Inicio Administración de potencia Controladores LED Controladores LED de iluminación

TPS61055

ACTIVO

Controlador de LED blanco de 500 mA de alta potencia con interfaz lógica estándar

Se encuentra disponible una versión más nueva de este producto

open-in-new Comparar alternativas
Funcionalidad similar a la del dispositivo comparado
LM36010 ACTIVO Controlador de flash LED de impulso síncrono LM36010 Supports external strobe function.

Detalles del producto

Topology Boost, current mode Vin (min) (V) 2.5 Vin (max) (V) 6 Iout (max) (A) 0.5 Iq (typ) (mA) 8.5 Features Load Disconnect During Shutdown Operating temperature range (°C) -40 to 85 Number of channels 1 Rating Catalog
Topology Boost, current mode Vin (min) (V) 2.5 Vin (max) (V) 6 Iout (max) (A) 0.5 Iq (typ) (mA) 8.5 Features Load Disconnect During Shutdown Operating temperature range (°C) -40 to 85 Number of channels 1 Rating Catalog
VSON (DRC) 10 9 mm² (3 mm × 3 mm)
  • Four Operational Modes
    • Torch and Flash up to ILED = 700 mA
    • Voltage-Regulated Boost Converter: 5.0 V
    • Shutdown: 0.3 µA (Typical)
  • Total Solution Circuit Area < 25 mm2
  • Up to 96% Efficiency
  • Integrated LED Turnon Safety Timer
  • Zero Latency TX-Masking Input
  • Integrated Low Light Dimming Mode
  • LED Disconnect During Shutdown
  • Open/Shorted LED Protection
  • Over-Temperature Protection
  • Available in a 12-Pin NanoFree™ (CSP) and 10-
    Pin VSON Packaging
  • Four Operational Modes
    • Torch and Flash up to ILED = 700 mA
    • Voltage-Regulated Boost Converter: 5.0 V
    • Shutdown: 0.3 µA (Typical)
  • Total Solution Circuit Area < 25 mm2
  • Up to 96% Efficiency
  • Integrated LED Turnon Safety Timer
  • Zero Latency TX-Masking Input
  • Integrated Low Light Dimming Mode
  • LED Disconnect During Shutdown
  • Open/Shorted LED Protection
  • Over-Temperature Protection
  • Available in a 12-Pin NanoFree™ (CSP) and 10-
    Pin VSON Packaging

The TPS6105x device uses a high-frequency synchronous-boost topology with constant current sink to drive single white LEDs. The device uses an inductive fixed-frequency PWM control scheme using small external components, minimizing input ripple current.

The 2-MHz switching frequency allows the use of small and low-profile 2.2-µH inductors. To optimize overall efficiency, the device operates with only a 250-mV LED feedback voltage.

The TPS6105x device not only operates as a regulated current source, but also as a standard voltage-boost regulator. This additional operating mode can be useful to supply other high-power devices in the system, such as a hands-free audio power amplifier, or any other component requiring a supply voltage higher than the battery voltage.

The LED current or the desired output voltage can be programmed through two logic signals (MODE0/1). To simplify flash synchronization with the camera module, the device offers a trigger pin (FLASH_SYNC) for fast LED turnon time.

When the TPS6105x is not in use, it can be put into shutdown mode, reducing the input current to 0.3 µA (typical). During shutdown, the LED pin is high impedance to avoid leakage current through the LED.

The TPS6105x device uses a high-frequency synchronous-boost topology with constant current sink to drive single white LEDs. The device uses an inductive fixed-frequency PWM control scheme using small external components, minimizing input ripple current.

The 2-MHz switching frequency allows the use of small and low-profile 2.2-µH inductors. To optimize overall efficiency, the device operates with only a 250-mV LED feedback voltage.

The TPS6105x device not only operates as a regulated current source, but also as a standard voltage-boost regulator. This additional operating mode can be useful to supply other high-power devices in the system, such as a hands-free audio power amplifier, or any other component requiring a supply voltage higher than the battery voltage.

The LED current or the desired output voltage can be programmed through two logic signals (MODE0/1). To simplify flash synchronization with the camera module, the device offers a trigger pin (FLASH_SYNC) for fast LED turnon time.

When the TPS6105x is not in use, it can be put into shutdown mode, reducing the input current to 0.3 µA (typical). During shutdown, the LED pin is high impedance to avoid leakage current through the LED.

Descargar Ver vídeo con transcripción Video

Documentación técnica

No se encontraron resultados. Borre su búsqueda y vuelva a intentarlo.
Ver todo 6
Documentación principal Tipo Título Opciones de formato Descargar la versión más reciente en inglés Fecha
* Hoja de datos High Power White LED Driver 2-MHz Synchronous Boost Converter datasheet (Rev. B) PDF | HTML 11/09/2015
Informe Common LED Functions and LED Driver Design Considerations 21/09/2020
Nota sobre la aplicación Performing Accurate PFM Mode Efficiency Measurements (Rev. A) 11/12/2018
Guía de selección Power Management Guide 2018 (Rev. R) 25/06/2018
Nota sobre la aplicación Optimizing Transient Response of Internally Compensated DC-DC Converters (Rev. B) 29/11/2017
Nota sobre la aplicación Extending the Soft Start Time Without a Soft Start Pin (Rev. B) 15/06/2017

Diseño y desarrollo

Para conocer los términos adicionales o los recursos necesarios, haga clic en cualquier título de abajo para ver la página de detalles cuando esté disponible.

Encapsulado Pines Símbolos CAD, huellas y modelos 3D
VSON (DRC) 10 Ultra Librarian

Pedidos y calidad

Soporte y capacitación

Foros de TI E2E™ con asistencia técnica de los ingenieros de TI

El contenido lo proporcionan “tal como está” TI y los colaboradores de la comunidad y no constituye especificaciones de TI. Consulte los términos de uso.

Si tiene alguna pregunta sobre calidad, encapsulados o pedido de productos de TI, consulte el servicio de asistencia de TI. ​​​​​​​​​​​​​​

Videos