SLVSII7 December   2025 TPSM8D7420 , TPSM8D7620

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison Table
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Input Voltage Range (VIN)
      2. 7.3.2  Bias Supply Regulator (VCC)
      3. 7.3.3  Device Configuration Pin (MSEL)
      4. 7.3.4  Multiphase Output Configuration
      5. 7.3.5  Enable and Adjustable UVLO
      6. 7.3.6  Adjustable Switching Frequency
      7. 7.3.7  Device Synchronization (SYNC)
        1. 7.3.7.1 Clock Locking
      8. 7.3.8  Adjustable Output Voltage (FB)
      9. 7.3.9  Control Loop Compensation (COMP)
      10. 7.3.10 Slope Compensation
      11. 7.3.11 Power-Good Output Voltage Monitoring
      12. 7.3.12 Output Discharge
      13. 7.3.13 Soft-Start (SS)
      14. 7.3.14 Overcurrent Protection (OCP)
      15. 7.3.15 Temperature Output
      16. 7.3.16 Thermal Shutdown
    4. 7.4 Device Functional Modes
      1. 7.4.1 Shutdown Mode
      2. 7.4.2 Standby Mode
      3. 7.4.3 Active Mode
        1. 7.4.3.1 Peak Current Mode Operation
        2. 7.4.3.2 Diode Emulation
        3. 7.4.3.3 FPWM Mode Operation
        4. 7.4.3.4 Minimum On-time (High Input Voltage) Operation
        5. 7.4.3.5 Dropout
        6. 7.4.3.6 Recovery from Dropout
  9. 8 Applications and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Applications
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Custom Design With WEBENCH® Tools
        2. 8.2.2.2 Choosing the Switching Frequency
        3. 8.2.2.3 Setting the Output Voltage
        4. 8.2.2.4 Integrated Inductor Considerations
        5. 8.2.2.5 Input Capacitor Selection
        6. 8.2.2.6 VCC and BOOT Capacitors
        7. 8.2.2.7 Output Capacitor Selection
        8. 8.2.2.8 Compensation Selection
      3. 8.2.3 Application Curves
    3. 8.3 2-PH Application
      1. 8.3.1 Design Requirements
      2. 8.3.2 Detailed Design Procedure
      3. 8.3.3 Application Curves 2-PH
    4. 8.4 Power Supply Recommendations
    5. 8.5 Layout
      1. 8.5.1 Layout Guidelines
        1. 8.5.1.1 Thermal Design and Layout
      2. 8.5.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Third-Party Products Disclaimer
      2. 9.1.2 Development Support
        1. 9.1.2.1 Custom Design With WEBENCH® Tools
    2. 9.2 Documentation Support
      1. 9.2.1 Related Documentation
    3. 9.3 Receiving Notification of Documentation Updates
    4. 9.4 Support Resources
    5. 9.5 Trademarks
    6. 9.6 Electrostatic Discharge Caution
    7. 9.7 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

7.3.8 Adjustable Output Voltage (FB)

The TPSM8D7x20 has an adjustable output voltage range from 0.6V up to a maximum of 11V. Setting the output voltage requires two feedback resistors, designated as RFBT and RFBB. The reference voltage at the feedback (FB) pin is set at 0.6V with a feedback system accuracy over the full junction temperature range of ±0.75% with respect to AGND.

Calculate the value for RFBB using Equation 4 below based on a recommended range for RFBT of 10kΩ to 100kΩ.

Equation 4. R F B B k Ω =   R F B T k Ω V O U T 0.6 - 1  

Note that higher feedback resistances consume less DC current. However, an upper RFBT resistor value higher than 1MΩ renders the feedback path more susceptible to noise. Higher feedback resistances generally require more careful layout of the feedback path. Make sure to locate the feedback resistors close to the FB and AGND pins, keeping the feedback trace as short as possible (and away from noisy areas of the PCB). See Layout Example guidelines for more detail.