Home Energiemanagement DC/DC-Spannungsversorgungsmodul Stromversorgungsmodule (integrierter Induktor)
Home
Energiemanagement
DC/DC-Spannungsversorgungsmodul
Stromversorgungsmodule (integrierter Induktor)
NEU

TPSM83101L

AKTIV

1.5A high-efficiency buck-boost module with integrated inductor

Jetzt bestellen
Datenblatt

TPSM83101L

AKTIV
Datenblatt Jetzt bestellen

Produktdetails

Rating Catalog Topology Buck-Boost Iout (max) (A) 2 Vin (max) (V) 5.5 Vin (min) (V) 1.6 Vout (max) (V) 5.5 Vout (min) (V) 1.2 Features Enable, Light-load efficiency, Load Disconnect, Synchronous rectification, UVLO fixed Operating temperature range (°C) -40 to 125 Switch current limit (typ) (A) 3 Type Module Duty cycle (max) (%) 100 Switching frequency (min) (kHz) 1800 Switching frequency (max) (kHz) 2200
Rating Catalog Topology Buck-Boost Iout (max) (A) 2 Vin (max) (V) 5.5 Vin (min) (V) 1.6 Vout (max) (V) 5.5 Vout (min) (V) 1.2 Features Enable, Light-load efficiency, Load Disconnect, Synchronous rectification, UVLO fixed Operating temperature range (°C) -40 to 125 Switch current limit (typ) (A) 3 Type Module Duty cycle (max) (%) 100 Switching frequency (min) (kHz) 1800 Switching frequency (max) (kHz) 2200
USIP (SIU) 8 See data sheet
  • 1.6V to 5.5V input voltage range
    • Device input voltage > 1.65V for start-up
  • 1.2V to 5.5V output voltage range
    • 1.0V Vout is supported in PFM mode
  • High output current capability, 3A peak switch current
    • 1.5A Iout for VIN ≥ 3V, VOUT = 3.3V
    • 1.2A Iout for VIN ≥ 2.7V, VOUT = 3.3V
  • Active output discharge (TPSM83101, TPSM83101L only)
  • High efficiency over the entire load range
    • 8µA typical quiescent current
    • Automatic power save mode and forced PWM mode
  • Peak current buck-boost mode architecture
    • Seamless mode transition
    • Forward and reverse current operation
    • Start-up into prebiased outputs
    • Fixed-frequency operation with 2MHz switching
  • Safety and robust operation features
    • Overcurrent protection and short-circuit protection
    • Integrated soft start with active ramp adoption
    • Overtemperature protection and overvoltage protection
    • True shutdown function with load disconnection
    • Forward and backward current limit
  • Small design size
    • MicroSiP™ power module with integrated inductor
    • 2.0mm × 2.6mm × 1.2mm(max) 8-pin µSiP package
  • Create a custom design using the TPSM8310xx device with the WEBENCH® Power Designer
  • 1.6V to 5.5V input voltage range
    • Device input voltage > 1.65V for start-up
  • 1.2V to 5.5V output voltage range
    • 1.0V Vout is supported in PFM mode
  • High output current capability, 3A peak switch current
    • 1.5A Iout for VIN ≥ 3V, VOUT = 3.3V
    • 1.2A Iout for VIN ≥ 2.7V, VOUT = 3.3V
  • Active output discharge (TPSM83101, TPSM83101L only)
  • High efficiency over the entire load range
    • 8µA typical quiescent current
    • Automatic power save mode and forced PWM mode
  • Peak current buck-boost mode architecture
    • Seamless mode transition
    • Forward and reverse current operation
    • Start-up into prebiased outputs
    • Fixed-frequency operation with 2MHz switching
  • Safety and robust operation features
    • Overcurrent protection and short-circuit protection
    • Integrated soft start with active ramp adoption
    • Overtemperature protection and overvoltage protection
    • True shutdown function with load disconnection
    • Forward and backward current limit
  • Small design size
    • MicroSiP™ power module with integrated inductor
    • 2.0mm × 2.6mm × 1.2mm(max) 8-pin µSiP package
  • Create a custom design using the TPSM8310xx device with the WEBENCH® Power Designer

The TPSM83100, TPSM83101, and TPSM83101L are constant frequency peak current mode control buck-boost MicroSiP™ power modules optimized for small design size and high efficiency. The power modules integrate an inductor to simplify design, reduce external components, and save PCB area. The power modules have a 3A peak current limit (typical) and 1.6V to 5.5V input voltage range. The TPSM83100 and TPSM83101, TPSM83101L provide a power supply design for system pre-regulators and voltage stabilizers.

Depending on the input voltage, the TPSM83100 and TPSM83101, TPSM83101L automatically operate in boost, buck, or in 3-cycle buck-boost mode when the input voltage is approximately equal to the output voltage. The transitions between modes happen at a defined duty cycle and avoid unwanted toggling within the modes to reduce output voltage ripple. 8µA quiescent current and power save mode enable the highest efficiency for light to no-load conditions.

The TPSM83100, TPSM83101, and TPSM83101L are constant frequency peak current mode control buck-boost MicroSiP™ power modules optimized for small design size and high efficiency. The power modules integrate an inductor to simplify design, reduce external components, and save PCB area. The power modules have a 3A peak current limit (typical) and 1.6V to 5.5V input voltage range. The TPSM83100 and TPSM83101, TPSM83101L provide a power supply design for system pre-regulators and voltage stabilizers.

Depending on the input voltage, the TPSM83100 and TPSM83101, TPSM83101L automatically operate in boost, buck, or in 3-cycle buck-boost mode when the input voltage is approximately equal to the output voltage. The transitions between modes happen at a defined duty cycle and avoid unwanted toggling within the modes to reduce output voltage ripple. 8µA quiescent current and power save mode enable the highest efficiency for light to no-load conditions.

filter Andere Stromversorgungsmodule (integrierter Induktor) suchen
Herunterladen Video mit Transkript ansehen Video

Technische Dokumentation

star =Von TI ausgewählte Top-Empfehlungen für dieses Produkt
Keine Ergebnisse gefunden. Bitte geben Sie einen anderen Begriff ein und versuchen Sie es erneut.
Alle anzeigen 1
Top-Dokumentation Typ Titel Format-Optionen Datum
* Data sheet TPSM8310xx 1.5A Output Current, Buck-Boost MicroSiP™ Power Module With Integrated Inductor datasheet (Rev. C) PDF | HTML 18 Mär 2026

Design und Entwicklung

Weitere Bedingungen oder erforderliche Ressourcen enthält gegebenenfalls die Detailseite, die Sie durch Klicken auf einen der unten stehenden Titel erreichen.

Gehäuse Pins CAD-Symbole, Footprints und 3D-Modelle
USIP (SIU) 8 Ultra Librarian
Es gelten die allgemeinen Geschäftsbedingungen von TI für Evaluierungsartikel.

Bestellen & Qualität

Beinhaltete Information:
  • RoHS
  • REACH
  • Bausteinkennzeichnung
  • Blei-Finish/Ball-Material
  • MSL-Rating / Spitzenrückfluss
  • MTBF-/FIT-Schätzungen
  • Materialinhalt
  • Qualifikationszusammenfassung
  • Kontinuierliches Zuverlässigkeitsmonitoring
Beinhaltete Information:
  • Werksstandort
  • Montagestandort

Support und Schulungen

TI E2E™-Foren mit technischem Support von TI-Ingenieuren

Alle Forenthemen auf Englisch anzeigen

Inhalte werden ohne Gewähr von TI und der Community bereitgestellt. Sie stellen keine Spezifikationen von TI dar. Siehe Nutzungsbedingungen.

Bei Fragen zu den Themen Qualität, Gehäuse oder Bestellung von TI-Produkten siehe TI-Support. ​​​​​​​​​​​​​​

Videos