SPRAD66B February   2023  – December 2024 AM62A1-Q1 , AM62A3 , AM62A3-Q1 , AM62A7 , AM62A7-Q1 , AM62D-Q1 , AM62P , AM62P-Q1

1.   1
2.    AM62Ax, AM62Px, AM62Dx LPDDR4 Board Design and Layout Guidelines
3.   Trademarks
4. 1Overview
   1. 1.1 Board Designs Supported
   2. 1.2 General Board Layout Guidelines
   3. 1.3 PCB Stack-Up
   4. 1.4 Bypass Capacitors
      1. 1.4.1 Bulk Bypass Capacitors
      2. 1.4.2 High-Speed Bypass Capacitors
   5. 1.5 Velocity Compensation
5. 2LPDDR4 Board Design and Layout Guidance
   1. 2.1  LPDDR4 Introduction
   2. 2.2  LPDDR4 Device Implementations Supported
   3. 2.3  LPDDR4 Interface Schematics
   4. 2.4  Compatible JEDEC LPDDR4 Devices
   5. 2.5  Placement
   6. 2.6  LPDDR4 Keepout Region
   7. 2.7  Net Classes
   8. 2.8  LPDDR4 Signal Termination
   9. 2.9  LPDDR4 VREF Routing
   10. 2.10 LPDDR4 VTT
   11. 2.11 CK and ADDR_CTRL Topologies
   12. 2.12 Data Group Topologies
   13. 2.13 CK0 and ADDR_CTRL Routing Specification
   14. 2.14 Data Group Routing Specification
   15. 2.15 Channel, Byte, and Bit Swapping
   16. 2.16 Data Bus Inversion
6. 3LPDDR4 Board Design Simulations
   1. 3.1 Board Model Extraction
   2. 3.2 Board-Model Validation
   3. 3.3 S-Parameter Inspection
   4. 3.4 Time Domain Reflectometry (TDR) Analysis
   5. 3.5 System Level Simulation
      1. 3.5.1 Simulation Setup
      2. 3.5.2 Simulation Parameters
      3. 3.5.3 Simulation Targets
         1. 3.5.3.1 Eye Quality
         2. 3.5.3.2 Delay Report
         3. 3.5.3.3 Mask Report
   6. 3.6 Design Example
      1. 3.6.1 Stack-Up
      2. 3.6.2 Routing
      3. 3.6.3 Model Verification
      4. 3.6.4 Simulation Results
7. 4Additional Information: SOC Package Delays
8. 5Summary
9. 6References
10. 7Revision History

IMPORTANT NOTICE AND DISCLAIMER

TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.

These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources.

TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 

Copyright © 2024, Texas Instruments Incorporated