SLASF33A January   2024  – March 2025 TAC5412-Q1

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  Electrical Characteristics
    6. 5.6  Timing Requirements: I2C Interface
    7. 5.7  Switching Characteristics: I2C Interface
    8. 5.8  Timing Requirements: SPI
    9. 5.9  Switching Characteristics: SPI
    10. 5.10 Timing Requirements: TDM, I2S or LJ Interface
    11. 5.11 Switching Characteristics: TDM, I2S or LJ Interface
    12. 5.12 Timing Requirements: PDM Digital Microphone Interface
    13. 5.13 Switching Characteristics: PDM Digial Microphone Interface
    14. 5.14 Timing Diagrams
    15. 5.15 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1  Serial Interfaces
        1. 6.3.1.1 Control Serial Interfaces
        2. 6.3.1.2 Audio Serial Interfaces
          1. 6.3.1.2.1 Time Division Multiplexed Audio (TDM) Interface
          2. 6.3.1.2.2 Inter IC Sound (I2S) Interface
          3. 6.3.1.2.3 Left-Justified (LJ) Interface
        3. 6.3.1.3 Using Multiple Devices With Shared Buses
      2. 6.3.2  Phase-Locked Loop (PLL) and Clock Generation
      3. 6.3.3  Input Channel Configuration
      4. 6.3.4  Reference Voltage
      5. 6.3.5  Microphone Bias
      6. 6.3.6  Digital PDM Microphone Record Channel
      7. 6.3.7  Signal-Chain Processing
        1. 6.3.7.1 ADC Signal-Chain
          1. 6.3.7.1.1  6 to 4 Input Select Multiplexer (6:4 MUX)
          2. 6.3.7.1.2  Programmable Channel Gain and Digital Volume Control
          3. 6.3.7.1.3  Programmable Channel Gain Calibration
          4. 6.3.7.1.4  Programmable Channel Phase Calibration
          5. 6.3.7.1.5  Programmable Digital High-Pass Filter
          6. 6.3.7.1.6  Programmable Digital Biquad Filters
          7. 6.3.7.1.7  Programmable Channel Summer and Digital Mixer
          8. 6.3.7.1.8  Configurable Digital Decimation Filters
            1. 6.3.7.1.8.1 Linear-phase filters
              1. 6.3.7.1.8.1.1 Sampling Rate: 8kHz or 7.35kHz
              2. 6.3.7.1.8.1.2 Sampling Rate: 16kHz or 14.7kHz
              3. 6.3.7.1.8.1.3 Sampling Rate: 24kHz or 22.05kHz
              4. 6.3.7.1.8.1.4 Sampling Rate: 32kHz or 29.4kHz
              5. 6.3.7.1.8.1.5 Sampling Rate: 48kHz or 44.1kHz
              6. 6.3.7.1.8.1.6 Sampling Rate: 96kHz or 88.2kHz
              7. 6.3.7.1.8.1.7 Sampling Rate: 192kHz or 176.4kHz
              8. 6.3.7.1.8.1.8 Sampling Rate: 384kHz or 352.8kHz
              9. 6.3.7.1.8.1.9 Sampling Rate: 768kHz or 705.6kHz
            2. 6.3.7.1.8.2 Low-latency Filters
              1. 6.3.7.1.8.2.1 Sampling Rate: 24kHz or 22.05kHz
              2. 6.3.7.1.8.2.2 Sampling Rate: 32kHz or 29.4kHz
              3. 6.3.7.1.8.2.3 Sampling Rate: 48kHz or 44.1kHz
              4. 6.3.7.1.8.2.4 Sampling Rate: 96kHz or 88.2kHz
              5. 6.3.7.1.8.2.5 Sampling Rate: 192kHz or 176.4kHz
            3. 6.3.7.1.8.3 Ultra-Low-Latency Filters
              1. 6.3.7.1.8.3.1 Sampling Rate: 24kHz or 22.05kHz
              2. 6.3.7.1.8.3.2 Sampling Rate: 32kHz or 29.4kHz
              3. 6.3.7.1.8.3.3 Sampling Rate: 48kHz or 44.1kHz
              4. 6.3.7.1.8.3.4 Sampling Rate: 96kHz or 88.2kHz
              5. 6.3.7.1.8.3.5 Sampling Rate: 192kHz or 176.4kHz
          9. 6.3.7.1.9  Automatic Gain Controller (AGC)
          10. 6.3.7.1.10 Voice Activity Detection (VAD)
          11. 6.3.7.1.11 Ultrasonic Activity Detection (UAD)
        2. 6.3.7.2 DAC Signal-Chain
          1. 6.3.7.2.1 Programmable Channel Gain and Digital Volume Control
          2. 6.3.7.2.2 Programmable Channel Gain Calibration
          3. 6.3.7.2.3 Programmable Digital High-Pass Filter
          4. 6.3.7.2.4 Programmable Digital Biquad Filters
          5. 6.3.7.2.5 Configurable Digital Interpolation Filters
            1. 6.3.7.2.5.1 Linear-phase filters
              1. 6.3.7.2.5.1.1 Sampling Rate: 8kHz or 7.35kHz
              2. 6.3.7.2.5.1.2 Sampling Rate: 16kHz or 14.7kHz
              3. 6.3.7.2.5.1.3 Sampling Rate: 24kHz or 22.05kHz
              4. 6.3.7.2.5.1.4 Sampling Rate: 32kHz or 29.4kHz
              5. 6.3.7.2.5.1.5 Sampling Rate: 48kHz or 44.1kHz
              6. 6.3.7.2.5.1.6 Sampling Rate: 96kHz or 88.2kHz
              7. 6.3.7.2.5.1.7 Sampling Rate: 192kHz or 176.4kHz
              8. 6.3.7.2.5.1.8 Sampling Rate: 384kHz or 352.8kHz
              9. 6.3.7.2.5.1.9 Sampling Rate 768kHz or 705.6kHz
            2. 6.3.7.2.5.2 Low-latency Filters
              1. 6.3.7.2.5.2.1 Sampling Rate: 24kHz or 22.05kHz
              2. 6.3.7.2.5.2.2 Sampling Rate: 32kHz or 29.4kHz
              3. 6.3.7.2.5.2.3 Sampling Rate: 48kHz or 44.1kHz
              4. 6.3.7.2.5.2.4 Sampling Rate: 96kHz or 88.2kHz
              5. 6.3.7.2.5.2.5 Sampling Rate: 192kHz or 176.4kHz
            3. 6.3.7.2.5.3 Ultra-Low-Latency Filters
              1. 6.3.7.2.5.3.1 Sampling Rate: 24kHz or 22.05kHz
              2. 6.3.7.2.5.3.2 Sampling Rate: 32kHz or 29.4kHz
              3. 6.3.7.2.5.3.3 Sampling Rate: 48kHz or 44.1kHz
              4. 6.3.7.2.5.3.4 Sampling Rate: 96kHz or 88.2kHz
              5. 6.3.7.2.5.3.5 Sampling Rate 192kHz or 176.4kHz
          6. 6.3.7.2.6 Programmable Digital Mixer
      8. 6.3.8  Interrupts, Status, and Digital I/O Pin Multiplexing
      9. 6.3.9  Input DC Fault Diagnostics
      10. 6.3.10 Power Tune Mode
    4. 6.4 Device Functional Modes
      1. 6.4.1 Sleep Mode or Software Shutdown
      2. 6.4.2 Active Mode
      3. 6.4.3 Software Reset
    5. 6.5 Programming
      1. 6.5.1 Control Serial Interfaces
        1. 6.5.1.1 I2C Control Interface
          1. 6.5.1.1.1 General I2C Operation
          2. 6.5.1.1.2 I2C Single-Byte and Multiple-Byte Transfers
            1. 6.5.1.1.2.1 I2C Single-Byte Write
            2. 6.5.1.1.2.2 I2C Multiple-Byte Write
            3. 6.5.1.1.2.3 I2C Single-Byte Read
            4. 6.5.1.1.2.4 I2C Multiple-Byte Read
        2. 6.5.1.2 SPI Control Interface
  8. 7 Register Maps
    1. 7.1 Device Configuration Registers
      1. 7.1.1 TAC5412-Q1_B0_P0 Registers
      2. 7.1.2 TAC5412-Q1_B0_P1 Registers
      3. 7.1.3 TAC5412-Q1_B0_P3 Registers
    2. 7.2 Programmable Coefficient Registers
      1. 7.2.1  Programmable Coefficient Registers: Page 8
      2. 7.2.2  Programmable Coefficient Registers: Page 9
      3. 7.2.3  Programmable Coefficient Registers: Page 10
      4. 7.2.4  Programmable Coefficient Registers: Page 11
      5. 7.2.5  Programmable Coefficient Registers: Page 15
      6. 7.2.6  Programmable Coefficient Registers: Page 16
      7. 7.2.7  Programmable Coefficient Registers: Page 17
      8. 7.2.8  Programmable Coefficient Registers: Page 18
      9. 7.2.9  Programmable Coefficient Registers: Page 19
      10. 7.2.10 Programmable Coefficient Registers: Page 25
      11. 7.2.11 Programmable Coefficient Registers: Page 26
      12. 7.2.12 Programmable Coefficient Registers: Page 27
      13. 7.2.13 Programmable Coefficient Registers: Page 28
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Application
      2. 8.2.2 Design Requirements
      3. 8.2.3 Detailed Design Procedure
      4. 8.2.4 Typical Characteristics
      5. 8.2.5 Example Device Register Configuration Script for EVM Setup
    3. 8.3 Power Supply Recommendations
      1. 8.3.1 IOVDD_IO_MODE for 1.8V and 1.2V Operation
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Documentation Support
      1. 9.1.1 Related Documentation
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

7.2 Programmable Coefficient Registers

The register pages in this section consists of the programmable coefficients of the device. TI recommends using the PPC3 GUI for configuring the programmable coefficients settings; for more details see the TAx5x1x-Q1EVM-PDK Evaluation module user's guide and the PurePath™ console graphical development suite. To optimize the coefficients register transaction time for the register pages in this section, the device also supports (by default) auto-incremented pages for the I2C and SPI burst writes and reads. After a transaction of register address 0x7F, the device auto increments to the next page at register 0x08 to transact the next coefficient value. These programmable coefficients are 32-bit, two’s complement numbers. For a successful coefficient register transaction, the host device must write and read all four bytes starting with the most significant byte (BYT1) for a target coefficient register transaction. When using SPI for a coefficient register read transaction, the device transmits the first byte as a dummy read byte; therefore, the host must read five bytes, including the first dummy read byte and the last four bytes corresponding to the coefficient register value starting with the most significant byte (BYT1).