JAJSQ73C
june 2014 – may 2023
TPS65263
PRODUCTION DATA
1
1
特長
2
アプリケーション
3
概要
4
Revision History
5
Device Comparison Table
6
Pin Configuration and Functions
7
Specifications
7.1
Absolute Maximum Ratings
7.2
ESD Ratings
7.3
Recommended Operating Conditions
7.4
Thermal Information
7.5
Electrical Characteristics
7.6
Typical Characteristics
8
Detailed Description
8.1
Overview
8.2
Functional Block Diagram
8.3
Feature Description
8.3.1
Adjusting the Output Voltage
8.3.2
Enable and Adjusting UVLO
8.3.3
Soft-Start Time
8.3.4
Power-Up Sequencing
8.3.5
V7V Low Dropout Regulator and Bootstrap
8.3.6
Out-of-Phase Operation
8.3.7
Output Overvoltage Protection (OVP)
8.3.8
Pulse Skipping Mode (PSM)
8.3.9
Slope Compensation
8.3.10
Overcurrent Protection
8.3.10.1
High-Side MOSFET Overcurrent Protection
8.3.10.2
Low-Side MOSFET Overcurrent Protection
8.3.11
Power Good
8.3.12
Thermal Shutdown
8.4
Device Functional Modes
8.4.1
Serial Interface Description
8.4.2
I2C Update Sequence
8.5
Register Maps
8.5.1
Register Description
8.5.2
VOUT1_SEL: Vout1 Voltage Selection Register (offset = 0x00H)
8.5.3
VOUT2_SEL: Vout2 Voltage Selection Register (offset = 0x01H)
8.5.4
VOUT3_SEL: Vout3 Voltage Selection Register (offset = 0x02H)
8.5.5
VOUT1_COM: Buck1 Command Register (offset = 0x03H)
8.5.6
VOUT2_COM: Buck2 Command Register (offset = 0x04H)
8.5.7
VOUT3_COM: Buck3 Command Register (offset = 0x05H)
8.5.8
SYS_STATUS: System Status Register (offset = 0x06H)
9
Application and Implementation
9.1
Application Information
9.2
Typical Application
9.2.1
Design Requirements
9.2.2
Detailed Design Procedure
9.2.2.1
Output Inductor Selection
9.2.2.2
Output Capacitor Selection
9.2.2.3
Input Capacitor Selection
9.2.2.4
Loop Compensation
9.2.3
Application Curves
9.3
Power Supply Recommendations
9.4
Layout
9.4.1
Layout Guidelines
9.4.2
Layout Example
10
Device and Documentation Support
10.1
ドキュメントの更新通知を受け取る方法
10.2
サポート・リソース
10.3
Trademarks
10.4
静電気放電に関する注意事項
10.5
用語集
11
Mechanical, Packaging, and Orderable Information
1
特長
動作入力電圧範囲 4.5~18V、連続出力電流 3A / 2A / 2A
各バックの出力電圧は I
2
C 制御の 7 ビット VID により 0.68~1.95V の範囲で 10mV 刻みにプログラム可能
I
2
C により VID 電圧遷移スルーレートを制御
I
2
C により各バックのパワー・グッド・ステータス、過電流警告を読み出し
I
2
C によりバックのダイ温度警告を読み出し
I
2
C 互換のインターフェイス、スタンダード・モード (100kHz) とファスト・モード (400kHz) に対応
帰還基準電圧:0.6V±1%
600kHz の固定周波数
各バックに専用のイネーブル・ピンとソフト・スタート・ピン
過熱保護