SLVS841G November   2008  – October 2026 TPS2552 , TPS2552-1 , TPS2553 , TPS2553-1

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison Table
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Typical Characteristics
  8. 7 Parameter Measurement Information
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Overcurrent Conditions
      2. 8.3.2 Reverse-Voltage Protection
      3. 8.3.3 FAULT Response
      4. 8.3.4 Undervoltage Lockout (UVLO)
      5. 8.3.5 ENABLE (EN or EN)
      6. 8.3.6 Thermal Sense
      7. 8.3.7 Quick Output Discharge
    4. 8.4 Device Functional Modes
    5. 8.5 Programming
      1. 8.5.1 Programming the Current-Limit Threshold
  10. 9 Application and Implementation
    1. 9.1 Application Information
      1. 9.1.1 Constant-Current vs Latch-Off Operation and Impact on Output Voltage
    2. 9.2 Typical Applications
      1. 9.2.1 Two-Level Current-Limit Circuit
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedures
          1. 9.2.1.2.1 Designing Above a Minimum Current Limit
          2. 9.2.1.2.2 Designing Below a Maximum Current Limit
          3. 9.2.1.2.3 Accounting for Resistor Tolerance
          4. 9.2.1.2.4 Input and Output Capacitance
        3. 9.2.1.3 Application Curves
      2. 9.2.2 Auto-Retry Functionality
        1. 9.2.2.1 Design Requirements
        2. 9.2.2.2 Detailed Design Procedure
      3. 9.2.3 Typical Application as USB Power Switch
        1. 9.2.3.1 Design Requirements
          1. 9.2.3.1.1 USB Power-Distribution Requirements
        2. 9.2.3.2 Detailed Design Procedure
          1. 9.2.3.2.1 Universal Serial Bus (USB) Power-Distribution Requirements
    3. 9.3 Power Supply Recommendations
      1. 9.3.1 Self-Powered and Bus-Powered Hubs
      2. 9.3.2 Low-Power Bus-Powered and High-Power Bus-Powered Functions
      3. 9.3.3 Power Dissipation and Junction Temperature
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Device Support
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 Support Resources
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

Pin Configuration and Functions

TPS2552 TPS2552-1 TPS2553 TPS2553-1 TPS255x
                             DBV Package
                            6-Pin SOT-23 Top View
EN = Active Low for the TPS2552
EN = Active High for the TPS2553
Add –1 to part number for latch-off version
Add 0 to part number for QOD version
Figure 5-1 TPS255x DBV Package 6-Pin SOT-23 Top View
TPS2552 TPS2552-1 TPS2553 TPS2553-1 TPS255x DRV
                            Package 6-Pin WSON Top View
EN = Active Low for the TPS2552
EN = Active High for the TPS2553
Add –1 to part number for latch-off version
Add 0 to part number for QOD version
Figure 5-2 TPS255x DRV Package 6-Pin WSON Top View
Table 5-1 Pin Functions
PINTYPE(1)DESCRIPTION
NAMETPS2552TPS2553
SOT-23WSONSOT-23WSON
EN34——IEnable input, logic low turns on power switch
EN——34IEnable input, logic high turns on power switch
FAULT4343OActive-low open-drain output, asserted during overcurrent, overtemperature, or reverse-voltage conditions.
GND2525—Ground connection; connect externally to PowerPAD™
ILIM5252O

External resistor used to set current-limit threshold; recommended 15kΩ ≤ RILIM ≤ 232kΩ.

TPS25530-1: 10kΩ ≤ RILIM ≤ 232kΩ.

IN1616IInput voltage; connect a 0.1µF or greater ceramic capacitor from IN to GND as close to the IC as possible.
OUT6161OPower-switch output
PowerPAD—PAD—PAD—Internally connected to GND; used to heat-sink the part to the circuit board traces. Connect PowerPAD to GND pin externally.
I = input, O = output

Add –1 for Latch-Off version

Add 0 to part number for QOD version