SLLSFF0A December   2021  – April 2026 TCAN1167-Q1

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configurations and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 ESD Ratings IEC Specification
    4. 5.4 Recommended Operating Conditions
    5. 5.5 Thermal Information
    6. 5.6 Power Supply Characteristics
    7. 5.7 Electrical Characteristics
    8. 5.8 Switching Characteristics
    9. 5.9 Typical Characteristics
  7. 6 Parameter Measurement Information
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  VSUP Pin
      2. 7.3.2  VCCOUT Pin
      3. 7.3.3  Digital Inputs and Outputs
      4. 7.3.4  GND
      5. 7.3.5  INH Pin
      6. 7.3.6  WAKE Pin
      7. 7.3.7  nRST Pin
      8. 7.3.8  SDO
      9. 7.3.9  nCS Pin
      10. 7.3.10 SCLK
      11. 7.3.11 SDI
      12. 7.3.12 CAN Bus Pins
      13. 7.3.13 Local Faults
        1. 7.3.13.1 TXD Dominant Timeout (TXD DTO)
        2. 7.3.13.2 Thermal Shutdown (TSD)
        3. 7.3.13.3 Under/Over Voltage Lockout
        4. 7.3.13.4 Unpowered Devices
        5. 7.3.13.5 Floating Terminals
        6. 7.3.13.6 CAN Bus Short Circuit Current Limiting
        7. 7.3.13.7 Sleep Wake Error Timer
      14. 7.3.14 Watchdog
        1. 7.3.14.1 Watchdog Error Counter
        2. 7.3.14.2 Watchdog SPI Control Programming
        3. 7.3.14.3 Watchdog Timing
        4. 7.3.14.4 Question and Answer Watchdog
          1. 7.3.14.4.1 WD Question and Answer Basic information
          2. 7.3.14.4.2 Question and Answer Register and Settings
          3. 7.3.14.4.3 WD Question and Answer Value Generation
        5. 7.3.14.5 Question and Answer WD Example
          1. 7.3.14.5.1 Example configuration for desired behavior
          2. 7.3.14.5.2 Example of performing a question and answer sequence
      15. 7.3.15 Bus Fault Detection and Communication
    4. 7.4 Device Functional Modes
      1. 7.4.1 Operating Mode Description
        1. 7.4.1.1 Normal Mode
        2. 7.4.1.2 Silent Mode
        3. 7.4.1.3 Standby Mode
        4. 7.4.1.4 Sleep Mode
          1. 7.4.1.4.1 Remote Wake Request via Wake-Up Pattern (WUP)
          2. 7.4.1.4.2 Local Wake-Up (LWU) via WAKE Input Terminal
        5. 7.4.1.5 Reset Mode
        6. 7.4.1.6 Fail-safe Mode
      2. 7.4.2 CAN Transceiver
        1. 7.4.2.1 CAN Transceiver Operation
        2. 7.4.2.2 CAN Transceiver Modes
          1. 7.4.2.2.1 CAN Off Mode
          2. 7.4.2.2.2 CAN Autonomous: Inactive and Active
          3. 7.4.2.2.3 CAN Active
        3. 7.4.2.3 Driver and Receiver Function Tables
        4. 7.4.2.4 CAN Bus States
    5. 7.5 Programming
      1. 7.5.1 Serial Peripheral Interface (SPI) Communication
      2. 7.5.2 Serial Clock Input (SCLK)
      3. 7.5.3 Serial Data Input (SDI)
      4. 7.5.4 Serial Data Output (SDO)
      5. 7.5.5 Chip Select Not (nCS)
      6. 7.5.6 Registers
        1. 7.5.6.1  DEVICE_ID_y Register (Address = 0h + formula) [reset = xxh]
        2. 7.5.6.2  REV_ID_MAJOR Register (Address = 8h) [reset = 00h]
        3. 7.5.6.3  REV_ID_MINOR Register (Address = 9h) [reset = 00h]
        4. 7.5.6.4  SPI_RSVD_x Register (Address = Ah + formula) [reset = 00h]
        5. 7.5.6.5  Scratch_Pad_SPI Register (Address = Fh) [reset = 00h]
        6. 7.5.6.6  MODE_CNTRL Register (Address = 10h) [reset = 04h]
        7. 7.5.6.7  WD_CONFIG_1 Register (Address = 13h) [reset = 54h]
        8. 7.5.6.8  WD_CONFIG_2 Register (Address = 14h) [reset = 02h]
        9. 7.5.6.9  WD_INPUT_TRIG Register (Address = 15h) [reset = 00h]
        10. 7.5.6.10 WD_QA_CONFIG Register (Address = 2Dh) [reset = 0h]
        11. 7.5.6.11 WD_QA_ANSWER Register (Address = 2Eh) [reset = 0h]
        12. 7.5.6.12 WD_QA_QUESTION Register (Address = 2Fh) [reset = 0h]
        13. 7.5.6.13 STATUS (address = 40h) [reset = 00h]
        14. 7.5.6.14 INT_GLOBAL Register (Address = 50h) [reset = 0h]
        15. 7.5.6.15 INT_1 Register (Address = 51h) [reset = 0h]
        16. 7.5.6.16 INT_2 Register (Address = 52h) [reset = 40h]
        17. 7.5.6.17 INT_3 Register (Address 53h) [reset = 0h]
        18. 7.5.6.18 INT_CANBUS Register (Address = 54h) [reset = 0h]
        19. 7.5.6.19 INT_ENABLE_1 Register (Address = 56h) [reset = F3h]
        20. 7.5.6.20 INT_ENABLE_2 Register (Address = 57h) [reset = 3Fh]
        21. 7.5.6.21 INT_ENABLE_3 Register (Address =58h) [reset = 80h]
        22. 7.5.6.22 INT_ENABLE_CANBUS Register (Address = 59h) [reset = 7Fh]
        23. 7.5.6.23 INT_RSVD_y Register (Address = 5Ah + formula) [reset = 00h]
  9. 8 Application Information Disclaimer
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
        1. 8.2.1.1 Bus Loading, Length and Number of Nodes
      2. 8.2.2 Detailed Design Procedures
        1. 8.2.2.1 CAN Termination
    3. 8.3 Application Curves
    4. 8.4 Power Supply Requirements
    5. 8.5 Layout
      1. 8.5.1 Layout Guidelines
      2. 8.5.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Receiving Notification of Documentation Updates
    2. 9.2 Support Resources
    3. 9.3 Trademarks
    4. 9.4 Electrostatic Discharge Caution
    5. 9.5 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

10 Revision History

Changes from Revision * (December 2021) to Revision A (April 2026)

  • Changed SDI to pin 11 and SDO to pin 6 in the Functional Block Diagram Go
  • Added the TCAN1167-Q1 Diagram Go
  • Changed SDI to pin 11 and SDO to pin 6 in Figure 7-1 Go
  • Changed Fault 1 to Reserved in Table 7-10 Go
  • Removed the Fault 1 diagrams in Figure 7-8 Go
  • Changed bit 6 to Reserved in Table 7-11 Go