SWRS226B February   2020  – May 2021 CC3230S , CC3230SF

PRODUCTION DATA  

  1. Features
  2. Applications
  3. Description
  4. Functional Block Diagrams
  5. Revision History
  6. Device Comparison
    1. 6.1 Related Products
  7. Terminal Configuration and Functions
    1. 7.1 Pin Diagram
    2. 7.2 Pin Attributes
      1. 7.2.1 Pin Descriptions
    3. 7.3 Signal Descriptions
      1.      13
    4. 7.4 Pin Multiplexing
    5. 7.5 Drive Strength and Reset States for Analog and Digital Multiplexed Pins
    6. 7.6 Pad State After Application of Power to Device, Before Reset Release
    7. 7.7 Connections for Unused Pins
  8. Specifications
    1. 8.1  Absolute Maximum Ratings
    2. 8.2  ESD Ratings
    3. 8.3  Power-On Hours (POH)
    4. 8.4  Recommended Operating Conditions
    5. 8.5  Current Consumption Summary (CC3230S)
      1.      24
    6. 8.6  Current Consumption Summary (CC3230SF)
      1.      26
    7. 8.7  TX Power Control
    8. 8.8  Brownout and Blackout Conditions
    9. 8.9  Electrical Characteristics for GPIO Pins
      1. 8.9.1 Electrical Characteristics: GPIO Pins Except 29, 30, 50, 52, and 53
      2. 8.9.2 Electrical Characteristics: GPIO Pins 29, 30, 50, 52, and 53
    10. 8.10 Electrical Characteristics for Pin Internal Pullup and Pulldown
      1.      33
    11. 8.11 WLAN Receiver Characteristics
      1.      35
    12. 8.12 WLAN Transmitter Characteristics
      1.      37
    13. 8.13 WLAN Transmitter Out-of-Band Emissions
      1. 8.13.1 WLAN Filter Requirements
    14. 8.14 BLE/2.4 GHz Radio Coexistence and WLAN Coexistence Requirements
    15. 8.15 Thermal Resistance Characteristics for RGK Package
    16. 8.16 Timing and Switching Characteristics
      1. 8.16.1 Power Supply Sequencing
      2. 8.16.2 Device Reset
      3. 8.16.3 Reset Timing
        1. 8.16.3.1 nRESET (32-kHz Crystal)
        2. 8.16.3.2 First-Time Power-Up and Reset Removal Timing Requirements (32-kHz Crystal)
        3. 8.16.3.3 nRESET (External 32-kHz Clock)
          1. 8.16.3.3.1 First-Time Power-Up and Reset Removal Timing Requirements (External 32-kHz Clock)
      4. 8.16.4 Wakeup From HIBERNATE Mode
      5. 8.16.5 Clock Specifications
        1. 8.16.5.1 Slow Clock Using Internal Oscillator
        2. 8.16.5.2 Slow Clock Using an External Clock
          1. 8.16.5.2.1 External RTC Digital Clock Requirements
        3. 8.16.5.3 Fast Clock (Fref) Using an External Crystal
          1. 8.16.5.3.1 WLAN Fast-Clock Crystal Requirements
        4. 8.16.5.4 Fast Clock (Fref) Using an External Oscillator
          1. 8.16.5.4.1 External Fref Clock Requirements (–40°C to +85°C)
      6. 8.16.6 Peripherals Timing
        1. 8.16.6.1  SPI
          1. 8.16.6.1.1 SPI Master
            1. 8.16.6.1.1.1 SPI Master Timing Parameters
          2. 8.16.6.1.2 SPI Slave
            1. 8.16.6.1.2.1 SPI Slave Timing Parameters
        2. 8.16.6.2  I2S
          1. 8.16.6.2.1 I2S Transmit Mode
            1. 8.16.6.2.1.1 I2S Transmit Mode Timing Parameters
          2. 8.16.6.2.2 I2S Receive Mode
            1. 8.16.6.2.2.1 I2S Receive Mode Timing Parameters
        3. 8.16.6.3  GPIOs
          1. 8.16.6.3.1 GPIO Output Transition Time Parameters (Vsupply = 3.3 V)
            1. 8.16.6.3.1.1 GPIO Output Transition Times (Vsupply = 3.3 V) (1) (1)
          2. 8.16.6.3.2 GPIO Input Transition Time Parameters
            1. 8.16.6.3.2.1 GPIO Input Transition Time Parameters
        4. 8.16.6.4  I2C
          1. 8.16.6.4.1 I2C Timing Parameters (1)
        5. 8.16.6.5  IEEE 1149.1 JTAG
          1. 8.16.6.5.1 JTAG Timing Parameters
        6. 8.16.6.6  ADC
          1. 8.16.6.6.1 ADC Electrical Specifications
        7. 8.16.6.7  Camera Parallel Port
          1. 8.16.6.7.1 Camera Parallel Port Timing Parameters
        8. 8.16.6.8  UART
        9. 8.16.6.9  SD Host
        10. 8.16.6.10 Timers
  9. Detailed Description
    1. 9.1  Overview
    2. 9.2  Arm® Cortex®-M4 Processor Core Subsystem
    3. 9.3  Wi-Fi® Network Processor Subsystem
      1. 9.3.1 WLAN
      2. 9.3.2 Network Stack
    4. 9.4  Security
    5. 9.5  Power-Management Subsystem
    6. 9.6  Low-Power Operating Mode
    7. 9.7  Memory
      1. 9.7.1 External Memory Requirements
      2. 9.7.2 Internal Memory
        1. 9.7.2.1 SRAM
        2. 9.7.2.2 ROM
        3. 9.7.2.3 Flash Memory
        4. 9.7.2.4 Memory Map
    8. 9.8  Restoring Factory Default Configuration
    9. 9.9  Boot Modes
      1. 9.9.1 Boot Mode List
    10. 9.10 Hostless Mode
  10. 10Applications, Implementation, and Layout
    1. 10.1 Application Information
      1. 10.1.1 BLE/2.4 GHz Radio Coexistence
      2. 10.1.2 Antenna Selection
      3. 10.1.3 Typical Application
    2. 10.2 PCB Layout Guidelines
      1. 10.2.1 General PCB Guidelines
      2. 10.2.2 Power Layout and Routing
        1. 10.2.2.1 Design Considerations
      3. 10.2.3 Clock Interface Guidelines
      4. 10.2.4 Digital Input and Output Guidelines
      5. 10.2.5 RF Interface Guidelines
  11. 11Device and Documentation Support
    1. 11.1 Third-Party Products Disclaimer
    2. 11.2 Tools and Software
    3. 11.3 Firmware Updates
    4. 11.4 Device Nomenclature
    5. 11.5 Documentation Support
    6. 11.6 Support Resources
    7. 11.7 Trademarks
    8. 11.8 Electrostatic Discharge Caution
    9. 11.9 Glossary
  12. 12Mechanical, Packaging, and Orderable Information
    1. 12.1 Package Option Addendum
      1. 12.1.1 Packaging Information
      2. 12.1.2 Tape and Reel Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

Network Stack

The Network Stack features are as follows:

  • Integrated IPv4, IPv6 TCP/IP stack with BSD socket APIs for simple Internet connectivity with any MCU, microprocessor, or ASIC
    Note:

    Not all APIs are 100% BSD compliant. Not all BSD APIs are supported.

  • Support of 16 simultaneous TCP, UDP, RAW, SSL\TLS sockets
  • Built-in network protocols:
    • Static IP, LLA, DHCPv4, DHCPv6 with DAD and stateless autoconfiguration
    • ARP, ICMPv4, IGMP, ICMPv6, MLD, ND
    • DNS client for easy connection to the local network and the Internet
  • Built-in network applications and utilities:
    • HTTP/HTTPS
      • Web page content stored on serial flash
      • RESTful APIs for setting and configuring application content
      • Dynamic user callbacks
    • Service discovery: Multicast DNS service discovery lets a client advertise its service without a centralized server. After connecting to the access point, the CC3230x device provides critical information, such as device name, IP, vendor, and port number.
    • DHCP server
    • Ping

Table 9-1 describes the NWP features.

Table 9-1 NWP Features
FEATURE DESCRIPTION
Wi-Fi standards 802.11b/g/n station
802.11b/g AP supporting up to four stations
Wi-Fi Direct client and group owner
Wi-Fi channels 2.4 GHz ISM
Channel Bandwidth 20 MHz
Wi-Fi security WEP, WPA/WPA2 PSK, WPA2 enterprise (802.1x), WPA3 personal and enterprise (1)
Wi-Fi provisioning SmartConfig technology, Wi-Fi protected setup (WPS2), AP mode with internal HTTP web server
IP protocols IPv4/IPv6
IP addressing Static IP, LLA, DHCPv4, DHCPv6 with DAD
Cross layer ARP, ICMPv4, IGMP, ICMPv6, MLD, NDP
Transport UDP, TCP
SSLv3.0/TLSv1.0/TLSv1.1/TLSv1.2
RAW
Network applications and utilities Ping
HTTP/HTTPS web server
mDNS
DNS-SD
DHCP server
Host interface UART/SPI
Security Device identity
Trusted root-certificate catalog
TI root-of-trust public key
The CC3230S and CC3230SF variants also support:
  • Secure key storage
  • Online certificate status protocol (OCSP)
  • Certificate signing request (CSR)
  • Unique per device Key-Pair
  • File system security
  • Software tamper detection
  • Cloning protection
  • Secure boot
  • Validate the integrity and authenticity of the run-time binary during boot
  • Initial secure programming
  • Debug security
  • JTAG and debug
Power management Enhanced power policy management uses 802.11 power save and deep-sleep power modes
Other Transceiver
Programmable RX filters with event-trigger mechanism
Rx Metrics for tracking the surrounding RF environment
See CC3230 SDK v3.40 or newer for details. Limited to STA mode only.