SLVSHM3 November   2026 TPS2HCS05-Q1

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison Table
  6. 5 Pin Configuration and Functions
    1. 5.1 Package
    2. 5.2 Pinout A-version
    3. 5.3 Version B Package
    4. 5.4 Pinout B-version
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 SPI Timing Requirements
    7. 6.7 Switching Characteristics
    8. 6.8 Typical Characteristics
  8. 7 Parameter Measurement Information
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Device Functional Modes
      1. 8.3.1  State Diagram
      2. 8.3.2  Output Control
        1. 8.3.2.1 Output Control - Version A
        2. 8.3.2.2 Pin 5 Functions (DI or OUT_DIS) - Version A
        3. 8.3.2.3 Output Control - Version B
      3. 8.3.3  Output Disable Function (OUT_DIS)
      4. 8.3.4  SPI Mode Operation
        1. 8.3.4.1 SPI
        2. 8.3.4.2 Chip Select (CS or nCS)
        3. 8.3.4.3 System Clock
        4. 8.3.4.4 Serial Data In (SDI) and Serial Data Out (SDO)
        5. 8.3.4.5 CRC Error Detection and Checking of Clocks
        6. 8.3.4.6 SPI Frame Format
        7. 8.3.4.7 GLOBAL_FAULT_TYPE [15:8] Bits
        8. 8.3.4.8 SPI Watchdog Function
        9. 8.3.4.9 SPI Watchdog Operation - TPS2HCS05A-Q1
      5. 8.3.5  Fault Reporting
      6. 8.3.6  SLEEP
      7. 8.3.7  CONFIG/ACTIVE
      8. 8.3.8  LIMP_HOME State (Version A Only)
        1. 8.3.8.1 LIMP HOME State Exceptions
      9. 8.3.9  Battery Supply Input (VBB) Under-Voltage
        1. 8.3.9.1 VBB During Short-to-Ground
      10. 8.3.10 LOW POWER MODE (LPM) States
        1. 8.3.10.1 MANUAL_LPM State
          1. 8.3.10.1.1 System Wakeup from MANUAL_LPM
          2. 8.3.10.1.2 Automatic Exit from MANUAL_LPM
        2. 8.3.10.2 AUTO_LPM State
          1. 8.3.10.2.1 System Wakeup from AUTO_LPM
          2. 8.3.10.2.2 Automatic Exit from AUTO_LPM
    4. 8.4 Feature Description
      1. 8.4.1 Protection Mechanisms
        1. 8.4.1.1 Overcurrent Protection
          1. 8.4.1.1.1 Inrush Period - Overcurrent Protection
            1. 8.4.1.1.1.1 No Capacitive Charging - CAP_CHRG_CHx [1:0] = 00
            2. 8.4.1.1.1.2 Current Limit Regulation Capacitive Charging Mode - CAP_CHRG_CHx [1:0] = 10
          2. 8.4.1.1.2 Overcurrent Protection - Steady State Operation
          3. 8.4.1.1.3 Programmable Fuse Protection
          4. 8.4.1.1.4 Immediate Shutdown Overcurrent Protection (IOCP)
          5. 8.4.1.1.5 Auto retry and latch-off behavior
            1. 8.4.1.1.5.1 Auto retry behavior - No capacitive charging mode (CAP_CHRG_CHx = 00)
            2. 8.4.1.1.5.2 Latch-off Behavior - No Capacitive Charging Mode (CAP_CHRG_CHx = 00)
            3. 8.4.1.1.5.3 Auto Retry Behavior - Current Limit Regulation Charging Mode (CAP_CHRG_CHx = 10)
            4. 8.4.1.1.5.4 Latch-off Behavior - Current Limit Regulation Capactive Charging Mode (CAP_CHRG_CHx = 10)
        2. 8.4.1.2 Thermal Shutdown
          1. 8.4.1.2.1 Relative Thermal Shutdown (TREL)
          2. 8.4.1.2.2 Absolute Thermal Shutdown (TABS)
        3. 8.4.1.3 Reverse Battery
      2. 8.4.2 Diagnostic Mechanisms
        1. 8.4.2.1 Integrated ADC
        2. 8.4.2.2 Digital Current Sense Output
        3. 8.4.2.3 Output Voltage Measurement
        4. 8.4.2.4 MOSFET Temperature Measurement
        5. 8.4.2.5 Drain-to-Source Voltage (VDS) Measurement
        6. 8.4.2.6 VBB Voltage Measurement
        7. 8.4.2.7 VOUT Short-to-Battery and Open-Load
          1. 8.4.2.7.1 Measurement with Channel Output (FET) Enabled
          2. 8.4.2.7.2 Detection with Channel Output Disabled
            1. 8.4.2.7.2.1 Off-State Open Load Detection
            2. 8.4.2.7.2.2 Off-State Short-to-Battery Detection
            3. 8.4.2.7.2.3 Distinguishing Between Open Load and Short-to-Battery Faults
      3. 8.4.3 EEPROM Overview
        1. 8.4.3.1 EEPROM Programming Procedure
        2. 8.4.3.2 Customer Defined Programmable Registers
  10. 9 TPS2HCS05-Q1 Registers
  11. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 Thermal Considerations
        2. 10.2.2.2 Configuring the Capacitive Charging Mode
      3. 10.2.3 Application Curves
    3. 10.3 Power Supply Recommendations
    4. 10.4 Layout
      1. 10.4.1 Layout Guidelines
      2. 10.4.2 Layout Example
  12. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 Third-Party Products Disclaimer
    2. 11.2 Support Resources
    3. 11.3 Trademarks
    4. 11.4 Electrostatic Discharge Caution
    5. 11.5 Glossary
  13. 12Revision History
  14. 13Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
  • PWC|18
Thermal pad, mechanical data (Package|Pins)
Orderable Information

8.4.2.6 VBB Voltage Measurement

The TPS2HCS05-Q1 provides a VBB voltage measurement through the 10-bit ADC.

The VBB voltage measurement is disabled by default. The VBB voltage sense function can be enabled through the ADC_VBB_DIS bit in the ADC_CONFIG register.

The conversion equation for the VBB voltage measurement is detailed in Equation 15. The ADC measurement result is available in the ADC_RESULT_VBB register. The VBB_RDY bit is set to 1 if a new ADC conversion result exists since the register is last read. If any of the channels are in the I2T loop (I2T_MOD_CHx = 1), the VBB voltage measurement, if enabled, is disabled and the VBB_RDY bit is 0. Once the channel(s) exit the I2T loop (I2T_MOD_CHx = 0), then the VBB voltage measurement is automatically re-enabled if previously enabled before the I2T event.

Equation 15. V B B   ( V ) =   18.18   ×   V A D C R E F H I 1023   ×   1.667 ×   A D C _ R E S U L T _ V B B

The VBB voltage measurement is referenced to the device ground so if there is a ground network used for reverse battery then there can be an offset in the voltage measurement.