SWRS349A June   2026  – July 2026 CC2340R5MODA

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Functional Block Diagram
  6. 5 Device Comparison
  7. 6 Pin Configurations and Functions
    1. 6.1 Pin Diagrams
      1. 6.1.1 Pin Diagram - MHA Package (Top View)
    2.     10
    3. 6.2 Signal Descriptions
      1.      12
      2.      13
      3.      14
      4.      15
      5.      16
      6.      17
      7.      18
      8.      19
      9.      20
      10.      21
      11.      22
      12.      23
      13.      24
      14.      25
      15.      26
      16.      27
    4. 6.3 Connections for Unused Pins and Modules
  8. 7 Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  DCDC
    5. 7.5  Global LDO (GLDO)
    6. 7.6  Power Supply and Modules
    7. 7.7  Battery Monitor
    8. 7.8  Temperature Sensor
    9. 7.9  Power Consumption - Power Modes
    10. 7.10 Power Consumption - Radio Modes
    11. 7.11 Nonvolatile (Flash) Memory Characteristics
    12. 7.12 Thermal Resistance Characteristics
    13. 7.13 RF Frequency Bands
    14. 7.14 Bluetooth Low Energy - Receive (RX)
    15. 7.15 Bluetooth Low Energy - Transmit (TX)
    16. 7.16 2.4GHz RX/TX CW
    17. 7.17 Timing and Switching Characteristics
      1. 7.17.1 Reset Timing
      2. 7.17.2 Wakeup Timing
      3. 7.17.3 Clock Specifications
        1. 7.17.3.1 48MHz Crystal Oscillator (HFXT)
        2. 7.17.3.2 48MHz RC Oscillator (HFOSC)
        3. 7.17.3.3 32kHz Crystal Oscillator (LFXT)
        4. 7.17.3.4 32kHz RC Oscillator (LFOSC)
    18. 7.18 Peripheral Characteristics
      1. 7.18.1 UART
        1. 7.18.1.1 UART Characteristics
      2. 7.18.2 SPI
        1. 7.18.2.1 SPI Characteristics
        2. 7.18.2.2 SPI Controller Mode
        3. 7.18.2.3 SPI Timing Diagrams - Controller Mode
        4. 7.18.2.4 SPI Peripheral Mode
        5. 7.18.2.5 SPI Timing Diagrams - Peripheral Mode
      3. 7.18.3 I2C
        1. 7.18.3.1 I2C
        2. 7.18.3.2 I2C Timing Diagram
      4. 7.18.4 GPIO
        1. 7.18.4.1 GPIO DC Characteristics
      5. 7.18.5 ADC
        1. 7.18.5.1 Analog-to-Digital Converter (ADC) Characteristics
      6. 7.18.6 Comparators
        1. 7.18.6.1 Ultra-low power comparator
    19. 7.19 Typical Characteristics
      1. 7.19.1 MCU Current
      2. 7.19.2 RX Current
      3. 7.19.3 TX Current
      4. 7.19.4 RX Performance
      5. 7.19.5 TX Performance
      6. 7.19.6 ADC Performance
  9. 8 Detailed Description
    1. 8.1  Overview
    2. 8.2  System CPU
    3. 8.3  Radio (RF Core)
      1. 8.3.1 Bluetooth Low Energy
    4. 8.4  Memory
    5. 8.5  Cryptography
    6. 8.6  Timers
    7. 8.7  Serial Peripherals and I/O
    8. 8.8  Battery and Temperature Monitor
    9. 8.9  µDMA
    10. 8.10 Debug
    11. 8.11 Power Management
    12. 8.12 Clock Systems
    13. 8.13 Network Processor
    14. 8.14 Device Certification and Qualification
      1. 8.14.1 FCC Certification and Statement
      2. 8.14.2 IC/ISED Certification and Statement
      3. 8.14.3 ETSI/CE Certification
      4. 8.14.4 MIC Certification
      5. 8.14.5 Korea Certification
      6. 8.14.6 NCC Certification and Statement
    15. 8.15 Module Markings
    16. 8.16 End Product Labeling
    17. 8.17 Manual Information to the End User
  10. 9 Application, Implementation, and Layout
    1. 9.1 Typical Application Circuit
    2. 9.2 Device Connections
      1. 9.2.1 Unused Pins
    3. 9.3 PCB Layout Guidelines
      1. 9.3.1 General Layout Recommendations
        1. 9.3.1.1 Typical RF Layout Recommendations with Integrated Antenna
        2. 9.3.1.2 RF Layout Recommendations with External Antenna
    4. 9.4 Reference Designs
  11. 10Environmental Requirements and SMT Specifications
    1. 10.1 PCB Bending
    2. 10.2 Handling Environment
      1. 10.2.1 Terminals
      2. 10.2.2 Falling
    3. 10.3 Storage Condition
      1. 10.3.1 Moisture Barrier Bag Before Opened
      2. 10.3.2 Moisture Barrier Bag Open
    4. 10.4 PCB Assembly Guide
      1. 10.4.1 PCB Land Pattern & Thermal Vias
      2. 10.4.2 SMT Assembly Recommendations
      3. 10.4.3 PCB Surface Finish Requirements
      4. 10.4.4 Solder Stencil
      5. 10.4.5 Package Placement
      6. 10.4.6 Solder Joint Inspection
      7. 10.4.7 Rework and Replacement
      8. 10.4.8 Solder Joint Voiding
    5. 10.5 Baking Conditions
    6. 10.6 SMT Recommendations
  12. 11Device and Documentation Support
    1. 11.1 Device Nomenclature
    2. 11.2 Tools and Software
      1. 11.2.1 SimpleLink™ Microcontroller Platform
    3. 11.3 Documentation Support
    4. 11.4 Support Resources
    5. 11.5 Trademarks
    6. 11.6 Electrostatic Discharge Caution
    7. 11.7 Glossary
  13. 12Revision History
  14. 13Mechanical, Packaging, and Orderable Information

9.3.1.1 Typical RF Layout Recommendations with Integrated Antenna

It is critical that the RF section be laid out correctly to make sure optimal module performance. A poor layout can cause low-output power and sensitivity degradation. Figure 9-2 shows the RF placement and routing of the CC2340R5MODA module with the 2.4-GHz integrated antenna.

CC2340R5MODA Module Layout Guidelines Figure 9-2 Module Layout Guidelines

Follow these RF layout recommendations for the CC2340R5MODA module when using the integrated Antenna:

  • Dimensions A, B & C in Figure 9-2 should be at least 20mm for optimal antenna efficiency. These dimensions can be reduced for compact layout designs but then the antenna efficiency will be reduced. With A and B dimensions at 20mm, the antenna efficiency will be around 50%. If A and B are reduced to 15mm; then the expected antenna efficiency will be around 25%. If A and B are reduced to 10mm; then the expected antenna efficiency will be around 10%. It is not recommended to have A or B dimensions less than 10mm.

  • Components Z60, Z61 & Z62 are for antenna matching purposes. The optimum antenna match values for Z60, Z61 & Z62 will be dependent on the layout, final product casing and material, and size of the GND plane. For the Launchpad ref design, Z60: DNM, Z61: 0 ohm & Z62 is 1pF. It is always recommended to use a pi-filter (Z60, Z61 & Z62) for the antenna matching for flexibility to match the antenna and to minimize mismatch losses.

  • It is not recommended to have A or B dimensions less than 10mm in Figure 9-2
  • There must be at least a ground-reference plane under the module on the main PCB