SBAS559B May   2022  – November 2025 ADS1285

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements: 1.65V ≤ IOVDD ≤ 1.95V and 2.7V ≤ IOVDD ≤ 3.6V
    7. 5.7 Switching Characteristics: 1.65V ≤ IOVDD ≤ 1.95V and 2.7V ≤ IOVDD ≤ 3.6V
    8. 5.8 Timing Diagrams
    9. 5.9 Typical Characteristics
  7. 6 Parameter Measurement Information
    1. 6.1 Noise Performance
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Analog Input
      2. 7.3.2 PGA and Buffer
        1. 7.3.2.1 Programmable Gain Amplifier (PGA)
        2. 7.3.2.2 Buffer Operation (PGA Bypass)
      3. 7.3.3 Voltage Reference Input
      4. 7.3.4 IOVDD Power Supply
      5. 7.3.5 Modulator
        1. 7.3.5.1 Modulator Overdrive
      6. 7.3.6 Digital Filter
        1. 7.3.6.1 Sinc Filter Section
        2. 7.3.6.2 FIR Filter Section
        3. 7.3.6.3 Group Delay and Step Response
          1. 7.3.6.3.1 Linear Phase Response
          2. 7.3.6.3.2 Minimum Phase Response
        4. 7.3.6.4 HPF Stage
      7. 7.3.7 Clock Input
      8. 7.3.8 GPIO
    4. 7.4 Device Functional Modes
      1. 7.4.1 Power Modes
      2. 7.4.2 Power-Down Mode
      3. 7.4.3 Reset
      4. 7.4.4 Synchronization
        1. 7.4.4.1 Pulse-Sync Mode
        2. 7.4.4.2 Continuous-Sync Mode
      5. 7.4.5 Sample Rate Converter
      6. 7.4.6 Offset and Gain Calibration
        1. 7.4.6.1 OFFSET Register
        2. 7.4.6.2 GAIN Register
        3. 7.4.6.3 Calibration Procedure
    5. 7.5 Programming
      1. 7.5.1 Serial Interface
        1. 7.5.1.1 Chip Select (CS)
        2. 7.5.1.2 Serial Clock (SCLK)
        3. 7.5.1.3 Data Input (DIN)
        4. 7.5.1.4 Data Output (DOUT)
        5. 7.5.1.5 Data Ready (DRDY)
      2. 7.5.2 Conversion Data Format
      3. 7.5.3 Commands
        1. 7.5.3.1  Single Byte Command
        2. 7.5.3.2  WAKEUP: Wake Command
        3. 7.5.3.3  STANDBY: Software Power-Down Command
        4. 7.5.3.4  SYNC: Synchronize Command
        5. 7.5.3.5  RESET: Reset Command
        6. 7.5.3.6  Read Data Direct
        7. 7.5.3.7  RDATA: Read Conversion Data Command
        8. 7.5.3.8  RREG: Read Register Command
        9. 7.5.3.9  WREG: Write Register Command
        10. 7.5.3.10 OFSCAL: Offset Calibration Command
        11. 7.5.3.11 GANCAL: Gain Calibration Command
    6. 7.6 Register Map
      1. 7.6.1 Register Descriptions
        1. 7.6.1.1 ID/SYNC: Device ID, SYNC Register (Address = 00h) [Reset = xxxx0000b]
        2. 7.6.1.2 CONFIG0: Configuration Register 0 (Address = 01h) [Reset = 12h]
        3. 7.6.1.3 CONFIG1: Configuration Register 1 (Address = 02h) [Reset = 00h]
        4. 7.6.1.4 HPF0, HPF1: High-Pass Filter Registers (Address = 03h, 04h) [Reset = 32h, 03h]
        5. 7.6.1.5 OFFSET0, OFFSET1, OFFSET2: Offset Calibration Registers (Address = 05h, 06h, 07h) [Reset = 00h, 00h, 00h]
        6. 7.6.1.6 GAIN0, GAIN1, GAIN2: Gain Calibration Registers (Address = 08h, 09h, 0Ah) [Reset = 00h, 00h, 40h]
        7. 7.6.1.7 GPIO: Digital Input/Output Register (Address = 0Bh) [Reset = 000xx000b]
        8. 7.6.1.8 SRC0, SRC1: Sample Rate Converter Registers (Address = 0Ch, 0Dh) [Reset = 00h, 80h]
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
      3. 8.2.3 Application Curves
    3. 8.3 Power Supply Recommendations
      1. 8.3.1 Analog Power Supplies
      2. 8.3.2 Digital Power Supply
      3. 8.3.3 Grounds
      4. 8.3.4 Thermal Pad
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Receiving Notification of Documentation Updates
    2. 9.2 Support Resources
    3. 9.3 Trademarks
    4. 9.4 Electrostatic Discharge Caution
    5. 9.5 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

5.3 Recommended Operating Conditions

over operating ambient temperature range (unless otherwise noted)
MIN NOM MAX UNIT
POWER SUPPLY
Analog power supplies AVDD1 to AVSS 3 5.25 V
AVDD1 to AGND 2.375 V
AVSS to AGND –2.625 0
AVDD2 to AGND 2.375 5.25
AVDD2 to AVSS 5.25
Digital power supply IOVDD to DGND 2.7 3.6 V
IOVDD connected to CAPD 1.65 1.95
ANALOG INPUTS
VIN Differential input voltage
VIN = VAINP – VAINN		 Reference voltage = 5V ±VREF / (2 × Gain) V
Reference voltage = 4.096V ±VREF / (1.6384 × Gain)
Reference voltage = 2.5V ±VREF / Gain
Absolute input voltage Buffer operation AVSS + 0.1 AVDD1 – 0.1 V
PGA operation AVSS + 1.1 AVDD1 – 0.85
Absolute output voltage Buffer operation AVSS + 0.1 AVDD1 – 0.1 V
PGA operation AVSS + 0.15 AVDD1 – 0.15
Calibration range (1) 6% FSR
VOLTAGE REFERENCE INPUT
VREFN Negative reference input AVSS – 0.05 V
VREFP Positive reference input AVDD1 + 0.1 V
VREF VREF = VREFP – VREFN Reference voltage = 5V 4.9 5 AVDD1 – AVSS + 0.1 V
Reference voltage = 4.096V 4.0 4.096 4.2 V
Reference voltage = 2.5V 2.4 2.5 2.6 V
DIGITAL INPUTS
VINL Low-level input voltage 0.2 × IOVDD V
VINH High-level input voltage 0.8 × IOVDD V
fCLK Clock input frequency High-power mode 6 8.192 8.3 MHz
Mid-power mode 6 8.192 8.3
Low-power mode 3 4.096 4.15
TEMPERATURE
TA Ambient temperature Operational –50 85 °C
Specification –40 85
(1) Calibration range is the sum of the offset and gain error correction.