SN74LVT16646

활성

3상 출력을 지원하는 3.3V ABT 16비트 버스 트랜시버 및 레지스터

지금 주문하기

데이터 시트

document-pdfAcrobat SN54LVT16646, SN74LVT16646 datasheet (Rev. D) (영어)

SN74LVT16646

활성

데이터 시트

지금 주문하기

제품 상세 정보

Number of channels

16

IOL (max) (mA)

64

IOH (max) (mA)

-32

Input type

TTL/CMOS

Output type

LVTTL

Features

Bus-hold, Over-voltage tolerant inputs, Partial power down (Ioff), Power up 3-state, Very high speed (tpd 5-10ns)

Technology family

LVT

Rating

Catalog

Operating temperature range (°C)

-40 to 85

Number of channels

16

IOL (max) (mA)

64

IOH (max) (mA)

-32

Input type

TTL/CMOS

Output type

LVTTL

Features

Bus-hold, Over-voltage tolerant inputs, Partial power down (Ioff), Power up 3-state, Very high speed (tpd 5-10ns)

Technology family

LVT

Rating

Catalog

Operating temperature range (°C)

-40 to 85

SSOP (DL)

56

190.647 mm² (18.42 mm × 10.35 mm)

Members of the Texas Instruments Widebus™ Family
State-of-the-Art Advanced BiCMOS Technology (ABT) Design for 3.3-V Operation and Low-Static Power Dissipation
Support Mixed-Mode Signal Operation (5-V Input and Output Voltages With 3.3-V V_CC)
Support Unregulated Battery Operation Down to 2.7 V
Typical V_OLP (Output Ground Bounce)
< 0.8 V at V_CC = 3.3 V, T_A = 25°C
Bus-Hold Data Inputs Eliminate the Need for External Pullup Resistors
I_off and Power-Up 3-State Support Hot Insertion
Distributed V_CC and GND Pin Configuration Minimizes High-Speed Switching Noise
Flowthrough Architecture Optimizes PCB Layout
Latch-Up Performance Exceeds 500 mA Per JEDEC Standard JESD-17
ESD Protection Exceeds JESD 22
- 2000-V Human-Body Model (A114-A)
- 200-V Machine Model (A115-A)

Widebus is a trademark of Texas Instruments.

Members of the Texas Instruments Widebus™ Family
State-of-the-Art Advanced BiCMOS Technology (ABT) Design for 3.3-V Operation and Low-Static Power Dissipation
Support Mixed-Mode Signal Operation (5-V Input and Output Voltages With 3.3-V V_CC)
Support Unregulated Battery Operation Down to 2.7 V
Typical V_OLP (Output Ground Bounce)
< 0.8 V at V_CC = 3.3 V, T_A = 25°C
Bus-Hold Data Inputs Eliminate the Need for External Pullup Resistors
I_off and Power-Up 3-State Support Hot Insertion
Distributed V_CC and GND Pin Configuration Minimizes High-Speed Switching Noise
Flowthrough Architecture Optimizes PCB Layout
Latch-Up Performance Exceeds 500 mA Per JEDEC Standard JESD-17
ESD Protection Exceeds JESD 22
- 2000-V Human-Body Model (A114-A)
- 200-V Machine Model (A115-A)

Widebus is a trademark of Texas Instruments.

The 'LVT16646 are 16-bit bus transceivers designed for low-voltage (3.3-V) V_CC operation, but with the capability to provide a TTL interface to a 5-V system environment.

These devices can be used as two 8-bit transceivers or one 16-bit transceiver. Data on the A or B bus is clocked into the registers on the low-to-high transition of the appropriate clock (CLKAB or CLKBA) input. Figure 1 illustrates the four fundamental bus-management functions that can be performed with the ´LVT16646.

Output-enable (OE\) and direction-control (DIR) inputs are provided to control the transceiver functions. In the transceiver mode, data present at the high-impedance port may be stored in either register or in both. The select-control (SAB and SBA) inputs can multiplex stored and real-time (transparent mode) data. The circuitry used for select control eliminates the typical decoding glitch that occurs in a multiplexer during the transition between stored and real-time data. The direction control (DIR) determines which bus receives data when OE\ is low. In the isolation mode (OE\ high), A data may be stored in one register and/or B data may be stored in the other register.

When an output function is disabled, the input function is still enabled and may be used to store and transmit data. Only one of the two buses, A or B, may be driven at a time.

Active bus-hold circuitry holds unused or undriven inputs at a valid logic state. Use of pullup or pulldown resistors with the bus-hold circuitry is not recommended.

These devices are fully specified for hot-insertion applications using I_off and power-up 3-state. The I_off circuitry disables the outputs, preventing damaging current backflow through the devices when they are powered down. The power-up 3-state circuitry places the outputs in the high-impedance state during power up and power down, which prevents driver conflict.

To ensure the high-impedance state during power up or power down, OE\ should be tied to V_CC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

The 'LVT16646 are 16-bit bus transceivers designed for low-voltage (3.3-V) V_CC operation, but with the capability to provide a TTL interface to a 5-V system environment.

These devices can be used as two 8-bit transceivers or one 16-bit transceiver. Data on the A or B bus is clocked into the registers on the low-to-high transition of the appropriate clock (CLKAB or CLKBA) input. Figure 1 illustrates the four fundamental bus-management functions that can be performed with the ´LVT16646.

Output-enable (OE\) and direction-control (DIR) inputs are provided to control the transceiver functions. In the transceiver mode, data present at the high-impedance port may be stored in either register or in both. The select-control (SAB and SBA) inputs can multiplex stored and real-time (transparent mode) data. The circuitry used for select control eliminates the typical decoding glitch that occurs in a multiplexer during the transition between stored and real-time data. The direction control (DIR) determines which bus receives data when OE\ is low. In the isolation mode (OE\ high), A data may be stored in one register and/or B data may be stored in the other register.

When an output function is disabled, the input function is still enabled and may be used to store and transmit data. Only one of the two buses, A or B, may be driven at a time.

Active bus-hold circuitry holds unused or undriven inputs at a valid logic state. Use of pullup or pulldown resistors with the bus-hold circuitry is not recommended.

These devices are fully specified for hot-insertion applications using I_off and power-up 3-state. The I_off circuitry disables the outputs, preventing damaging current backflow through the devices when they are powered down. The power-up 3-state circuitry places the outputs in the high-impedance state during power up and power down, which prevents driver conflict.

To ensure the high-impedance state during power up or power down, OE\ should be tied to V_CC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

filter

기타 범용 트랜시버 찾기

다운로드 스크립트와 함께 비디오 보기 비디오