SLUU885C March   2012  – June 2024 UCD3138 , UCD3138064 , UCD3138064A , UCD3138128 , UCD3138A , UCD3138A64

1.   1
2.   2
3.   Abstract
4. 1 Introduction
5. 2 Description
   1. 2.1 Typical Applications
   2. 2.2 Features
6. 3 Electrical Performance Specifications
7. 4 Schematics
8. 5 Test Setup
   1. 5.1 Test Equipment
   2. 5.2 Recommended Test Setup
9. 6 List of Test Points
10. 7 List of Terminals
11. 8 Test Procedure
    1. 8.1 Efficiency Measurement Procedure
    2. 8.2 Equipment Shutdown
12. 9 Performance Data and Typical Characteristic Curves
    1. 9.1 Efficiency
    2. 9.2 Power Factor
    3. 9.3 Total Harmonic Distortion (THD)
    4. 9.4 Input Current at 230 VAC and 50 Hz
    5. 9.5 Output Voltage Ripple
    6. 9.6 Output Turn On
    7. 9.7 Total Harmonic Distortion (THD)
    8. 9.8 Other Waveforms
13. 10EVM Assembly Drawing and PCB Layout
14. 11List of Materials
15. 12Digital PFC Description
    1. 12.1  1PFC Block Diagram
       1. 12.1.1 Single-Phase PFC Block Diagram
       2. 12.1.2 2-Phase PFC Block Diagram
       3. 12.1.3 Bridgeless PFC Block Diagram
    2. 12.2  UCD3138 Pin Definition
       1. 12.2.1 UCD3138 Pin Definition in Single-Phase PFC
       2. 12.2.2 UCD3138 Pin Definition in 2-Phase PFC
       3. 12.2.3 UCD3138 Pin Definition in Bridgeless PFC
    3. 12.3  EVM Hardware – Introduction
       1. 12.3.1 PFC Pre-Regulator Input
       2. 12.3.2 PFC Power Stage
       3. 12.3.3 Non-Isolated UART Interface
       4. 12.3.4 Isolated UART Interface
       5. 12.3.5 Interface Connector of Control Card
       6. 12.3.6 UCD3138 Resource Allocation for PFC Control
    4. 12.4  EVM Firmware – Introduction
       1. 12.4.1 Background Loop
       2. 12.4.2 Voltage Loop Configuration
       3. 12.4.3 Current Loop Configuration
       4. 12.4.4 Interrupts
    5. 12.5  State Machine
    6. 12.6  PFC Control Firmware
    7. 12.7  System Protection
       1. 12.7.1 Cycle-by-Cycle Current Protection (CBC)
       2. 12.7.2 Over-Voltage Protection (OVP)
    8. 12.8  PFC System Control
       1. 12.8.1 Average Current Mode Control
       2. 12.8.2 ZVS and Valley Control
    9. 12.9  Current Feedback Control Compensation Using PID Control
       1. 12.9.1 Loop Compensation from Poles and Zeros in s-Domain
       2. 12.9.2 Feedback Loop Compenstaion Tuning with PID Coefficients
       3. 12.9.3 Feedback Loop Compensation with Multiple-Set of Parameters
    10. 12.10 Voltage Feedback Loop
16. 13Evaluating the Single-Phase PFC with GUI
    1. 13.1 Graphical User Interface (GUI)
    2. 13.2 Open the Designer GUI
    3. 13.3 Overview of the Designer GUI
       1. 13.3.1 Monitor
       2. 13.3.2 Status
       3. 13.3.3 Design and Configure
17. 14Monitoring, Re-configuring and Re-tuning with Designer GUI
    1. 14.1 Power On and Test Procedure
    2. 14.2 Monitoring with GUI
    3. 14.3 Configuration and Re-configuring with GUI
    4. 14.4 Feedback Control Loop Tuning and Re-Tuning with GUI
       1. 14.4.1 Current Loop Evaluation
       2. 14.4.2 Current Loop Re-Tuning
       3. 14.4.3 Voltage Loop Evaluation and Re-tuning
18. 15Digital PFC Firmware Development
19. 16References
20. 17Revision History

IMPORTANT NOTICE AND DISCLAIMER

TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.

These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources.

TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 

Copyright © 2024, Texas Instruments Incorporated