계산 툴
BQ24600
- 1.2-MHz NMOS-NMOS Synchronous Buck Converter
- Stand-Alone Charger Support for Li-Ion or Li-Polymer
- 5-V – 28-V VCC Input Voltage Range and Supports
1S-6S Battery Cells - Up to 10-A Charge Current and Adapter Current
- High-Accuracy Voltage and Current Regulation
- ±0.5% Charge-Voltage Accuracy
- ±3% Charge-Current Accuracy
- Integration
- Internal Loop Compensation
- Internal Soft Start
- Safety
- Input Overvoltage Protection
- Battery Thermistor Sense Hot/Cold Charge Suspend
- Battery Detection
- Built-In Safety Timer
- Charge Overcurrent Protection
- Battery Short Protection
- Battery Overvoltage Protection
- Thermal Shutdown
- Status Outputs
- Adapter Present
- Charger Operation Status
- Charge Enable Pin
- 6-V Gate Drive for Synchronous Power Converter
- 30-ns Driver Dead-Time and 99.5% Max. Effective Duty Cycle
- 16-Pin 3.5-mm × 3.5-mm QFN package
- Energy Star Low Quiescent Current Iq
- < 15-µA Off-State Battery Discharge Current
- < 1.5-mA Off-State Input Quiescent Current
The bq24600 is a highly integrated Li-ion or Li-polymer switch-mode battery-charge controller. It offers a constant-frequency synchronous PWM controller with high-accuracy charge current and voltage regulation, charge preconditioning, termination, and charge status monitoring,
The bq24600 charges the battery in three phases: preconditioning, constant current, and constant voltage. Charge is terminated when the current reaches a minimum level. An internal charge timer provides a safety backup. The bq24600 automatically restarts the charge cycle if the battery voltage falls below an internal threshold, and enters a low-quiescent-current sleep mode when the input voltage falls below the battery voltage.
기술 문서
검색된 결과가 없습니다. 검색어를 지우고 다시 시도하십시오.
모두 보기4 | 유형 | 직함 | 날짜 | ||
|---|---|---|---|---|
| * | Data sheet | bq24600 Stand-Alone Synchronous Switch-Mode Li-Ion or Li-Polymer Battery Charger with Low Iq datasheet (Rev. B) | PDF | HTML | 2014/11/05 |
| Application note | BQ241xx/BQ246xx Selection of Multi-Cell Standalone Switching Battery Chargers | 2019/12/31 | ||
| Product overview | Battery Management Solutions for Point of Sale Systems | 2014/08/18 | ||
| User guide | Multi Cell Synchronous Switch-Mode Charger, EVM (HPA421) | 2010/02/18 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
평가 보드
BQ24600EVM — BQ24600 멀티 셀 동기 스위치 모드 충전기용 평가 모듈
Evaluation Module for bq24600/bq24620/bq24640. the bq24600 is a highly integrated Li-ion or Li-polymer switch-mode battery charge controller. The bq24620 is highly integrated switch-mode battery charge controller designed specifically to charge Lithium Phosphate battery chemistries. The bq24640 is (...)
사용 설명서: PDF
레퍼런스 디자인
TIDA-00982 — 비군용 드론, 로봇 또는 RC 2S1P 배터리 관리 솔루션 레퍼런스 디자인
This reference design is for a 2S1P battery management solution (BMS) for non-military drone, robot or radio controlled (RC) projects and designs. Quickly add gauging, protection, balancing and charging to any new design for a non-military drone, robot or RC product or use this reference design to (...)
레퍼런스 디자인
PMP10921 — 14V~24Vdc 입력 전압, 3시리즈 셀 리튬 이온 배터리 충전기 레퍼런스 디자인
The PMP10921 reference design uses the BQ24600 Li-Ion synchronous buck controller to charge up to three series cells. It is designed to charge the cells at 0.372A, but can charge at higher currents by changing one resistor. The board area is less than 20mm x 20mm.
레퍼런스 디자인
TIDA-00037 — 멀티 셀 동기 스위치 모드 충전기 레퍼런스 디자인
This reference design, using bq24600, is a highly integrated Li-ion or Li-polymer switch-mode battery charge controller solution. It allows for a highly integrated switch-mode battery charge controller designed specifically to charge Lithium Phosphate battery chemistries. The design contains a (...)
| 패키지 | 핀 | 다운로드 |
|---|---|---|
| VQFN (RVA) | 16 | 옵션 보기 |
주문 및 품질
포함된 정보:
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
포함된 정보:
- 팹 위치
- 조립 위치
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.