首頁 音訊、觸覺和壓電 音訊放大器 通用型音訊放大器
首頁
音訊、觸覺和壓電
音訊放大器
通用型音訊放大器

TPA2013D1

現行

具整合式升壓轉換器的 2.7-W、單聲道類比輸入 D 類音訊放大器

立即訂購
產品規格表

TPA2013D1

現行
產品規格表 立即訂購

產品詳細資料

Audio input type Analog Input Architecture Class-D Boosted Speaker channels (max) Mono Control interface GPIO Output power (W) 2.7 Power stage supply (max) (V) 5.5 Power stage supply (min) (V) 1.8 THD + N at 1 kHz (%) 1 Load (min) (Ω) 4 Analog supply voltage (min) (V) 2.3 Analog supply voltage (max) (V) 5.2 Rating Catalog Operating temperature range (°C) -40 to 85
Audio input type Analog Input Architecture Class-D Boosted Speaker channels (max) Mono Control interface GPIO Output power (W) 2.7 Power stage supply (max) (V) 5.5 Power stage supply (min) (V) 1.8 THD + N at 1 kHz (%) 1 Load (min) (Ω) 4 Analog supply voltage (min) (V) 2.3 Analog supply voltage (max) (V) 5.2 Rating Catalog Operating temperature range (°C) -40 to 85
VQFN (RGP) 20 16 mm² (4 mm × 4 mm) DSBGA (YZH) 16 5.0625 mm² (— mm × — mm)
  • High Efficiency Integrated Boost Converter (Over
    90% Efficiency)
  • 2.2-W into an 8-Ω Load from a 3.6-V Supply
  • 2.7-W into an 4-Ω Load from a 3.6-V Supply
  • Operates from 1.8 V to 5.5 V
  • Efficient Class-D Prolongs Battery Life
  • Independent Shutdown for Boost Converter and
    Class-D Amplifier
  • Differential Inputs Reduce RF Common Noise
  • Built-In INPUT Low-Pass Filter Decreases RF and
    Out-of-Band Noise Sensitivity
  • Synchronized Boost and Class-D Eliminates Beat
    Frequencies
  • Thermal and Short-Circuit Protection
  • Available in 2.275-mm × 2.275-mm 16-ball WCSP
    and 4-mm × 4-mm 20-Lead QFN Packages
  • 3 Selectable Gain Settings of 2 V/V, 6 V/V, and
    10 V/V
  • High Efficiency Integrated Boost Converter (Over
    90% Efficiency)
  • 2.2-W into an 8-Ω Load from a 3.6-V Supply
  • 2.7-W into an 4-Ω Load from a 3.6-V Supply
  • Operates from 1.8 V to 5.5 V
  • Efficient Class-D Prolongs Battery Life
  • Independent Shutdown for Boost Converter and
    Class-D Amplifier
  • Differential Inputs Reduce RF Common Noise
  • Built-In INPUT Low-Pass Filter Decreases RF and
    Out-of-Band Noise Sensitivity
  • Synchronized Boost and Class-D Eliminates Beat
    Frequencies
  • Thermal and Short-Circuit Protection
  • Available in 2.275-mm × 2.275-mm 16-ball WCSP
    and 4-mm × 4-mm 20-Lead QFN Packages
  • 3 Selectable Gain Settings of 2 V/V, 6 V/V, and
    10 V/V

The TPA2013D1 device is a high efficiency Class-D audio power amplifier with an integrated boost converter. It drives up to 2.7 W (10% THD+N) into a 4-Ω speaker. With 85% typical efficiency, the TPA2013D1 helps extend battery life when playing audio.

The built-in boost converter generates the voltage rail for the Class-D amplifier. This provides a louder audio output than a stand-alone amplifier connected directly to the battery. It also maintains a consistent loudness, regardless of battery voltage. Additionally, the boost converter can be used to supply external devices.

The TPA2013D1 has an integrated low pass filter to improve RF rejection and reduce out-of-band noise, increasing the signal-to-noise ratio (SNR). A built-in PLL synchronizes the boost converter and Class-D switching frequencies, thus eliminating beat frequencies and improving audio quality. All outputs are fully protected against shorts to ground, power supply, and output-to-output shorts.

The TPA2013D1 device is a high efficiency Class-D audio power amplifier with an integrated boost converter. It drives up to 2.7 W (10% THD+N) into a 4-Ω speaker. With 85% typical efficiency, the TPA2013D1 helps extend battery life when playing audio.

The built-in boost converter generates the voltage rail for the Class-D amplifier. This provides a louder audio output than a stand-alone amplifier connected directly to the battery. It also maintains a consistent loudness, regardless of battery voltage. Additionally, the boost converter can be used to supply external devices.

The TPA2013D1 has an integrated low pass filter to improve RF rejection and reduce out-of-band noise, increasing the signal-to-noise ratio (SNR). A built-in PLL synchronizes the boost converter and Class-D switching frequencies, thus eliminating beat frequencies and improving audio quality. All outputs are fully protected against shorts to ground, power supply, and output-to-output shorts.
filter 尋找其它 通用型音訊放大器
下載 觀看有字幕稿的影片 影片

技術文件

找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 8
重要文件 類型 標題 格式選項 下載最新的英文版本 日期
* 資料表 TPA2013D1 2.7-W Constant Output Power Class-D Audio Amplifier With Integrated Boost Converter datasheet (Rev. A) PDF | HTML 2016/3/31
應用說明 Guidelines for Measuring Audio Power Amplifier Performance (Rev. A) 2019/8/26
應用說明 AN-1849 An Audio Amplifier Power Supply Design (Rev. C) 2019/6/27
應用說明 AN-1737 Managing EMI in Class D Audio Applications (Rev. A) 2013/5/1
應用說明 Filter-Free Class-D Audio Amplifiers 2009/11/9
應用說明 TPA2013D1 Boost Converter Component Selection 2009/3/19
應用說明 TPA2013D1 Boost Converter Component Specification 2008/12/9
EVM User's guide TPA2013D1EVM - User Guide 2007/8/20

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

TPA2013D1EVM — TPA2013D1 評估模組 (EVM)

The TPA2013D1 is a 2.7 W Class-D amplifier with built-in boost converter. It drives up to 2.7 W (10% THD + N) into a 4 Ω speaker from low supply voltages.

The TPA2013D1 audio power amplifier evaluation module (TPA2013D1EVM) is a complete, stand alone audio board. It contains the TPA2013D1 QFN (...)

使用指南: PDF
支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
封裝 針腳 CAD 符號、佔位空間與 3D 模型
VQFN (RGP) 20 Ultra Librarian
DSBGA (YZH) 16 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片