JAJSIN7 February   2020 TPS59632-Q1

PRODUCTION DATA.  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
    1.     Device Images
      1.      アプリケーション概略図
  4. 4 改訂履歴
  5. 5 Pin Configuration and Functions
    1.     Pin Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Switching Characteristics
    8. 6.8 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  PWM Operation
      2. 7.3.2  Current Sensing
      3. 7.3.3  Load-line (Droop)
      4. 7.3.4  Load Transients
      5. 7.3.5  Overshoot Reduction (OSR)
      6. 7.3.6  Undershoot Reduction (USR)
      7. 7.3.7  Autobalance Current Sharing
      8. 7.3.8  PWM And SKIP Signals
      9. 7.3.9  Bias Power (V5A, VDD, And VINTF) UVLO
      10. 7.3.10 Start-Up Sequence
      11. 7.3.11 Power Good Operation
      12. 7.3.12 Analog Current Monitor, IMON, And Corresponding Digital Output Current
      13. 7.3.13 Fault Behavior
      14. 7.3.14 Output Under Voltage Protection (UVP)
      15. 7.3.15 Output Over Voltage Protection (OVP)
      16. 7.3.16 Over Current Protection (OCP)
      17. 7.3.17 Over Current Warning
      18. 7.3.18 Input Voltage Limits
      19. 7.3.19 VID Table
    4. 7.4 User Selections
    5. 7.5 I2C Interface Operation
      1. 7.5.1 Key For Protocol Examples
      2. 7.5.2 Protocol Examples
    6. 7.6 I2C Register Maps
      1. 7.6.1 Voltage Select Register (VSR) (Address = 00h)
      2. 7.6.2 IMON Register (Address = 03h)
      3. 7.6.3 VMAX Register (Address = 04h)
      4. 7.6.4 Power State Register (Address = 06h)
      5. 7.6.5 Slew Register (Address = 07h)
      6. 7.6.6 Lot Code Registers (Address = 10-13h)
      7. 7.6.7 Fault Register (Address = 14h)
  8. 8 Applications and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 3-Phase D-CAP+™, Step-Down Application
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
          1. 8.2.1.2.1  Step 1: Select Switching Frequency
          2. 8.2.1.2.2  Step 2: Set The Slew Rate
          3. 8.2.1.2.3  Step 3: Set The I2C Address
          4. 8.2.1.2.4  Step 4: Determine Inductor Value And Choose Inductor
          5. 8.2.1.2.5  Step 5: Current Sensing Resistance
          6. 8.2.1.2.6  Step 6: Select Over Current Protection (OCP) Setting
          7. 8.2.1.2.7  Step 7: Current Monitor (IMON) Setting
          8. 8.2.1.2.8  Step 8: Set the Load-Line Slope
          9. 8.2.1.2.9  Step 9: Voltage Feedback Resistor Calculation
          10. 8.2.1.2.10 Step 10: Ramp Compensation Selection
          11. 8.2.1.2.11 Step 11 Overshoot Reduction (OSR) selection
          12. 8.2.1.2.12 Step 12: Undershoot Reduction (USR) selection
          13. 8.2.1.2.13 Step 13: Loop Compensation
        3. 8.2.1.3 Application Performance Plots
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1  Layout Guidelines
    2. 10.2  Layout Example
    3. 10.3  Current Sensing Lines
    4. 10.4  Feedback Voltage Sensing Lines
    5. 10.5  PWM And SKIP Lines
    6. 10.6  Power Chain Symmetry
    7. 10.7  Component Location
    8. 10.8  Grounding Recommendations
    9. 10.9  Decoupling Recommendations
    10. 10.10 Conductor Widths
  11. 11デバイスおよびドキュメントのサポート
    1. 11.1 ドキュメントのサポート
    2. 11.2 商標
    3. 11.3 静電気放電に関する注意事項
    4. 11.4 Glossary
  12. 12メカニカル、パッケージ、および注文情報
    1. 12.1 Package Option Addendum
      1. 12.1.1 Packaging Information
      2. 12.1.2 Tape And Reel Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

7.3.6 Undershoot Reduction (USR)

When the transient load increase becomes quite large, it is difficult to meet the energy demanded by the load especially at lower input voltages. Then it is necessary to quickly increase the energy in the inductors during the transient load increase. This increase is achieved by enabling pulse overlapping. In order to maintain the interleaving of the multi-phase configuration while maintaining pulse-overlapping during load-insertion, the undershoot reduction (USR) mode is entered only when necessary. This device enters this mode is when the difference between DROOP voltage and ISUM voltage exceeds the USR voltage level specified in the Electrical Characteristics table.

Figure 14 shows the undershoot reduction operation. This feature allows for the use of reduced output capacitance while continuing to meet the specification. The device achieves undershoot reduction by overlapping of pulses on all the phases.

TPS59632-Q1 v12238_lusas6.gifFigure 14. Undershoot Reduction

When the transient condition is completed, the interleaving of the phases is resumed.

It should be noted that single-phase mode there is no USR mode of operation.