SLUSEE5E January   2022  – April 2026 TPS4811-Q1

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison Table
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 Recommended Operating Conditions
    3. 6.3 ESD Ratings
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Switching Characteristics
    7. 6.7 Typical Characteristics
  8. 7 Parameter Measurement Information
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Charge Pump and Gate Driver output (VS, PU, PD, BST, SRC)
      2. 8.3.2 Capacitive Load Driving
        1. 8.3.2.1 FET Gate Slew Rate Control
        2. 8.3.2.2 Using Precharge FET - (with TPS48111Q1 Only)
      3. 8.3.3 Overcurrent and Short-Circuit Protection
        1. 8.3.3.1 Overcurrent Protection With Auto-Retry
        2. 8.3.3.2 Overcurrent Protection With Latch-Off
        3. 8.3.3.3 Short-Circuit Protection
      4. 8.3.4 Analog Current Monitor Output (IMON)
      5. 8.3.5 Overvoltage (OV) and Undervoltage Protection (UVLO)
      6. 8.3.6 Remote Temperature sensing and Protection (DIODE)
      7. 8.3.7 Output Reverse Polarity Protection
      8. 8.3.8 TPS4811x-Q1 as a Simple Gate Driver
    4. 8.4 Device Functional Mode (Shutdown Mode)
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application: Driving HVAC PTC Heater Load on KL40 Line in Power Distribution Unit
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Selection of Current Sense Resistor, RSNS
        2. 9.2.2.2 Selection of Scaling Resistor, RSET
        3. 9.2.2.3 Programming the Overcurrent Protection Threshold - RIWRN Selection
        4. 9.2.2.4 Programming the Short-Circuit Protection Threshold - RISCP Selection
        5. 9.2.2.5 Programming the Fault Timer Period - CTMR Selection
        6. 9.2.2.6 Selection of MOSFET, Q1
        7. 9.2.2.7 Selection of Bootstrap Capacitor, CBST
        8. 9.2.2.8 Setting the Undervoltage Lockout and Overvoltage Set Point
        9. 9.2.2.9 Choosing the Current Monitoring Resistor, RIMON
      3. 9.2.3 Application Curves
    3. 9.3 Typical Application: Driving B2B FETs With Pre-Charging the Output Capacitance
      1. 9.3.1 Design Requirements
      2. 9.3.2 External Component Selection
        1. 9.3.2.1 Selection of Pre-Charge Resistor
      3. 9.3.3 Application Curves
    4. 9.4 Typical Application: Designing for EMI
      1. 9.4.1 Common EMI Components
      2. 9.4.2 Programming the Overcurrent Protection Threshold with Added DC Resistance - RIWRN
      3. 9.4.3 Choosing the Current Monitoring Resistor with Added DC Resistance - RIMON
      4. 9.4.4 Programming the Short Circuit Protection Threshold with Added DC Resistance - RISCP
    5. 9.5 Power Supply and EMI Recommendations
    6. 9.6 Layout
      1. 9.6.1 Layout Guidelines
      2. 9.6.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Receiving Notification of Documentation Updates
    2. 10.2 Support Resources
    3. 10.3 Trademarks
    4. 10.4 Electrostatic Discharge Caution
    5. 10.5 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

9.2.2.6 Selection of MOSFET, Q1

For selecting the MOSFET Q1, important electrical parameters are the maximum continuous drain current ID, the maximum drain-to-source voltage VDS(MAX), the maximum drain-to-source voltage VGS(MAX), and the drain-to-source ON resistance RDSON.

The maximum continuous drain current, ID, rating must exceed the maximum continuous load current.

The maximum drain-to-source voltage, VDS(MAX), must be high enough to withstand the highest voltage seen in the application. Considering 60V as the maximum application voltage, MOSFETs with VDS voltage rating of 80V is suitable for this application.

The maximum VGS TPS4811Q1 can drive is 13V, so a MOSFET with 15V minimum VGS rating must be selected.

To reduce the MOSFET conduction losses, lowest possible RDS(ON) is preferred.

Based on the design requirements, IPB160N08S4-03ATMA1 is selected and its ratings are:

  • 80V VDS(MAX) and ±20V VGS(MAX)
  • RDS(ON) is 2.6mΩ typical at 10V VGS
  • MOSFET Qg(total) is 86nC