코드 예제 또는 데모
CC110L
- RF Performance
- Programmable Output Power up to +12 dBm
- Receive Sensitivity Down to −116 dBm at
0.6 kbps - Programmable Data Rate from 0.6 to 600 kbps
- Frequency Bands: 300–348 MHz,
387–464 MHz, and 779–928 MHz - 2-FSK, 4-FSK, GFSK, MSK, and OOK Supported
- Digital Features
- Flexible Support for Packet Oriented Systems
- On-chip Support for Sync Word Insertion, Flexible Packet Length, and Automatic CRC Calculation
- Low-Power Features
- 200-nA Sleep Mode Current Consumption
- Fast Startup Time; 240 μs From Sleep to RX Mode or TX Mode
- 64-Byte RX and TX FIFO
- Improved Range Using CC1190
- The CC1190 is a Range Extender for
850–950 MHz and is an Ideal Fit for CC110L to Enhance RF Performance - High Sensitivity
- –118 dBm at 1.2 kBaud, 868 MHz, 1% Packet Error Rate
- –120 dBm at 1.2 kBaud, 915 MHz, 1% Packet Error Rate
- +20-dBm Output Power at 868 MHz
- +26-dBm Output Power at 915 MHz
- The CC1190 is a Range Extender for
- General
- Few External Components; Completely On-chip Frequency Synthesizer, No External Filters or RF Switch Needed
- Green Package: RoHS Compliant and No Antimony or Bromine
- Small Size (QLP 4- x 4-mm Package, 20 Pins)
- Suited for Systems Targeting Compliance with EN 300 220 (Europe) and FCC CFR Part 15 (US)
- Support for Asynchronous and Synchronous Serial Transmit Mode for Backward Compatibility with Existing Radio Communication Protocols
The CC110L is a cost optimized sub-1 GHz RF transceiver for the 300–348 MHz, 387–464 MHz, and 779–928 MHz frequency bands. The circuit is based on the popular CC1101 RF transceiver, and RF performance characteristics are identical. Two CC110L transceivers together enable a low-cost bidirectional RF link.
The RF transceiver is integrated with a highly configurable baseband modem. The modem supports various modulation formats and has a configurable data rate up to 600 kbps.
The CC110L provides extensive hardware support for packet handling, data buffering, and burst transmissions.
The main operating parameters and the 64-byte receive and transmit FIFOs of CC110L can be controlled through a serial peripheral interface (SPI). In a typical system, the CC110L will be used together with a microcontroller and a few additional passive components.
기술 문서
검색된 결과가 없습니다. 검색어를 지우고 다시 시도하십시오.
모두 보기11 | 유형 | 직함 | 날짜 | ||
|---|---|---|---|---|
| * | Data sheet | CC110L Value Line Transceiver datasheet (Rev. C) | PDF | HTML | 2016/12/12 |
| * | Errata | CC110L Errata Notes | 2011/05/26 | |
| Selection guide | 무선 연결 기술 선택 가이드 (Rev. B) | 2022/03/07 | ||
| Application note | Debugging Communication Range (Rev. A) | PDF | HTML | 2019/05/23 | |
| White paper | Migrating your proprietary solution to the SimpleLink™ WMCU | 2018/11/07 | ||
| Application note | CC-Antenna-DK2 and Antenna Measurements Summary (Rev. A) | 2017/10/02 | ||
| Application note | CC112x-CC1190 Boost Software Examples | 2015/10/19 | ||
| Application note | TI LPRF EASYMODE | 2014/12/12 | ||
| Application note | Antenna Diversity | 2014/10/23 | ||
| Application note | DN038 -- Miniature Helical PCB Antenna for 868 MHz or 915/920 MHz | 2012/11/27 | ||
| More literature | CC110L BoosterPack Quick Start Guide (Rev. B) | 2011/12/19 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
평가 보드
SMARTRFTRXEBK — SmartRF 트랜시버 평가 보드
The SmartRF Transceiver Evaluation Board (TrxEB) is intended to be used together with Texas Instruments’ low-power RF transceivers for evaluation, performance testing and software development.
The following transceiver evaluation modules are supported:
- CC1101EM*
- CC11xLEM*
- CC112xEM*
- CC1175EM*
- CC1200EM*
- (...)
사용 설명서: PDF
디버그 프로브
CC-DEBUGGER — RF SoC(System-on-Chip)를 위한 디버거이자 프로그래머
The CC Debugger is a small programmer and debugger for the TI Low Power RF System-on-Chips. It can be used together with IAR Embedded Workbench for 8051 (version 7.51A or later) for debugging and SmartRF Flash Programmer for flash programming. The CC Debugger can also be used for controlling (...)
사용 설명서: PDF
인터페이스 어댑터
BOOST-CCEMADAPTER — EM 어댑터 부스터팩
The purpose of the EM adapter board is to provide an-easy-to-use bridge between any of the TI MCU LaunchPads and the wide variety of TI RF evaluation modules (EM), for instance the CCxxxx Low-Power RF evaluation modules. No specific software is provided, so it is up to the user to write the (...)
지원 소프트웨어
PACKET-SNIFFER — SmartRF™ Packet Sniffer 2.18.1
The SmartRF Packet Sniffer is a PC software application that can display and store radio packets captured by a listening RF device. The capture device is connected to the PC via USB. Various RF protocols are supported. The Packet Sniffer filters and decodes packets and displays them in a convenient (...)
지원되는 제품 및 하드웨어
제품
저전력 2.4GHz 제품
Sub-1GHz 무선 MCU
Sub-1 GHz 트랜시버
기타 무선 제품
차량용 무선 커넥티비티 제품
하드웨어 개발
평가 보드
개발 키트
소프트웨어
소프트웨어 프로그래밍 도구
계산 툴
드라이버 또는 라이브러리
지원 소프트웨어
RF-RANGE-ESTIMATOR — RF Range Estimator
This tool is used to calculate a range estimate for indoor and outdoor RF links using TI wireless devices. The outdoor calculation is based upon Line-of-Sight (LOS). For the indoor estimation, construction materials can be selected that are between the Tx and Rx unit. The greater the attenuation (...)
지원되는 제품 및 하드웨어
제품
저전력 2.4GHz 제품
Sub-1GHz 무선 MCU
Sub-1 GHz 트랜시버
차량용 무선 커넥티비티 제품
하드웨어 개발
평가 보드
소프트웨어
계산 툴
지원 소프트웨어
SWRC219 — TrxEB RF PER Test Software
지원되는 제품 및 하드웨어
제품
Sub-1 GHz 트랜시버
하드웨어 개발
개발 키트
계산 툴
SMARTRF-STUDIO-7 — SmartRF Studio
SmartRF™ Studio is a Windows application that helps designers of RF systems to easily evaluate the radio at an early stage in the design process for all TI CC1xxx and CC2xxx low-power RF devices. It simplifies generation of the configuration register values and commands, as well as practical (...)
지원되는 제품 및 하드웨어
제품
MSP430 마이크로컨트롤러
저전력 2.4GHz 제품
Sub-1GHz 무선 MCU
Sub-1 GHz 트랜시버
기타 무선 제품
차량용 무선 커넥티비티 제품
하드웨어 개발
개발 키트
평가 보드
설계 툴
3P-WIRELESS-MODULES — 타사 무선 모듈 검색 툴
타사 무선 모듈 검색 툴은 개발자가 완제품 사양을 충족하는 제품을 식별하고 생산 준비가 완료된 무선 모듈을 조달하는 데 유용합니다. 검색 툴에 포함되어 있는 타사 모듈 공급업체는 TI 무선 연결 제품을 사용하여 무선 모듈을 설계 및 제조하는 전문성을 갖춘 독립 회사입니다.
설계 툴
SIMPLELINK-SUB1GHZ-DESIGN-REVIEWS — SimpleLink™ CC1xxx 장치에 대한 하드웨어 설계 검토
To get started with the SimpleLink™ Sub-1GHz hardware design review process:
- Step 1: Before requesting a review, it is important that to review the technical documentation and design & development resources available on the corresponding product page (see CC1xxx product page links below).
- Step 2: (...)
레퍼런스 디자인
TIDM-LPBP-WIRELESSNODE — 저전력 Sub-1GHz 무선 트랜시버
The Low-Power Sub-1 GHz Wireless Transceiver reference design enables a low cost bi-directional RF link (when using two transceivers). The on-board Anaren Integrated Radio (AIR) A110LR09A radio module with integrated antenna operates in the European 868-870MHz and US 902-928MHz ISM bands. The (...)
레퍼런스 디자인
TIDM-LPBP-EMADAPTER — EM(평가 모듈) 어댑터
This BoosterPack kit contains one "EM Adapter BoosterPack". The purpose of the EM adapter board is to provide an-easy-to-use bridge between any of the TI MCU LaunchPads and the vide variety of TI RF evaluation modules (EM), for instance the CCxxxx Low-Power RF evaluation modules. No specific (...)
회로도: PDF
| 패키지 | 핀 | 다운로드 |
|---|---|---|
| VQFN (RGP) | 20 | 옵션 보기 |
주문 및 품질
포함된 정보:
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
포함된 정보:
- 팹 위치
- 조립 위치
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.