SLVSJY3A August   2026  – October 2026 BQ25350

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Power-On-Reset (POR)
      2. 6.3.2 Device Power Up from Battery
      3. 6.3.3 Device Power Up from Input Source
        1. 6.3.3.1 Input Voltage Limit Threshold Setting (VINDPM Threshold)
        2. 6.3.3.2 Converter Power-Up
        3. 6.3.3.3 Maximum Power Point Tracking for Small PV Panel
        4. 6.3.3.4 Switching Frequency and Dithering Feature
      4. 6.3.4 Power Path Management
        1. 6.3.4.1 Narrow VDC Architecture
        2. 6.3.4.2 Dynamic Power Management
        3. 6.3.4.3 High Impedance (HIZ) Mode
      5. 6.3.5 Battery Charging Management
        1. 6.3.5.1 Autonomous Charging Cycle
        2. 6.3.5.2 Battery Charging Profile
        3. 6.3.5.3 Charging Termination
        4. 6.3.5.4 BATFET Partition
        5. 6.3.5.5 IR Compensation
        6. 6.3.5.6 Thermistor Qualification
          1. 6.3.5.6.1 Temperature Profile in Charge Mode
          2. 6.3.5.6.2 JEITA Charge Rate Scaling
        7. 6.3.5.7 Charging Safety Timers
      6. 6.3.6 Interrupt to Host (INT)
      7. 6.3.7 BATFET Control
        1. 6.3.7.1 Shutdown Mode
        2. 6.3.7.2 System Power Reset
        3. 6.3.7.3 Standby Mode
      8. 6.3.8 Protections
        1. 6.3.8.1 Voltage and Current Monitoring in Battery Only and HIZ Modes
          1. 6.3.8.1.1 Battery Overcurrent Protection
          2. 6.3.8.1.2 Battery Undervoltage Lockout
        2. 6.3.8.2 Voltage and Current Monitoring in Forward Mode
          1. 6.3.8.2.1 Input Overvoltage
          2. 6.3.8.2.2 System Overvoltage Protection (SYSOVP)
          3. 6.3.8.2.3 Forward Converter Cycle-by-Cycle Current Limit
          4. 6.3.8.2.4 System Short
          5. 6.3.8.2.5 Battery Overvoltage Protection (BATOVP)
        3. 6.3.8.3 Thermal Regulation and Thermal Shutdown
          1. 6.3.8.3.1 Thermal Protection in Battery-only Mode
          2. 6.3.8.3.2 Thermal Protection in Forward Mode
    4. 6.4 Device Functional Modes
      1. 6.4.1 Host Mode and Default Mode
      2. 6.4.2 Register Bit Reset
    5. 6.5 Programming
      1. 6.5.1 Serial Interface
        1. 6.5.1.1 Data Validity
        2. 6.5.1.2 START and STOP Conditions
        3. 6.5.1.3 Byte Format
        4. 6.5.1.4 Acknowledge (ACK) and Not Acknowledge (NACK)
        5. 6.5.1.5 Target Address and Data Direction Bit
        6. 6.5.1.6 Single Write and Read
        7. 6.5.1.7 Multi-Write and Multi-Read
      2. 6.5.2 Register Maps
        1. 6.5.2.1 BQ25350 Registers
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Application
      1. 7.2.1 Design Requirements
      2. 7.2.2 Application Curves
    3. 7.3 Power Supply Recommendations
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
      2. 7.4.2 Layout Example
  9. 8 Device and Documentation Support
    1. 8.1 Receiving Notification of Documentation Updates
    2. 8.2 Support Resources
    3. 8.3 Trademarks
    4. 8.4 Electrostatic Discharge Caution
    5. 8.5 Glossary
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information
    1.     PACKAGE OPTION ADDENDUM
    2. 10.1 Tape and Reel Information
    3. 10.2 Mechanical Data

Mechanical, Packaging, and Orderable Information

The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation.