
      5. 8.3.5 Protection Mechanisms
        1. 8.3.5.1 Overcurrent Protection
        2. 8.3.5.2 Short Circuit Protection
          1. 8.3.5.2.1 VS During Short-to-Ground
        3. 8.3.5.3 Inductive-Load Switching-Off Clamp
        4. 8.3.5.4 Inductive Load Demagnetization
        5. 8.3.5.5 Thermal Shutdown
        6. 8.3.5.6 Undervoltage protection on VS
        7. 8.3.5.7 Undervoltage Lockout on Low Voltage Supply (VDD_UVLO)
        8. 8.3.5.8 Power-Up and Power-Down Behavior
        9. 8.3.5.9 Reverse Current Blocking
      6. 8.3.6 Diagnostic Mechanisms
        1. 8.3.6.1 Current Sense
          1. 8.3.6.1.1 RSNS Value
            1. 8.3.6.1.1.1 SNS Output Filter
        2. 8.3.6.2 Fault Indication
          1. 8.3.6.2.1 Current Limit Behavior
        3. 8.3.6.3 Short-to-Battery and Open-Load Detection
        4. 8.3.6.4 On-State Wire-Break Detection
        5. 8.3.6.5 Off State Wire-Break Detection
        6. 8.3.6.6 ADC
      7. 8.3.7 LED Driver
    4. 8.4 Device Functional Modes
      1. 8.4.1 OFF/POR
      2. 8.4.2 INIT
      3. 8.4.3 Active
    5. 8.5 TPS274C65BS Available Registers List
    6. 8.6 TPS274C65 Registers
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 IEC 61000-4-5 Surge
        2. 9.2.2.2 Loss of GND
        3. 9.2.2.3 Paralleling Channels
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Receiving Notification of Documentation Updates
    2. 10.2 Support Resources
    3. 10.3 Trademarks
    4. 10.4 Electrostatic Discharge Caution
    5. 10.5 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

8.3.7 LED Driver

TPS274C65 integrates an LED driver designed to drive 8 Status LEDs using only 4 outputs(LEDOUT1-LEDOUT4). This design provides the flexibility to ensure any combination of LEDs can be turned on at any given time and the user can configure the outputs through SPI using the TPS274C65 Registers. This LED driver is designed to control each output with independent clock signals with ON phases offset from each other. This ensures maximum flexibility for the user assigning use cases when configuring LED driver.

An example application is to provide ON/OFF channel status and fault indication per channel. In this example, the user could assign channel specific functionality for D1-D4 such as channel on or off and tie D5-D8 as fault indication LEDs. However, the user has full discretion on how they want to leverage these outputs.

RS and RF resistors determine the LED current through each LED and should be chosen according to the LED's current/light density specifications. Current will flow from VDD pins to the LEDs, and the average current through each LED will be VDD/RS(or RF)/4.

GUID-20231017-SS0I-DP3B-GWPM-X0DKHPKVFC59-low.svg Figure 8-40 LED Driver