SLVSI31 April   2026 TPS61371

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 I2C Timing Requirements
    7. 5.7 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1  Undervoltage Lockout
      2. 6.3.2  Enable and Disable
      3. 6.3.3  Output Voltage Setting
      4. 6.3.4  Reference Voltage Slew Rate
      5. 6.3.5  Error Amplifier
      6. 6.3.6  Bootstrap Voltage (BST)
      7. 6.3.7  Load Disconnect
      8. 6.3.8  Output Discharge
      9. 6.3.9  Overvoltage Protection
      10. 6.3.10 Thermal Shutdown
      11. 6.3.11 Start-Up
      12. 6.3.12 Short Protection
    4. 6.4 Device Functional Modes
      1. 6.4.1 Operation
      2. 6.4.2 Auto PFM Mode
      3. 6.4.3 Forced PWM Mode
      4. 6.4.4 Mode Selectable
    5. 6.5 Programming
      1. 6.5.1 Serial Interface Description
      2. 6.5.2 Standard-, Fast-, and Fast-Mode Plus Protocol
      3. 6.5.3 I2C Update Sequence
      4. 6.5.4 I2C Target Address
        1. 6.5.4.1 I2C Target Address Description
  8. 7 Register Map
    1. 7.1 Register Description
      1. 7.1.1 Register Map
      2. 7.1.2 Register CONTROL (Register address: 0x01; Default: 0x01)
      3. 7.1.3 Register VOUT (Register address: 0x02; Default: 0x36)
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Setting the Output Voltage
        2. 8.2.2.2 Selecting the Inductor
        3. 8.2.2.3 Selecting the Output Capacitors
        4. 8.2.2.4 Selecting the Input Capacitors
        5. 8.2.2.5 Loop Stability and Compensation
          1. 8.2.2.5.1 Small Signal Model
        6. 8.2.2.6 Loop Compensation Design Steps
        7. 8.2.2.7 Selecting the Bootstrap Capacitor
      3. 8.2.3 Application Curves
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
        1. 8.4.2.1 Thermal Considerations
  10. 9 Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Third-Party Products Disclaimer
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

Pin Configuration and Functions

TPS61371 VAR Package, 14-Pin WQFN-HR (Top View)Figure 4-1 VAR Package, 14-Pin WQFN-HR (Top View)
Table 4-1 Pin Functions
PINTYPE(1)DESCRIPTION
NUMBERNAME
1, 2VOUTPWRBoost converter output
3, 14SWPWRThe switching node pin of the converter. This pin is connected to the drain of the internal low-side FET and the source of the internal high-side FET. The pin-3 and pin-14 SW must be connected together. And put the inductor close to the pin-3 SW
4VINIIC power supply input
5BSTOPower supply for the high-side FET gate driver. A capacitor must be connected between this pin and the SW pin.
6ENIEnable logic input. Logic low level disables the device output. Logic high level and CONVERTER_EN = 1 enable the device output.
7MODEIOperation mode selection pin.
MODE = high, the device is in forced PWM mode and keeps the switching frequency constant across the whole load range, regardless of what the FPWM bit is set to MODE = low, the device work mode depends on the FPWM bit (bit = 0: auto PFM mode; bit = 1: FPWM mode).
8ADDRII2C target address set pin. See also Table 7-3.
9SDAI/OI2C serial interface data. Pull this pin up to the I2C bus voltage with a resistor.
10SCLII2C serial interface clock. Pull this pin up to the I2C bus voltage with a resistor.
11COMPOOutput of the internal error amplifier. The loop compensation network must be connected between this pin and GND.
12FBIOutput voltage feedback. A resistor divider connecting to this pin sets the default output voltage.
13GND—Ground
PWR = power, I = input, O = output