SPVA024A June   2025  – October 2026 ADC810-Q1

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  POR
    6. 5.6  Timing Characteristics
    7. 5.7  Analog/Digital IO
      1. 5.7.1  Electrical Characteristics
      2. 5.7.2 Switching Characteristics
    8. 5.8  ADC
      1. 5.8.1 Electrical Characteristics
      2. 5.8.2 Linearity Parameters
      3. 5.8.3 Switching Characteristics
    9. 5.9  VREF
      1. 5.9.1 Electrical Characteristics
      2. 5.9.2 Voltage Characteristics
    10. 5.10 I2C
      1. 5.10.1 I2C Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagrams
    3. 6.3 Feature Description
      1. 6.3.1 Multiplexer
      2. 6.3.2 Voltage Reference
      3. 6.3.3 Oscillator
      4. 6.3.4 Output Data Rate and Conversion Time
      5. 6.3.5 Digital Comparator
      6. 6.3.6 Conversion Ready Pin
      7. 6.3.7 Interrupt Output (INT)
    4. 6.4 Device Functional Modes
      1. 6.4.1 Reset and Power-Up
      2. 6.4.2 Operating Modes
        1. 6.4.2.1 Single-Shot Mode
        2. 6.4.2.2 Continuous-Conversion Mode
    5. 6.5 Programming
      1. 6.5.1 I2C Interface
        1. 6.5.1.1 I2C Address Selection
        2. 6.5.1.2 I2C General Call
        3. 6.5.1.3 I2C Speed Modes
      2. 6.5.2 Target Mode Operations
        1. 6.5.2.1 Receive Mode
        2. 6.5.2.2 Transmit Mode
      3. 6.5.3 Writing To and Reading From the Registers
      4. 6.5.4 Data Format
  8. 7 Register Map
  9. 8 Application and Implementation
    1. 8.1 Typical Application
      1. 8.1.1 Schematic
      2. 8.1.2 ADC Configuration Examples
      3. 8.1.3 GPIO Configuration Example
  10. 9 Device and Documentation Support
    1. 9.1 Device Nomenclature
    2. 9.2 Documentation Support
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

Digital Comparator

The ADC810-Q1 features a programmable digital comparator that can issue an alert on the ALERT/RDY pin. The COMP_MODE bit in the ADC Configuration register configures the comparator as either a traditional comparator or a window comparator. In traditional comparator mode, the ALERT/RDY pin asserts (active low by default) when conversion data exceeds the limit set in the high-threshold register (High_thresh). The comparator then deasserts only when the conversion data falls below the limit set in the low-threshold register (Low_thresh). In window comparator mode, the ALERT/RDY pin asserts when the conversion data exceed the High_thresh register or fall below the Low_thresh register value.

In either window or traditional comparator mode, the comparator can be configured to latch after being asserted by the COMP_LAT bit in the ADC Configuration register. This setting causes the assertion to remain even if the input signal is not beyond the bounds of the threshold registers. This latched assertion can only be cleared by reading the ADC Conversion register. The ALERT/RDY pin can be configured as active high or active low by the COMP_POL bit in the ADC Configuration register. Operational diagrams for both the comparator modes are shown in Figure 6-3.

The comparator can also be configured to activate the ALERT/RDY pin only after a set number of successive readings exceed the threshold values set in the threshold registers (High_thresh and Low_thresh). The COMP_QUE[1:0] bits in the ADC Configuration register configures the comparator to wait for one, two, or four readings beyond the threshold before activating the ALERT/RDY pin. The COMP_QUE[1:0] bits can also disable the comparator function, and put the ALERT/RDY pin into high-impedance.

ADC810 ADC810-Q1 ALERT Pin Timing DiagramFigure 6-3 ALERT Pin Timing Diagram