設計工具
LM7332
- VS = ±15 V, TA = 25°C, Typical Values Unless
Specified - Wide Supply Voltage Range 2.5 V to 32 V
- Wide Input Common Mode Voltage 0.3 V Beyond
Rails - Output Short Circuit Current > 100 mA
- High Output Current (1 V from Rails) ±70 mA
- GBWP 21 MHz
- Slew Rate 15.2 V/µs
- Capacitive Load Tolerance Unlimited
- Total Supply Current 2 mA
- Temperature Range –40°C to +125°C
- Tested at –40°C, +125°C,
and +25°C at 5 V, ±5 V, ±15 V
The LM7332 device is a dual rail-to-rail input and output amplifier with a wide operating temperature range (–40°C to +125°C) that meets the needs of automotive, industrial, and power supply applications. The LM7332 has an output current of 100 mA, which is higher than that of most monolithic operational amplifiers. Circuit designs with high output current requirements often require discrete transistors because many operational amplifiers have low current output. The LM7332 has enough current output to drive many loads directly, saving the cost and space of the discrete transistors.
The exceptionally wide operating supply voltage range of 2.5 V to 32 V alleviates any concerns over functionality under extreme conditions and offers flexibility of use in a multitude of applications. Most parameters of this device are insensitive to power supply variations; this design enhancement is another step in simplifying usage. Greater than rail-to-rail input common mode voltage range allows operation in many applications, including high-side and low-side sensing, without exceeding the input range.
The LM7332 can drive unlimited capacitive loads without oscillations.
The LM7332 is offered in the 8-pin VSSOP and SOIC packages.
技術文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 4 | 類型 | 標題 | 日期 | ||
|---|---|---|---|---|
| * | Data sheet | LM7332 Dual Rail-to-Rail Input and Output 30-V, Wide Voltage Range, High Output, Operational Amplifier datasheet (Rev. B) | PDF | HTML | 2016年 1月 6日 |
| Application brief | Using An Op Amp for High-Side Current Sensing (Rev. A) | PDF | HTML | 2021年 12月 7日 | |
| Circuit design | Buffer (follower) circuit (Rev. A) | PDF | HTML | 2019年 1月 14日 | |
| E-book | The Signal e-book: A compendium of blog posts on op amp design topics | 2017年 3月 28日 |
設計與開發
如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。
開發板
DIP-ADAPTER-EVM — DIP 轉接器評估模組
Speed up your op amp prototyping and testing with the DIP-Adapter-EVM, which provides a fast, easy and inexpensive way to interface with small, surface-mount ICs. You can connect any supported op amp using the included Samtec terminal strips or wire them directly to existing circuits.
The (...)
使用指南: PDF
開發板
DUAL-DIYAMP-EVM — 雙通道通用自製 (DIY) 放大器電路評估模組
The DUAL-DIYAMP-EVM is a unique evaluation module (EVM) family that provides engineers and do it yourselfers (DIYers) with real-world amplifier circuits, enabling you to quickly evaluate design concepts and verify simulations. It is designed specifically for dual package op amps in the (...)
使用指南: PDF
計算工具
ANALOG-ENGINEER-CALC — 類比工程師計算機
The Analog Engineer’s Calculator is designed to speed up many of the repetitive calculations that analog circuit design engineers use on a regular basis. This PC-based tool provides a graphical interface with a list of various common calculations ranging from setting op-amp gain with feedback (...)
設計工具
CIRCUIT060013 — 具有 T 網路回饋電路的反相放大器
此設計可反轉輸入訊號 VIN，並使用 1000 V/V 或 60 dB 訊號增益。具有 T 回饋網路的反相放大器可在沒有較小 R4 值或超大回饋電阻器值的情況下獲得高增益。
設計工具
CIRCUIT060021 — 緩衝器 (隨耦器) 電路
This design is used to buffer signals by presenting a high input impedance and a low output impedance. This circuit is commonly used to drive low-impedance loads, analog-to-digital converters (ADC) and buffer reference voltages. The output voltage of this circuit is equal to the input voltage.
設計工具
CIRCUIT060074 — 具有比較器電路的高壓側電流感測
此高壓側電流感測解決方案使用一個具有軌對軌輸入共模範圍的比較器，若負載電流上升到 1 A 以上，便在比較器輸出 (COMP OUT) 建立過電流警示 (OC 警示) 訊號。此實作中的 OC 訊號為低電位作動。因此當超過 1-A 閾值時，比較器輸出會變低。實作磁滯後會在負載電流降低至 0.5 A (減少 50%) 時，讓 OC-Alert 返回邏輯高狀態。此電路利用開漏輸出比較器，為控制數位邏輯輸入針腳而進行電平轉換輸出高邏輯電平。對於需要驅動 MOSFET 開關閘極的應用，建議使用具推挽輸出的比較器。
模擬工具
PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具
PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
模擬工具
TINA-TI — 基於 SPICE 的類比模擬程式
TINA-TI provides all the conventional DC, transient and frequency domain analysis of SPICE and much more. TINA has extensive post-processing capability that allows you to format results the way you want them. Virtual instruments allow you to select input waveforms and probe circuit nodes voltages (...)
使用指南: PDF
| 封裝 | 引腳 | 下載 |
|---|---|---|
| SOIC (D) | 8 | 檢視選項 |
| VSSOP (DGK) | 8 | 檢視選項 |
訂購與品質
內含資訊：
- RoHS
- REACH
- 產品標記
- 鉛塗層/球物料
- MSL 等級/回焊峰值
- MTBF/FIT 估算值
- 材料內容
- 資格摘要
- 進行中可靠性監測
內含資訊：
- 晶圓廠位置
- 組裝地點