Home Energiemanagement DC/DC-Schaltregler DC/DC-Controller
Home
Energiemanagement
DC/DC-Schaltregler
DC/DC-Controller
NEU

LM851772-Q1

VORSCHAU

Abwärts-/Aufwärtswandler für USB-PD in der Automobilindustrie mit 4 Schaltern und I2C-Schnittstelle,

Jetzt bestellen
Datenblatt

LM851772-Q1

VORSCHAU
Datenblatt Jetzt bestellen

Produktdetails

Rating Automotive Topology Buck-Boost Vin (max) (V) 80 Vin (min) (V) 3.5 Vout (max) (V) 55 Vout (min) (V) 1 Features 1% accuracy, AEC Q100, Adjustable current limit, Adjustable soft start, Adjustable switching frequency, Advanced power saving, Dynamic voltage scaling, Enable, Extended power range, Frequency synchronization, I2C, Light-load efficiency, Load Disconnect, Power good, Spread Spectrum, Synchronous rectification, Tracking, USB C/PD compatible, UVLO adjustable EMI features Frequency Dithering, Spread Spectrum Duty cycle (max) (%) 100 Iq (typ) (A) 0.000075 Operating temperature range (°C) -40 to 150
Rating Automotive Topology Buck-Boost Vin (max) (V) 80 Vin (min) (V) 3.5 Vout (max) (V) 55 Vout (min) (V) 1 Features 1% accuracy, AEC Q100, Adjustable current limit, Adjustable soft start, Adjustable switching frequency, Advanced power saving, Dynamic voltage scaling, Enable, Extended power range, Frequency synchronization, I2C, Light-load efficiency, Load Disconnect, Power good, Spread Spectrum, Synchronous rectification, Tracking, USB C/PD compatible, UVLO adjustable EMI features Frequency Dithering, Spread Spectrum Duty cycle (max) (%) 100 Iq (typ) (A) 0.000075 Operating temperature range (°C) -40 to 150
VQFN (RHA) 40 36 mm² 6 x 6
  • Input range from 3.5V to 80V
    • Selectable input voltage operation threshold up to 58.5V in 0.5V steps
  • Dynamical Vo programming using I2C from:
    • 3.3V to 48V in 20mV monotonous steps
    • 3.3V up to 23V in 10mV monotonous steps
  • Peak current regulation control with small voltage transition ripple overall operating modes
  • Shut down quiescent current 3µA
  • Operating quiescent current 75µA
  • Drive (DRV) pin for dual role port power path
    • Push-Pull output for fast pMOS FET control
    • Configurable as charge pump driver stage for nMOS FET
  • Operation mode selection for high efficiency in light load and high load conditions:
    • Power save mode (Single Pulse/µSleep)
    • Automatic conduction mode
  • Integrated high voltage supply LDO
  • Auxiliary high voltage LDO for microcontroller supply
  • Integrated full-bridge gate drive
    • 2A peak current capability
    • Bootstrap over and undervoltage protection
    • Integrated boot-strap diode
  • Fixed frequency independent from operating mode (boost, buck-boost, buck)
    • Forced PWM mode selectable
    • Switching frequency from 100kHz to 2200kHz
    • External clock synchronization and clock output
  • Spread spectrum operation selectable
  • Average input or output current sensor
    • Programmable from 0.5A to 7A in 50mA steps
  • I2C programmable with diagnostics
  • Automotive temperature range (Tj = -40°C to 150°C)
  • 40-Pin WSON package with wettable flanks
  • Functional Safety-Capable
  • Input range from 3.5V to 80V
    • Selectable input voltage operation threshold up to 58.5V in 0.5V steps
  • Dynamical Vo programming using I2C from:
    • 3.3V to 48V in 20mV monotonous steps
    • 3.3V up to 23V in 10mV monotonous steps
  • Peak current regulation control with small voltage transition ripple overall operating modes
  • Shut down quiescent current 3µA
  • Operating quiescent current 75µA
  • Drive (DRV) pin for dual role port power path
    • Push-Pull output for fast pMOS FET control
    • Configurable as charge pump driver stage for nMOS FET
  • Operation mode selection for high efficiency in light load and high load conditions:
    • Power save mode (Single Pulse/µSleep)
    • Automatic conduction mode
  • Integrated high voltage supply LDO
  • Auxiliary high voltage LDO for microcontroller supply
  • Integrated full-bridge gate drive
    • 2A peak current capability
    • Bootstrap over and undervoltage protection
    • Integrated boot-strap diode
  • Fixed frequency independent from operating mode (boost, buck-boost, buck)
    • Forced PWM mode selectable
    • Switching frequency from 100kHz to 2200kHz
    • External clock synchronization and clock output
  • Spread spectrum operation selectable
  • Average input or output current sensor
    • Programmable from 0.5A to 7A in 50mA steps
  • I2C programmable with diagnostics
  • Automotive temperature range (Tj = -40°C to 150°C)
  • 40-Pin WSON package with wettable flanks
  • Functional Safety-Capable

The LM851772-Q1 is a four switch buck-boost controller. The device provides a regulated output voltage if the input voltage is higher, equal or lower than the adjusted output voltage. In power save mode the device supports very high efficiency over the complete operation range of the output. The output voltage and average current is dynamically programmable using the integrated I2C interface. The configuration range for output voltage and average current meets the USB-PD standard requirements. The integrated DRV pin is used to control an optional disconnect FET if the system is targeted to support dual role port (DRP) requirements.

LM851772-Q1 runs at a fixed switching frequency, which is set using the RT/SYNC pin. The switching frequency remains the same during buck, boost and buck-boost operation. The device maintains small mode transition ripple over all operating modes.

The LM851772-Q1 is a four switch buck-boost controller. The device provides a regulated output voltage if the input voltage is higher, equal or lower than the adjusted output voltage. In power save mode the device supports very high efficiency over the complete operation range of the output. The output voltage and average current is dynamically programmable using the integrated I2C interface. The configuration range for output voltage and average current meets the USB-PD standard requirements. The integrated DRV pin is used to control an optional disconnect FET if the system is targeted to support dual role port (DRP) requirements.

LM851772-Q1 runs at a fixed switching frequency, which is set using the RT/SYNC pin. The switching frequency remains the same during buck, boost and buck-boost operation. The device maintains small mode transition ripple over all operating modes.
filter Andere DC/DC-Controller suchen
Herunterladen Video mit Transkript ansehen Video

Technische Dokumentation

star =Von TI ausgewählte Top-Empfehlungen für dieses Produkt
Keine Ergebnisse gefunden. Bitte geben Sie einen anderen Begriff ein und versuchen Sie es erneut.
Alle anzeigen 1
Top-Dokumentation Typ Titel Format-Optionen Datum
* Data sheet LM851772-Q1 80V VIN 4 Switch Buck-Boost Controller With I2C for USB-PD Sourcing datasheet PDF | HTML 19 Jun 2026

Design und Entwicklung

Weitere Bedingungen oder erforderliche Ressourcen enthält gegebenenfalls die Detailseite, die Sie durch Klicken auf einen der unten stehenden Titel erreichen.

Evaluierungsplatine

LM251772Q1EVM-PD — LM251772-Q1 – Evaluierungsmodul

The LM251772Q1EVM-PD demonstrates a flexible high power buck-boost design using the LM251772-Q1. The evaluation module is configured to operate from an input voltage range of 9V to 36V and to produce a regulated 5V to 48V output with up to a 5A load current. The EVM operates with a switching (...)
Benutzerhandbuch: PDF | HTML
Nicht verfügbar auf TI.com
GUI für Evaluierungsmodul (EVM)

LM851772-CONFIGURATON-GUI — LM851772 GUI for configuration via I2C

Graphical User Interface (GUI) to configure the LM851772 via I2C. You can use the Launch button for using the GUI online via a browser or one of the download files to operate the GUI offline
Unterstützte Produkte und Hardware

Unterstützte Produkte und Hardware
Start Download-Optionen
Berechnungstool

LM851772-QUICKSTART-CALC — LM851772 BuckBoost Quickstart Calculator Tool

LM851772 BuckBoost Quickstart Calculator Tool. This standalone tool facilitates and assists the power supply engineer with the design of a DC/DC buck-boost converter based on the LM851772.
Unterstützte Produkte und Hardware

Unterstützte Produkte und Hardware
Herunterladen
Gehäuse Pins CAD-Symbole, Footprints und 3D-Modelle
VQFN (RHA) 40 Ultra Librarian
Es gelten die allgemeinen Geschäftsbedingungen von TI für Evaluierungsartikel.

Bestellen & Qualität

Beinhaltete Information:
  • RoHS
  • REACH
  • Bausteinkennzeichnung
  • Blei-Finish/Ball-Material
  • MSL-Rating / Spitzenrückfluss
  • MTBF-/FIT-Schätzungen
  • Materialinhalt
  • Qualifikationszusammenfassung
  • Kontinuierliches Zuverlässigkeitsmonitoring
Beinhaltete Information:
  • Werksstandort
  • Montagestandort

Empfohlene Produkte können Parameter, Evaluierungsmodule oder Referenzdesigns zu diesem TI-Produkt beinhalten.

Support und Schulungen

TI E2E™-Foren mit technischem Support von TI-Ingenieuren

Alle Forenthemen auf Englisch anzeigen

Inhalte werden ohne Gewähr von TI und der Community bereitgestellt. Sie stellen keine Spezifikationen von TI dar. Siehe Nutzungsbedingungen.

Bei Fragen zu den Themen Qualität, Gehäuse oder Bestellung von TI-Produkten siehe TI-Support. ​​​​​​​​​​​​​​

Videos