Inicio Administración de potencia Reguladores conmutados CC/CC Convertidores de CC/CC

LM2597HV

ACTIVO

Convertidor de potencia SIMPLE SWITCHER y regulador de tensión reductor de 150 kHz y 0.5 A con carac

Se encuentra disponible una versión más nueva de este producto

open-in-new Comparar alternativas
Misma funcionalidad con diferente configuración de pines que el dispositivo comparado
TPSM5601R5H ACTIVO Módulo de potencia de 1.5 A, entrada de 60 V, salida de 1 V a 16 V, encapsulado QFN HotRod™ mejorado Save board space, simplify design and speed time to market with an integrated-inductor power module.
LMR36506 ACTIVO Convertidor buck síncrono ultrapequeño de 3 V a 65 V, 0,6 A con IQ de 4 μA Higher Fsw, better efficiency, lower EMI and lower IQ.

Detalles del producto

Rating Catalog Topology Buck Iout (max) (A) 0.5 Vin (max) (V) 60 Vin (min) (V) 4.5 Vout (max) (V) 37 Vout (min) (V) 3.3 Features Over Current Protection, Power good Control mode Voltage mode Operating temperature range (°C) -40 to 125 Iq (typ) (A) 0.005 Duty cycle (max) (%) 100
Rating Catalog Topology Buck Iout (max) (A) 0.5 Vin (max) (V) 60 Vin (min) (V) 4.5 Vout (max) (V) 37 Vout (min) (V) 3.3 Features Over Current Protection, Power good Control mode Voltage mode Operating temperature range (°C) -40 to 125 Iq (typ) (A) 0.005 Duty cycle (max) (%) 100
SOIC (D) 8 29.4 mm² (4.9 mm × 6 mm) PDIP (P) 8 92.5083 mm² (9.81 mm × 9.43 mm)
  • 3.3-V, 5-V, 12-V, and Adjustable Output Versions
  • Adjustable Version Output Voltage Range: 1.2 V
    to 37 V (57 V for HV Version) ±4% Maximum Over
    Line and Load Conditions
  • Specified 0.5-A Output Current
  • Available in 8-Pin Surface-Mount and 8-Pin PDIP
    Packages
  • Input Voltage Range Up to 60 V
  • 150-kHz Fixed-Frequency Internal Oscillator
  • Shutdown/Soft-Start
  • Out of Regulation Error Flag
  • Error Output Delay
  • Bias Supply Pin (VBS) for Internal Circuitry
    Improves Efficiency at High Input Voltages
  • Low Power Standby Mode, IQ, Typically 85 µA
  • High Efficiency
  • Uses Readily Available Standard Inductors
  • Thermal Shutdown and Current-Limit Protection
  • 3.3-V, 5-V, 12-V, and Adjustable Output Versions
  • Adjustable Version Output Voltage Range: 1.2 V
    to 37 V (57 V for HV Version) ±4% Maximum Over
    Line and Load Conditions
  • Specified 0.5-A Output Current
  • Available in 8-Pin Surface-Mount and 8-Pin PDIP
    Packages
  • Input Voltage Range Up to 60 V
  • 150-kHz Fixed-Frequency Internal Oscillator
  • Shutdown/Soft-Start
  • Out of Regulation Error Flag
  • Error Output Delay
  • Bias Supply Pin (VBS) for Internal Circuitry
    Improves Efficiency at High Input Voltages
  • Low Power Standby Mode, IQ, Typically 85 µA
  • High Efficiency
  • Uses Readily Available Standard Inductors
  • Thermal Shutdown and Current-Limit Protection

The LM2597xx series of regulators are monolithic integrated circuits that provide all the active functions for a step-down (buck) switching regulator, capable of driving a 0.5-A load with excellent line and load regulation. These devices are available in fixed output voltages of 3.3 V, 5 V, 12 V, and an adjustable output version, and are packaged in an 8-pin PDIP and an 8-pin surface-mount package.

This series of switching regulators is similar to the LM2594 series, with additional supervisory and performance features added.

Requiring a minimum number of external components, these regulators are simple to use and include internal frequency compensation, improved line and load specifications, fixed-frequency oscillator, Shutdown/Soft-start, error flag delay, and error flag output.

The LM2597xx series operates at a switching frequency of 150-kHz, thus allowing smaller-sized filter components than what would be required with lower-frequency switching regulators. Because of its high efficiency, the copper traces on the printed-circuit board are normally the only heat sinking required.

A standard series of inductors (both through-hole and surface-mount types) are available from several different manufacturers optimized for use with the LM2597xx series. This feature greatly simplifies the design of switch-mode power supplies.

Other features include a specified ±4% tolerance on output voltage under all conditions of input voltage and output load conditions, and ±15% on the oscillator frequency. External shutdown is included, featuring typically 85-µA standby current. Self protection features include a two stage current limit for the output switch and an overtemperature shutdown for complete protection under fault conditions.

The LM2597HV is for use in applications requiring and input voltage up to 60 V.

The LM2597xx series of regulators are monolithic integrated circuits that provide all the active functions for a step-down (buck) switching regulator, capable of driving a 0.5-A load with excellent line and load regulation. These devices are available in fixed output voltages of 3.3 V, 5 V, 12 V, and an adjustable output version, and are packaged in an 8-pin PDIP and an 8-pin surface-mount package.

This series of switching regulators is similar to the LM2594 series, with additional supervisory and performance features added.

Requiring a minimum number of external components, these regulators are simple to use and include internal frequency compensation, improved line and load specifications, fixed-frequency oscillator, Shutdown/Soft-start, error flag delay, and error flag output.

The LM2597xx series operates at a switching frequency of 150-kHz, thus allowing smaller-sized filter components than what would be required with lower-frequency switching regulators. Because of its high efficiency, the copper traces on the printed-circuit board are normally the only heat sinking required.

A standard series of inductors (both through-hole and surface-mount types) are available from several different manufacturers optimized for use with the LM2597xx series. This feature greatly simplifies the design of switch-mode power supplies.

Other features include a specified ±4% tolerance on output voltage under all conditions of input voltage and output load conditions, and ±15% on the oscillator frequency. External shutdown is included, featuring typically 85-µA standby current. Self protection features include a two stage current limit for the output switch and an overtemperature shutdown for complete protection under fault conditions.

The LM2597HV is for use in applications requiring and input voltage up to 60 V.

Descargar Ver vídeo con transcripción Video

Documentación técnica

No se encontraron resultados. Borre su búsqueda y vuelva a intentarlo.
Ver todo 22
Documentación principal Tipo Título Opciones de formato Descargar la versión más reciente en inglés Fecha
* Hoja de datos LM2597, LM2597HV SIMPLE SWITCHER® Power Converter 150-kHz 0.5-A Step-Down Voltage Regulator With Features datasheet (Rev. D) PDF | HTML 31/05/2016
Nota sobre la aplicación Semiconductor and IC Package Thermal Metrics (Rev. D) PDF | HTML 25/03/2024
Artículo técnico How to increase system reliability and simplify design using DC/DC converters PDF | HTML 13/06/2016
Artículo técnico The importance of accurate switching frequency and current limit when selecting bu PDF | HTML 19/04/2016
Artículo técnico Advantages of leaded packages in robust industrial designs PDF | HTML 8/03/2016
Nota sobre la aplicación Cost-Effective Transformerless Offline Supply for Light Load Applications (Rev. A) 16/06/2015
Nota sobre la aplicación Cap Drop Offline Supply for E-Meters 16/06/2015
Nota sobre la aplicación Low EMI Layout Made SIMPLE With LM43600/1/2/3 and LM46000/1/2 (Rev. A) 12/09/2014
Nota sobre la aplicación AN-2162 Simple Success With Conducted EMI From DC-DC Converters (Rev. C) 24/04/2013
Nota sobre la aplicación AN-1566 Techniques for Thermal Analysis of Switching Power Supply Designs (Rev. A) 23/04/2013
Nota sobre la aplicación AN-2155 Layout Tips for EMI Reduction in DC/ DC Converters (Rev. A) 23/04/2013
Nota sobre la aplicación AN-1229 SIMPLE SWITCHER PCB Layout Guidelines (Rev. C) 23/04/2013
Nota sobre la aplicación AN-1149 Layout Guidelines for Switching Power Supplies (Rev. C) 23/04/2013
Nota sobre la aplicación AN-1889 How to Measure the Loop Transfer Function of Power Supplies (Rev. A) 23/04/2013
Nota sobre la aplicación AN-1081 Low-Cost Low-Parts-Count DC/DC Converter With Multiple Outputs (Rev. B) 23/04/2013
Nota sobre la aplicación AN-1197 Selecting Inductors for Buck Converters (Rev. B) 23/04/2013
Nota sobre la aplicación AN-1246 Stresses in Wide Input DC-DC Converters (Rev. C) 23/04/2013
Nota sobre la aplicación AN-1520 A Guide to Board Layout for Best Thermal Resistance for Exposed Packages (Rev. B) 23/04/2013
Nota sobre la aplicación Simple Techniques Minimize Cross-Coupling in Distributed Power Systems 21/03/2007
Nota sobre la aplicación Input and Output Capacitor Selection 19/09/2005
Más documentación SEM1600 Topic 4: Constructing Your Power Supply – Layout Considerations 12/07/2005
Nota sobre la aplicación AN-643 EMI/RFI Board Design (Rev. B) 3/05/2004

Diseño y desarrollo

Para conocer los términos adicionales o los recursos necesarios, haga clic en cualquier título de abajo para ver la página de detalles cuando esté disponible.

Modelo de simulación

LM2597-ADJ PSpice Transient Model

SNVMAE4.ZIP (74 KB) - Modelo PSpice
Productos y hardware compatibles
Modelo de simulación

LM2597-ADJ Unencrypted PSpice Transient Model

SNVMAE3.ZIP (3 KB) - Modelo PSpice
Productos y hardware compatibles
Encapsulado Pines Símbolos CAD, huellas y modelos 3D
SOIC (D) 8 Ultra Librarian
PDIP (P) 8 Ultra Librarian

Pedidos y calidad

Los productos recomendados pueden tener parámetros, módulos de evaluación o diseños de referencia relacionados con este producto de TI.

Soporte y capacitación

Foros de TI E2E™ con asistencia técnica de los ingenieros de TI

El contenido lo proporcionan “tal como está” TI y los colaboradores de la comunidad y no constituye especificaciones de TI. Consulte los términos de uso.

Si tiene alguna pregunta sobre calidad, encapsulados o pedido de productos de TI, consulte el servicio de asistencia de TI. ​​​​​​​​​​​​​​

Videos