首頁 音訊、觸覺和壓電 音訊放大器 喇叭、電視與條型音箱音訊放大器
首頁
音訊、觸覺和壓電
音訊放大器
喇叭、電視與條型音箱音訊放大器

TAS5342LA

現行

100-W 立體聲道、200-W 單聲道、10.8-V 至 13.2-V 電源、PWM 輸入開迴路 D 類音訊放大器、低 RDSon

立即訂購
產品規格表

TAS5342LA

現行
立即訂購

產品詳細資料

Audio input type PWM Architecture Class-D Speaker channels (max) 4 Control interface Hardware Output power (W) 100 Power stage supply (max) (V) 13.2 Power stage supply (min) (V) 10.8 RDS(on) (Ω) 0.11 THD + N at 1 kHz (%) 0.09 Load (min) (Ω) 2 Analog supply voltage (min) (V) 10.8 Analog supply voltage (max) (V) 13.2 Rating Catalog Operating temperature range (°C) 0 to 70
Audio input type PWM Architecture Class-D Speaker channels (max) 4 Control interface Hardware Output power (W) 100 Power stage supply (max) (V) 13.2 Power stage supply (min) (V) 10.8 RDS(on) (Ω) 0.11 THD + N at 1 kHz (%) 0.09 Load (min) (Ω) 2 Analog supply voltage (min) (V) 10.8 Analog supply voltage (max) (V) 13.2 Rating Catalog Operating temperature range (°C) 0 to 70
HTSSOP (DDV) 44 113.4 mm² (14 mm × 8.1 mm)
  • Total Power Output (Bridge Tied Load)
    • 2 × 100 W at 10% THD+N Into 4 Ω
    • 2 × 80 W at 10% THD+N Into 6 Ω
    • 2 × 65 W at 10% THD+N Into 8 Ω
  • Total Power Output (Single Ended)
    • 4 × 40 W at 10% THD+N Into 3 Ω
    • 4 × 30 W at 10% THD+N Into 4 Ω
  • Total Power Output (Parallel Mode)
    • 1 × 200 W at 10% THD+N Into 2 Ω
    • 1 × 160 W at 10% THD+N Into 3 Ω
  • >110 dB SNR (A-Weighted With TAS5518 Modulator)
  • <0.1% THD+N (1 W, 1 kHz)
  • Supports PWM Frame Rates of 192 kHz to 432 kHz
  • Resistor-Programmable Current Limit
  • Integrated Self-Protection Circuitry, Including:
    • Under Voltage Protection
    • Overtemperature Warning and Error
    • Overload Protection
    • Short-Circuit Protection
    • PWM Activity Detector
  • Standalone Protection Recovery
  • Power-On Reset (POR) to Eliminate System Power-Supply Sequencing
  • High-Efficiency Power Stage (>90%) With 110-mΩ Output MOSFETs
  • Thermally Enhanced Package 44-Pin HTSSOP (DDV)
  • Error Reporting, 3.3-V and 5-V Compliant
  • EMI Compliant When Used With Recommended System Design
  • Total Power Output (Bridge Tied Load)
    • 2 × 100 W at 10% THD+N Into 4 Ω
    • 2 × 80 W at 10% THD+N Into 6 Ω
    • 2 × 65 W at 10% THD+N Into 8 Ω
  • Total Power Output (Single Ended)
    • 4 × 40 W at 10% THD+N Into 3 Ω
    • 4 × 30 W at 10% THD+N Into 4 Ω
  • Total Power Output (Parallel Mode)
    • 1 × 200 W at 10% THD+N Into 2 Ω
    • 1 × 160 W at 10% THD+N Into 3 Ω
  • >110 dB SNR (A-Weighted With TAS5518 Modulator)
  • <0.1% THD+N (1 W, 1 kHz)
  • Supports PWM Frame Rates of 192 kHz to 432 kHz
  • Resistor-Programmable Current Limit
  • Integrated Self-Protection Circuitry, Including:
    • Under Voltage Protection
    • Overtemperature Warning and Error
    • Overload Protection
    • Short-Circuit Protection
    • PWM Activity Detector
  • Standalone Protection Recovery
  • Power-On Reset (POR) to Eliminate System Power-Supply Sequencing
  • High-Efficiency Power Stage (>90%) With 110-mΩ Output MOSFETs
  • Thermally Enhanced Package 44-Pin HTSSOP (DDV)
  • Error Reporting, 3.3-V and 5-V Compliant
  • EMI Compliant When Used With Recommended System Design

The TAS5342LA is a high-performance, integrated stereo digital amplifier power stage designed to drive a 4-Ω bridge-tied load (BTL) at up to 100 W per channel with low-harmonic distortion, low-integrated noise, and low-idle current.

The TAS5342LA has a complete protection system integrated on-chip, safeguarding the device against a wide range of fault conditions that could damage the system. These protection features are short-circuit protection, over-current protection, under voltage protection, over temperature protection, and a loss of PWM signal (PWM activity detector).

A power-on-reset (POR) circuit is used to eliminate power-supply sequencing that is required for most power-stage designs.

The TAS5342LA is a high-performance, integrated stereo digital amplifier power stage designed to drive a 4-Ω bridge-tied load (BTL) at up to 100 W per channel with low-harmonic distortion, low-integrated noise, and low-idle current.

The TAS5342LA has a complete protection system integrated on-chip, safeguarding the device against a wide range of fault conditions that could damage the system. These protection features are short-circuit protection, over-current protection, under voltage protection, over temperature protection, and a loss of PWM signal (PWM activity detector).

A power-on-reset (POR) circuit is used to eliminate power-supply sequencing that is required for most power-stage designs.
filter 尋找其它 喇叭、電視與條型音箱音訊放大器
下載 觀看有字幕稿的影片 影片

您可能會感興趣的類似產品

open-in-new 比較替代產品
功能相似於所比較的產品。
TAS5612LA 現行 125W 立體聲、250W 單聲道、12 至 34V 電源供電、PWM 輸入 D 類音訊放大器 This product is a higher power (60-W) stereo analog-input Class-D amplifier
TPA3245 現行 115W 立體聲道、230W 單聲道、12 至 31.5V 電源、類比輸入 D 類音訊放大器 This product is an Ultra-Low 0.005% THD, higher power (115-W) analog-input class-D amplifier
TPA3244 現行 60-W 立體聲道、120-W 單聲道、12 至 31.5-V 電源、類比輸入 D 類音訊放大器、焊盤朝下 This product is an Ultra-Low 0.005% THD, higher power (115-W) analog-input class-D amplifier

技術文件

找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 5
重要文件 類型 標題 格式選項 下載最新的英文版本 日期
* 資料表 TAS5342LA 100-W Stereo Digital Amplifier Power Stage datasheet (Rev. A) PDF | HTML 2016/11/11
應用說明 LC Filter Design (Rev. B) PDF | HTML 2026/6/29
應用說明 Guidelines for Measuring Audio Power Amplifier Performance (Rev. A) 2019/8/26
應用說明 AN-1849 An Audio Amplifier Power Supply Design (Rev. C) 2019/6/27
應用說明 AN-1737 Managing EMI in Class D Audio Applications (Rev. A) 2013/5/1

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

封裝 針腳 CAD 符號、佔位空間與 3D 模型
HTSSOP (DDV) 44 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片