SLAAEO5 September   2024 MSPM0C1103 , MSPM0C1103-Q1 , MSPM0C1104 , MSPM0C1104-Q1 , MSPM0C1105 , MSPM0C1106 , MSPM0C1106-Q1 , MSPM0G1105 , MSPM0G1106 , MSPM0G1107 , MSPM0G1505 , MSPM0G1506 , MSPM0G1507 , MSPM0G1518 , MSPM0G1519 , MSPM0G3105 , MSPM0G3105-Q1 , MSPM0G3106 , MSPM0G3106-Q1 , MSPM0G3107 , MSPM0G3107-Q1 , MSPM0G3505 , MSPM0G3505-Q1 , MSPM0G3506 , MSPM0G3506-Q1 , MSPM0G3507 , MSPM0G3507-Q1 , MSPM0G3518 , MSPM0G3518-Q1 , MSPM0G3519 , MSPM0G3519-Q1 , MSPM0H3216 , MSPM0H3216-Q1 , MSPM0L1105

1.   1
2.   Abstract
3.   Trademarks
4. 1Introduction to the Debug Subsystem and MSPM0
   1. 1.1 Access Ports of MSPM0
      1. 1.1.1 Advance High-Performance Bus Access Port
      2. 1.1.2 Configuration Access Port
      3. 1.1.3 Security Access Port
      4. 1.1.4 EnergyTrace Access Port
      5. 1.1.5 Power Access Port
   2. 1.2 Behaviors With the MSPM0 in a Blank/Low-Power State
5. 2Proper SWD Initialization Sequence
6. 3PWR-AP
   1. 3.1 Enabling Low-Power Mode Debugging With MSPM0
   2. 3.2 Modifying the Reset Behavior of MSPM0
      1. 3.2.1 Wait for Debug
      2. 3.2.2 Halt on Reset
      3. 3.2.3 INRST Behavior
   3. 3.3 Register View
7. 4SEC-AP
   1. 4.1 DSSM Commands
      1. 4.1.1 Factory Reset
      2. 4.1.2 Mass Erase
      3. 4.1.3 Password Authentication
      4. 4.1.4 Data Exchange
      5. 4.1.5 Wait for Debug
      6. 4.1.6 Custom DSSM Command
   2. 4.2 DSSM Flow
   3. 4.3 Register View
8. 5Understanding Flash in MSPM0
   1. 5.1 Protection of Flash Memory Across MSPM0
   2. 5.2 Clearing the STATCMD Register
   3. 5.3 Ideal Programming Flow for MSPM0
9. 6The Resets of MSPM0
10. 7Summary
11. 8References

IMPORTANT NOTICE AND DISCLAIMER

TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.

These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources.

TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 

Copyright © 2024, Texas Instruments Incorporated