SBOS729B October   2015  – October 2025 DRV425

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Fluxgate Sensor Front-End
        1. 6.3.1.1 Fluxgate Sensor
        2. 6.3.1.2 Bandwidth
        3. 6.3.1.3 Differential Driver for the Internal Compensation Coil
        4. 6.3.1.4 Magnetic Field Range, Overrange Indicator, and Error Flag
      2. 6.3.2 Shunt-Sense Amplifier
      3. 6.3.3 Voltage Reference
      4. 6.3.4 Low-Power Operation
    4. 6.4 Device Functional Modes
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Applications
      1. 7.2.1 Linear Position Sensing
        1. 7.2.1.1 Design Requirements
        2. 7.2.1.2 Detailed Design Procedure
        3. 7.2.1.3 Application Curves
      2. 7.2.2 Current Sensing in Busbars
        1. 7.2.2.1 Design Requirements
        2. 7.2.2.2 Detailed Design Procedure
        3. 7.2.2.3 Application Curves
    3. 7.3 Power Supply Recommendations
      1. 7.3.1 Power Supply Decoupling
      2. 7.3.2 Power-On Start-Up and Brownout
      3. 7.3.3 Power Dissipation
        1. 7.3.3.1 Thermal Pad
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
      2. 7.4.2 Layout Example
  9. 8 Device and Documentation Support
    1. 8.1 Documentation Support
      1. 8.1.1 Related Documentation
    2. 8.2 Receiving Notification of Documentation Updates
    3. 8.3 Support Resources
    4. 8.4 Receiving Notification of Documentation Updates
    5. 8.5 Support Resources
    6. 8.6 Trademarks
    7. 8.7 Electrostatic Discharge Caution
    8. 8.8 Glossary
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

Electrical Characteristics

all minimum and maximum specifications are at TA = 25°C, VDD = 3.0V to 5.5V, and IDRV1 = IDRV2 = 0mA (unless otherwise noted); typical values are at VDD = 5.0V.
PARAMETERTEST CONDITIONSMINTYPMAXUNIT
FLUXGATE SENSOR FRONT-END
OffsetNo magnetic field–8±28µT
Offset driftNo magnetic field±5nT/°C
GGainCurrent at DRV1 and DRV2 outputs12.2mA/mT
Gain error±0.04%
Gain driftBest-fit line method±7ppm/°C
Linearity error0.1%
HysteresisMagnetic field sweep from –10mT to 10mT1.4µT
Noisef = 0.1Hz to 10Hz17nTrms
Noise densityf = 1kHz1.5nT/√ Hz
Compensation range–22mT
Saturation trip level for the
ERROR pin(2)
Open-loop, uncompensated field1.6mT
ERROR delayOpen-loop at B > 1.6mT4 to 6µs
BWBandwidthBSEL = 0, RSHUNT = 22Ω32kHz
BSEL = 1, RSHUNT = 22Ω47
IOSShort-circuit currentVDD = 5V250mA
VDD = 3.3V150
Common-mode output voltage at the DRV1 and DRV2 pinsVREFOUTV
Compensation coil resistance100Ω
SHUNT-SENSE AMPLIFIER
VOOOutput offset voltageVAINP = VAINN = VREFIN, VDD = 3.0V–0.075±0.010.075mV
Output offset voltage drift–2±0.42µV/°C
CMRRCommon-mode rejection ratio, RTO(1)VCM = –1V to VDD + 1V, VREFIN = VDD / 2–250±50250µV/V
PSRRAMPPower-supply rejection ratio, RTO(1)VDD = 3.0V to 5.5V, VCM = VREFIN–86±486µV/V
VICRCommon-mode input voltage range–1VDD + 1V
zidDifferential input impedance16.52023.5kΩ
zicCommon-mode input impedance405060kΩ
GnomNominal gainVVOUT / (VAINP – VAINN)4V/V
EGGain error–0.3%±0.02%0.3%
Gain error drift–5±15ppm/°C
Linearity error12ppm
Voltage output swing from negative rail (OR pin trip level)(2)VDD = 5.5V, IVOUT = 2.5mA4885mV
VDD = 3.0V, IVOUT = 2.5mA56100
Voltage output swing from positive rail (OR pin trip level)(2)VDD = 5.5V, IVOUT = –2.5mAVDD – 85VDD – 48mV
VDD = 3.0V, IVOUT = –2.5mAVDD – 100VDD – 56
Signal overrange indication delay
(OR pin)(2)
VIN = 1V step2.5 to 3.5µs
IOSShort-circuit currentVOUT connected to GND–18mA
VOUT connected to VDD20
BW–3dBBandwidth2MHz
SRSlew rate6.5V/µs
tsaSettling timeLarge signalΔV = ± 2V to 1%, no external filter0.9µs
Small signalΔV = ± 0.4V to 0.01%8
enOutput voltage noise densityf = 1kHz, compensation loop disabled170nV/√ Hz
VREFINInput voltage range at pin REFINInput voltage range at REFIN pinGNDVDDV
VOLTAGE REFERENCE
VREFOUTReference output voltage at the REFOUT pinRSEL[1:0] = 00, no load2.452.52.55V
RSEL[1:0] = 01, no load1.61.651.7
RSEL[1:0] = 1x, no load455055% of VDD
Reference output voltage driftRSEL[1:0] = 0x–50±1050ppm/°C
Voltage divider gain error driftRSEL[1:0] = 1x–50±1050ppm/°C
PSRRREFPower-supply rejection ratioRSEL[1:0] = 0x–300±15300µV/V
ΔVO(ΔIO)Load regulationRSEL[1:0] = 0x, load to GND or VDD,
ΔILOAD = 0mA to 5mA, TA = –40°C to +125°C
0.150.35mV/mA
RSEL[1:0] = 1x, load to GND or VDD,
ΔILOAD = 0mA to 5mA, TA = –40°C to +125°C
0.30.8
IOSShort-circuit currentREFOUT connected to VDD20mA
REFOUT connected to GND–18mA
DIGITAL INPUTS/OUTPUTS (CMOS)
IILInput leakage current0.01µA
VIHHigh-level input voltageTA = –40°C to +125°C0.7 × VDDVDD + 0.3V
VILLow-level input voltageTA = –40°C to +125°C–0.30.3 × VDDV
VOHHigh-level output voltageOpen-drain outputSet by external pullup resistorV
VOLLow-level output voltage4mA sink current0.3V
POWER SUPPLY
IQQuiescent currentIDRV1/2 = 0mA, 3.0V ≤ VDD ≤ 3.6V,
TA = –40°C to +125°C
68mA
IDRV1/2 = 0mA, 4.5V ≤ VDD ≤ 5.5V,
TA = –40°C to +125°C
710
VPORPower-on reset threshold2.4V
Parameter value is referred-to-output (RTO).
See the Magnetic Field Range, Overrange Indicator, and Error Flag section for details on the behavior of the ERROR and OR outputs.