IWRL6432W

활성

웨이퍼 스케일 패키지의 저전력 60GHz 산업용 mmWave 레이더 센서

제품 상세 정보

Type IC Frequency range 57 - 64 GHz Number of receivers 3 Number of transmitters 2 ADC sampling rate (ksps) 12500 TX power (dBm) 11 Arm CPU Arm Cortex-M4F at 160 MHz Hardware accelerators Radar hardware accelerator Edge AI enabled Edge AI Studio enabled, Yes Interface type CAN-FD, I2C, QSPI, SPI, UART RAM (kByte) 1024 Operating temperature range (°C) -40 to 105 TI functional safety category Functional Safety-Capable Power supply solution TPS628501-Q1, TPS628502-Q1 Rating Catalog
Type IC Frequency range 57 - 64 GHz Number of receivers 3 Number of transmitters 2 ADC sampling rate (ksps) 12500 TX power (dBm) 11 Arm CPU Arm Cortex-M4F at 160 MHz Hardware accelerators Radar hardware accelerator Edge AI enabled Edge AI Studio enabled, Yes Interface type CAN-FD, I2C, QSPI, SPI, UART RAM (kByte) 1024 Operating temperature range (°C) -40 to 105 TI functional safety category Functional Safety-Capable Power supply solution TPS628501-Q1, TPS628502-Q1 Rating Catalog
DSBGA (YFF) 111 22.362085 mm² (4.931 mm × 4.535 mm)
  • FMCW Transceiver
    • Integrated PLL, transmitter, receiver, baseband and ADC
    • 57GHz - 64GHz coverage with 7GHz continuous bandwidth
    • 3 receive channels and 2 transmit channels
    • Range typically up to 25m
    • 10dBm typical output power per Tx
    • 12dB Typical noise figure
    • -89dBc/Hz typical phase noise at 1MHz
    • FMCW operation
    • 5MHz IF bandwidth, real-only Rx channels
    • Ultra-accurate chirp engine based on fractional-N PLL
    • Per transmitter binary phase shifter
  • Processing elements
    • Arm M4F core with single precision FPU (160MHz)
    • TI Radar Hardware Accelerator (HWA 1.2) for FFT, log magnitude, and CFAR operations (80MHz)
  • Supports multiple low-power modes
    • Idle mode and deep sleep mode
  • Power management
    • 1.8V and 3.3V IO support
    • Built-in LDO network for enhanced PSRR
    • BOM-Optimized and Power-Optimized modes
    • One or two power rails for 1.8V IO mode, two or three power rails for 3.3V IO mode
  • Built-in calibration
    • Built-in Firmware (ROM)
    • Self-Contained on chip calibration system
  • Host Interface
    • UART
    • CAN-FD
    • SPI
  • RDIF (Radar Data Interface) for raw ADC sample capture
  • Other interfaces available to user application
    • QSPI
    • I2C
    • JTAG
    • GPIOs
    • PWM Interface
  • Internal memory
    • 1MB of On-Chip RAM
    • Configurable L3 shared memory for Radar Cube
    • Data and Code RAM of (512/640/768KB)
  • WCSP package having 11 x 11 BGA grid, 111 BGA balls; Package size: 4.89mm x 4.5mm
  • Clock source
    • 40.0MHz crystal for primary clock
    • Supports externally driven clock (Square/Sine) at 40.0MHz
    • 32kHz internal oscillator for low power operations
  • Supports temperature operating range
    • Operating junction temperature range: –40°C to 105°C
  • FMCW Transceiver
    • Integrated PLL, transmitter, receiver, baseband and ADC
    • 57GHz - 64GHz coverage with 7GHz continuous bandwidth
    • 3 receive channels and 2 transmit channels
    • Range typically up to 25m
    • 10dBm typical output power per Tx
    • 12dB Typical noise figure
    • -89dBc/Hz typical phase noise at 1MHz
    • FMCW operation
    • 5MHz IF bandwidth, real-only Rx channels
    • Ultra-accurate chirp engine based on fractional-N PLL
    • Per transmitter binary phase shifter
  • Processing elements
    • Arm M4F core with single precision FPU (160MHz)
    • TI Radar Hardware Accelerator (HWA 1.2) for FFT, log magnitude, and CFAR operations (80MHz)
  • Supports multiple low-power modes
    • Idle mode and deep sleep mode
  • Power management
    • 1.8V and 3.3V IO support
    • Built-in LDO network for enhanced PSRR
    • BOM-Optimized and Power-Optimized modes
    • One or two power rails for 1.8V IO mode, two or three power rails for 3.3V IO mode
  • Built-in calibration
    • Built-in Firmware (ROM)
    • Self-Contained on chip calibration system
  • Host Interface
    • UART
    • CAN-FD
    • SPI
  • RDIF (Radar Data Interface) for raw ADC sample capture
  • Other interfaces available to user application
    • QSPI
    • I2C
    • JTAG
    • GPIOs
    • PWM Interface
  • Internal memory
    • 1MB of On-Chip RAM
    • Configurable L3 shared memory for Radar Cube
    • Data and Code RAM of (512/640/768KB)
  • WCSP package having 11 x 11 BGA grid, 111 BGA balls; Package size: 4.89mm x 4.5mm
  • Clock source
    • 40.0MHz crystal for primary clock
    • Supports externally driven clock (Square/Sine) at 40.0MHz
    • 32kHz internal oscillator for low power operations
  • Supports temperature operating range
    • Operating junction temperature range: –40°C to 105°C

The IWRL6432W mmWave Sensor device is an integrated single chip mmWave sensor based on FMCW radar technology. The device is capable of operation in the 57GHz to 63.9GHz band and is partitioned into mainly four power domains:

  • RF/Analog Sub-System: This block includes all the RF and Analog components required to transmit and receive the RF signals.
  • Front-End Controller sub-System (FECSS): FECSS contains processor responsible for radar front-end configuration, control, and calibration.
  • Application Sub-System (APPSS): APPSS is where the device implements a user programmable ARM Cortex M4 allowing for custom control and automotive interface applications. Top Sub-System (TOPSS) is part of the APPSS power domain and contains the clocking and power management sub-blocks.
  • Hardware Accelerator (HWA): The HWA block supplements the APPSS by offloading common radar processing such as FFT, Constant False Alarm rate (CFAR), scaling, and compression.

The IWRL6432W is specifically designed to have separate control for each of the above-mentioned power domains to control the states (power ON or OFF) based on use case requirements. The device also features the capability to exercise various low-power states like sleep and deep sleep, where low-power sleep mode is achieved by clock gating and by turning off the internal IP blocks of the device. The device also provides the option of keeping some contents of the device, like Application image or RF profile retained in such scenarios.

Additionally, the device is built with TI’s low power 45nm RF CMOS process and enables unprecedented levels of integration in an extremely small form factor. IWRL6432W is designed for low power, ultra-accurate radar systems in the industrial (and personal electronics) space for applications such as building/factory automation, commercial/residential security, personal electronics, presence/motion detection, and gesture detection/recognition for human machine interfaces

The IWRL6432W mmWave Sensor device is an integrated single chip mmWave sensor based on FMCW radar technology. The device is capable of operation in the 57GHz to 63.9GHz band and is partitioned into mainly four power domains:

  • RF/Analog Sub-System: This block includes all the RF and Analog components required to transmit and receive the RF signals.
  • Front-End Controller sub-System (FECSS): FECSS contains processor responsible for radar front-end configuration, control, and calibration.
  • Application Sub-System (APPSS): APPSS is where the device implements a user programmable ARM Cortex M4 allowing for custom control and automotive interface applications. Top Sub-System (TOPSS) is part of the APPSS power domain and contains the clocking and power management sub-blocks.
  • Hardware Accelerator (HWA): The HWA block supplements the APPSS by offloading common radar processing such as FFT, Constant False Alarm rate (CFAR), scaling, and compression.

The IWRL6432W is specifically designed to have separate control for each of the above-mentioned power domains to control the states (power ON or OFF) based on use case requirements. The device also features the capability to exercise various low-power states like sleep and deep sleep, where low-power sleep mode is achieved by clock gating and by turning off the internal IP blocks of the device. The device also provides the option of keeping some contents of the device, like Application image or RF profile retained in such scenarios.

Additionally, the device is built with TI’s low power 45nm RF CMOS process and enables unprecedented levels of integration in an extremely small form factor. IWRL6432W is designed for low power, ultra-accurate radar systems in the industrial (and personal electronics) space for applications such as building/factory automation, commercial/residential security, personal electronics, presence/motion detection, and gesture detection/recognition for human machine interfaces

다운로드 스크립트와 함께 비디오 보기 비디오

기술 자료

검색된 결과가 없습니다. 검색어를 지우고 다시 시도하세요.
3개 모두 보기
상위 문서 유형 직함 형식 옵션 최신 영어 버전 다운로드 날짜
* 데이터 시트 IWRL6432 WCSP Single-Chip 57 to 64GHz Industrial Radar Sensor datasheet PDF | HTML 2024. 12. 19
* 사용 설명서 AWRL6432, IWRL6432, AWRL1432, IWRL1432 Technical Reference Manual (Rev. C) PDF | HTML 2025. 5. 22
* 정오표 IWRL6432 WCSP Device Silicon Errata (Rev. A) PDF | HTML 2026. 1. 5

설계 및 개발

추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.

평가 보드

IWRL6432BOOST — 단일 칩 60GHz mmWave 저전력 센서용BoosterPack™ 평가 모듈

IWRL6432BOOST는 온보드 FR4 기반 안테나가 포함된 IWRL6432 장치를 기반으로 하는 사용이 편리한 60GHz mmWave 센서 평가 키트입니다. 이 보드를 사용하면 포인트 클라우드 데이터 및 Power-over-USB 인터페이스에 액세스할 수 있습니다. IWRL6432BOOST는 DCA1000EVM 개발 키트에 대한 직접 연결을 지원합니다.

이 키트는 mmWave 도구, 시연, 그리고 mmWave 소프트웨어 개발 키트(MMWAVE-L-SDK) 및 Code ComposerStudio™ IDE(통합 개발 (...)

사용 설명서: PDF | HTML
지원되는 제품 및 하드웨어
재고 있음
제한:
??asset.out-of-stock-ti_ko_KR??
이용할 수 없음
평가 보드

JRJN-3P-MT5C01-02R1 — MT5C01-02R1은 IWRL6432W 장치를 기반으로 하는 60GHz mmWave 레이더 센서 모듈입니다.

MT5C01-02R1은 TI의 산업용 IWRL6432 단일 칩 레이더 기술과 Jorjin의 고급 안테나 설계 기능을 결합한 60GHz mmWave 센서 AOM 모듈입니다.

이 센서 모듈은 고정밀, 소형 폼 팩터와 낮은 소비 전력을 위해 설계된 산업용 IoT 시장에 적합한 솔루션을 제공합니다.

지원되는 제품 및 하드웨어
소프트웨어 개발 키트(SDK)

MMWAVE-L-SDK — mmWave SDK for xWRL6432, IWRL6432AOP, IWRL6432W and xWRL1432

mmWave 저전력 SDK(소프트웨어 개발 키트)는 TI의 저전력 mmWave 센서를 이용한 애플리케이션 평가 및 개발을 지원하는 소프트웨어 패키지 컬렉션입니다. 이 도구에는 고객의 설계 요구를 지원하기 위한 MMWAVE-L-SDK 및 MMWAVE-L-SDK-6 컴패니언 패키지가 포함됩니다.

MMWAVE-L-SDK 및 MMWAVE-L-SDK-6는 mmWave 감지 포트폴리오를 위한 통합형 소프트웨어 플랫폼으로, 간편한 설정과 신속한 기본 작동을 통해 평가 및 개발 환경으로의 빠른 접근을 제공합니다. MMWAVE-L-SDK 및 (...)

지원되는 제품 및 하드웨어
IDE, 구성, 컴파일러 또는 디버거

CCSTUDIO — Code Composer Studio integrated development environment (IDE)

CCStudio™ IDE is part of TI's extensive CCStudio™ development ecosystem and is an integrated development environment for TI's microcontrollers, processors, wireless connectivity devices, and radar sensors. CCStudio IDE is available as desktop or cloud-based applications. The cloud version (...)

지원되는 제품 및 하드웨어
IDE, 구성, 컴파일러 또는 디버거

EDGE-AI-STUDIO — Edge AI Studio

Edge AI Studio는 TI 프로세서, 마이크로컨트롤러, 레이더 센서의 에지 AI 개발을 가속화하기 위해 설계된 그래픽 및 명령줄 툴 모음입니다. TI Model Zoo의 모델을 활용해 개념 증명을 개발하든,
자체 모델을 활용하든, Edge AI Studio는 필요한 모든 툴을 제공합니다.

Edge AI Studio 그래픽 사용자 인터페이스는 라이브 개발 플랫폼에 배포할 모델을 교육 및 컴파일하고, 데이터를 수집하고 데이터에 주석을 추가하기 위한 완전 통합 솔루션을 제공합니다. TI Model Zoo에서 다양한 사전 학습된 (...)

지원되는 제품 및 하드웨어
IDE, 구성, 컴파일러 또는 디버거

EDGE-AI-STUDIO-MCU — Edge AI Studio for Microcontrollers

Edge AI Studio는 TI 프로세서, 마이크로컨트롤러, 레이더 센서의 에지 AI 개발을 가속화하기 위해 설계된 그래픽 및 명령줄 툴 모음입니다. TI Model Zoo의 모델을 활용해 개념 증명을 개발하든,
자체 모델을 활용하든, Edge AI Studio는 필요한 모든 툴을 제공합니다.

Edge AI Studio 그래픽 사용자 인터페이스는 라이브 개발 플랫폼에 배포할 모델을 교육 및 컴파일하고, 데이터를 수집하고 데이터에 주석을 추가하기 위한 완전 통합 솔루션을 제공합니다. TI Model Zoo에서 다양한 사전 학습된 (...)

지원되는 제품 및 하드웨어
온라인 교육

RADAR-ACADEMY — mmWave Radar Academy

The Radar Academy is a documentation package intended to provide educational resources related to mmWave radar technology
지원되는 제품 및 하드웨어
시작하기

TI-DEVELOPER-ZONE — Start embedded development on your desktop or in the cloud

From evaluation to deployment the TI Developer Zone provides a comprehensive range of software, tools and training to ensure that you have everything you need for each stage of the development process.
지원되는 제품 및 하드웨어
평가 모듈(EVM)용 GUI

MMWAVE-SENSING-ESTIMATOR-CLOUD — mmWave sensing estimator cloud development on TI Resource Explorer

The mmWave Sensing Estimator is a web-based configuration tool for TI radar sensors
지원되는 제품 및 하드웨어
소프트웨어 프로그래밍 도구

UNIFLASH — UniFlash for most TI microcontrollers (MCUs) and mmWave sensors

UniFlash는 TI의 광범위한 CCStudio™ 개발 에코시스템의 일부로, TI 마이크로컨트롤러 및 무선 연결 장치의 온칩 플래시와 TI 프로세서의 온보드 플래시를 프로그래밍하기 위한 소프트웨어 도구입니다. UniFlash는 그래픽 및 명령줄 인터페이스를 모두 제공하며, 데스크톱 또는 클라우드 환경에서 실행할 수 있습니다.

UniFlash는 CCStudio 개발자 영역의 클라우드에서 실행하거나 Windows®, Linux®, macOS® 컴퓨터에서 다운로드해 사용할 수 있습니다.

macOS는 mmWave, AMx, K2G 및 (...)

지원되는 제품 및 하드웨어
지원 소프트웨어

RADAR-TOOLBOX — Radar evaluation and development support package with example projects, documentation and tools

The Radar Toolbox is a collection of demos, software tools, and documentation designed to assist in the evaluation of TI Radar Devices
지원되는 제품 및 하드웨어
시뮬레이션 모델

IBIS model for IWRL6432W (Rev. A)

SWRM062A.ZIP (2275 KB) - IBIS 모델
지원되는 제품 및 하드웨어
시뮬레이션 모델

IWRL6432W BSDL model (Rev. A)

SPRM869A.ZIP (1 KB) - BSDL 모델
지원되는 제품 및 하드웨어
레퍼런스 디자인

TIDEP-01040 — 산업용 애플리케이션을 위한 웨이퍼 칩 스케일 패키지 60GHz mmWave 센서 레퍼런스 디자인

이 레퍼런스 설계는 폼 팩터가 더 작고 전력 소비가 낮아야 하는 애플리케이션을 대상으로 합니다. 이 설계는 TI의 IWRL6432W, 60GHz mmWave 레이더 장치를 기반으로 하며, Isola®의 FR408HR 재료와 함께 4레이어 PCB 스택업을 사용합니다. 또한 이 레퍼런스 설계는 디버그 및 평가 인터페이스가 없는 더 작은 폼 팩터 장치도 제공합니다.
지원되는 제품 및 하드웨어
패키지 CAD 기호, 풋프린트 및 3D 모델
DSBGA (YFF) 111 Ultra Librarian

주문 및 품질

권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.

지원 및 교육

TI 엔지니어의 기술 지원을 받을 수 있는 TI E2E™ 포럼

콘텐츠는 TI 및 커뮤니티 기고자에 의해 "있는 그대로" 제공되며 TI의 사양으로 간주되지 않습니다. 사용 약관을 참조하십시오.

품질, 패키징, TI에서 주문하는 데 대한 질문이 있다면 TI 지원을 방문하세요. ​​​​​​​​​​​​​​

동영상