SN74AVC16827

ACTIVO

Búferes de 20 canales, 1.2 V a 3.6 V con salidas de 3 estados

Haga su pedido ahora

Hoja de datos

document-pdfAcrobat 20-Bit Buffer/Driver With 3-State Outputs datasheet (Rev. I) (Inglés)

SN74AVC16827

ACTIVO

Hoja de datos

Haga su pedido ahora

Detalles del producto

Technology family

AVC

Number of channels

20

IOL (max) (mA)

12

Supply current (max) (µA)

40

IOH (max) (mA)

-12

Input type

Standard CMOS

Output type

3-State

Features

Balanced outputs, Over-voltage tolerant inputs, Partial power down (Ioff), Ultra high speed (tpd <5ns)

Rating

Catalog

Operating temperature range (°C)

-40 to 85

Technology family

AVC

Number of channels

20

IOL (max) (mA)

12

Supply current (max) (µA)

40

IOH (max) (mA)

-12

Input type

Standard CMOS

Output type

3-State

Features

Balanced outputs, Over-voltage tolerant inputs, Partial power down (Ioff), Ultra high speed (tpd <5ns)

Rating

Catalog

Operating temperature range (°C)

-40 to 85

TSSOP (DGG)

56

113.4 mm² (14 mm × 8.1 mm)

TVSOP (DGV)

56

72.32 mm² (11.3 mm × 6.4 mm)

Member of the Texas Instruments Widebus^TM Family
EPIC^TM (Enhanced-Performance Implanted CMOS) Submicron Process
DOC^TM (Dynamic Output Control) Circuit Dynamically Changes Output Impedance, Resulting in Noise Reduction Without Speed Degradation
Less Than 2-ns Maximum Propagation Delay at 2.5-V and 3.3-V V_CC
Dynamic Drive Capability Is Equivalent to Standard Outputs With I_OH and I_OL of ±24 mA at 2.5-V V_CC
Overvoltage-Tolerant Inputs/Outputs Allow Mixed-Voltage-Mode Data Communications
I_off Supports Partial-Power-Down Mode Operation
Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II
Package Options Include Plastic Thin Shrink Small-Outline (DGG) and Thin Very Small-Outline (DGV) Packages
DOC, EPIC, and Widebus are trademarks of Texas Instruments.

Member of the Texas Instruments Widebus^TM Family
EPIC^TM (Enhanced-Performance Implanted CMOS) Submicron Process
DOC^TM (Dynamic Output Control) Circuit Dynamically Changes Output Impedance, Resulting in Noise Reduction Without Speed Degradation
Less Than 2-ns Maximum Propagation Delay at 2.5-V and 3.3-V V_CC
Dynamic Drive Capability Is Equivalent to Standard Outputs With I_OH and I_OL of ±24 mA at 2.5-V V_CC
Overvoltage-Tolerant Inputs/Outputs Allow Mixed-Voltage-Mode Data Communications
I_off Supports Partial-Power-Down Mode Operation
Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II
Package Options Include Plastic Thin Shrink Small-Outline (DGG) and Thin Very Small-Outline (DGV) Packages
DOC, EPIC, and Widebus are trademarks of Texas Instruments.

A Dynamic Output Control (DOC) circuit is implemented, which, during the transition, initially lowers the output impedance to effectively drive the load and, subsequently, raises the impedance to reduce noise. Figure 1 shows typical V_OL vs I_OL and V_OH vs I_OH curves to illustrate the output impedance and drive capability of the circuit. At the beginning of the signal transition, the DOC circuit provides a maximum dynamic drive that is equivalent to a high-drive standard-output device. For more information, refer to the TI application reports, AVC Logic Family Technology and Applications, literature number SCEA006, and Dynamic Output Control (DOC^TM) Circuitry Technology and Applications, literature number SCEA009.

This 20-bit noninverting buffer/driver is operational at 1.2-V to 3.6-V V_CC, but is designed specifically for 1.65-V to 3.6-V V_CC operation.

The SN74AVC16827 is composed of two 10-bit sections with separate output-enable signals. For either 10-bit buffer section, the two output-enable (1OE1\ and 1OE2\ or 2OE1\ and 2OE2\) inputs must both be low for the corresponding Y outputs to be active. If either output-enable input is high, the outputs of that 10-bit buffer section are in the high-impedance state.

To ensure the high-impedance state during power up or power down, OE\ should be tied to V_CCthrough a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

This device is fully specified for partial-power-down applications using I_off. The I_off circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down.

The SN74AVC16827 is characterized for operation from -40°C to 85°C.

A Dynamic Output Control (DOC) circuit is implemented, which, during the transition, initially lowers the output impedance to effectively drive the load and, subsequently, raises the impedance to reduce noise. Figure 1 shows typical V_OL vs I_OL and V_OH vs I_OH curves to illustrate the output impedance and drive capability of the circuit. At the beginning of the signal transition, the DOC circuit provides a maximum dynamic drive that is equivalent to a high-drive standard-output device. For more information, refer to the TI application reports, AVC Logic Family Technology and Applications, literature number SCEA006, and Dynamic Output Control (DOC^TM) Circuitry Technology and Applications, literature number SCEA009.

This 20-bit noninverting buffer/driver is operational at 1.2-V to 3.6-V V_CC, but is designed specifically for 1.65-V to 3.6-V V_CC operation.

The SN74AVC16827 is composed of two 10-bit sections with separate output-enable signals. For either 10-bit buffer section, the two output-enable (1OE1\ and 1OE2\ or 2OE1\ and 2OE2\) inputs must both be low for the corresponding Y outputs to be active. If either output-enable input is high, the outputs of that 10-bit buffer section are in the high-impedance state.

To ensure the high-impedance state during power up or power down, OE\ should be tied to V_CCthrough a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

This device is fully specified for partial-power-down applications using I_off. The I_off circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down.

The SN74AVC16827 is characterized for operation from -40°C to 85°C.

filter

Buscar otro/a Búferes y controladores no inversores

Descargar Ver vídeo con transcripción Video

Productos similares que pueden interesarle

open-in-new

Comparar alternativas

Pin por pin con la misma funcionalidad que el dispositivo comparado

SN74ALVCH162836

ACTIVO

Controlador de bus universal de 20 bits con salidas de 3 estados Voltage range 1.65V to 3.6V, average propagation delay 3ns, average drive strength 24mA

SN74ALVCH16827

ACTIVO

Búferes de 20 canales, 1.65 V a 3.6 V con retención de bus y salidas de 3 estados Voltage range 1.65V to 3.6V, average propagation delay 3ns, average drive strength 24mA

SN74ALVCH162721

ACTIVO

Biestable de 20 bits y 3.3 V con salidas de 3 estados Voltage range 1.65V to 3.6V, average propagation delay 3ns, average drive strength 24mA

Documentación técnica

No se encontraron resultados. Borre su búsqueda y vuelva a intentarlo.

Ver todo 1

Documentación principal	Tipo	Título	Opciones de formato	Descargar la versión más reciente en inglés	Fecha
*	Hoja de datos	20-Bit Buffer/Driver With 3-State Outputs datasheet (Rev. I)			29/06/2000

Diseño y desarrollo

Para conocer los términos adicionales o los recursos necesarios, haga clic en cualquier título de abajo para ver la página de detalles cuando esté disponible.

Modelo de simulación