驅動程式或資料庫
AFE032
- Supports:
- CENELEC Bands A, B, C, D
- ARIB STD-T84, FCC
- FSK, SFSK, and NB-OFDM
- Conforms To:
- EN50065-1, -2, -3, -7
- FCC, Part 15
- ARIB STD-T84
- Standards:
- G3, PRIME, P1901.2, ITU-G.hnem
- Programmable Tx Low-Pass Filters and
Rx Band-Pass Filters - Integrated Power-Line Driver with Thermal
and Overcurrent Protection - Low-Power Consumption:
- 50 mW (Receiver Mode)
- Receive Sensitivity: 10 µVRMS (Typ)
- Four-Wire SPI Interface
- Three Integrated Zero-Crossing Detectors
- Package: QFN-48 PowerPAD
- Extended Temperature Range:
–40°C to +125°C
The AFE032 is a low-cost, integrated, power-line communications (PLC), analog front-end (AFE) device capable of transformer-coupled connections to the power-line while under the control of a digital signal processor (DSP) or microcontroller. This device is ideal for driving high-current, low-impedance lines up to 1.9 A into reactive loads.
The integrated receiver is able to detect signals down to 10 µVRMS (G3-FCC mode) and is capable of a wide range of gain options to adapt to varying input-signal conditions. The monolithic integrated circuit provides high reliability in demanding power-line communication applications.
The AFE032 transmit power amplifier operates from a single supply in the range of 7 V to 24 V. At typical load current (IOUT = 1.5 APEAK), a wide output swing provides a 12-VPP capability with a nominal 15-V supply.
The device is internally protected against overtemperature and short-circuit conditions. The device also provides a selectable current limit. An interrupt output is provided, indicating current limit, thermal limit, and undervoltage. A shutdown pin is also available, and can be used to quickly place the device into the lowest-power state. Each functional block can be enabled or disabled to optimize power dissipation through the serial peripheral interface (SPI).
The AFE032 is housed in a thermally-enhanced, surface-mount, PowerPAD, QFN-48 package. Operation is specified over the extended industrial junction temperature range of –40°C to +125°C.
技術文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 3 | 類型 | 標題 | 日期 | ||
|---|---|---|---|---|
| * | Data sheet | Power-Line Communications Analog Front-End datasheet (Rev. A) | 2013年 12月 3日 | |
| E-book | Analog Engineer’s Pocket Reference Guide Fifth Edition (Rev. C) | 2018年 11月 30日 | ||
| E-book | The Signal e-book: A compendium of blog posts on op amp design topics | 2017年 3月 28日 |
設計與開發
如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。
計算工具
ANALOG-ENGINEER-CALC — 類比工程師計算機
The Analog Engineer’s Calculator is designed to speed up many of the repetitive calculations that analog circuit design engineers use on a regular basis. This PC-based tool provides a graphical interface with a list of various common calculations ranging from setting op-amp gain with feedback (...)
模擬工具
PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具
PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
模擬工具
TINA-TI — 基於 SPICE 的類比模擬程式
TINA-TI provides all the conventional DC, transient and frequency domain analysis of SPICE and much more. TINA has extensive post-processing capability that allows you to format results the way you want them. Virtual instruments allow you to select input waveforms and probe circuit nodes voltages (...)
使用指南: PDF
參考設計
TIDM-MINI-DC — 適用於較小型 AMI 網路、可降低基礎設施成本的資料集中器參考設計
The TIDM-MINI-DC reference design implements a light-weight powerline communication (PLC) data concentrator (DC) solution integrated with an Ethernet repeater feature. A power grid network is static, which means that once end-nodes are installed the number of nodes to be supported by a DC is (...)
| 封裝 | 引腳 | 下載 |
|---|---|---|
| VQFN (RGZ) | 48 | 檢視選項 |
訂購與品質
內含資訊：
- RoHS
- REACH
- 產品標記
- 鉛塗層/球物料
- MSL 等級/回焊峰值
- MTBF/FIT 估算值
- 材料內容
- 資格摘要
- 進行中可靠性監測
內含資訊：
- 晶圓廠位置
- 組裝地點