SLVSI28 December   2025 TPS1HC04-Q1

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison Table
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 SNS Timing Characteristics
    7. 6.7 Switching Characteristics
    8. 6.8 Typical Characteristics
  8. 7 Parameter Measurement Information
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Input Voltage Thresholds
      2. 8.3.2  Accurate Current Sense
        1. 8.3.2.1 SNS Response Time
        2. 8.3.2.2 SNS Output Filter
        3. 8.3.2.3 Multiplexing of Current Sense Across Devices
      3. 8.3.3  Overcurrent Protection
        1. 8.3.3.1 Adjustable Current Limit
          1. 8.3.3.1.1 Current Limiting With Thermal Regulation
          2. 8.3.3.1.2 Current Limiting With No Thermal Regulation
          3. 8.3.3.1.3 Current Limit Foldback
          4. 8.3.3.1.4 Current Limit Accuracy
        2. 8.3.3.2 Thermal Shutdown
          1. 8.3.3.2.1 Relative Thermal Shutdown
          2. 8.3.3.2.2 Absolute Thermal Shutdown
      4. 8.3.4  Retry Protection Mechanism From Thermal Shutdown
      5. 8.3.5  Inductive-Load Switching-Off Clamp
      6. 8.3.6  Slower Slew Rate Option
      7. 8.3.7  Capacitive Load Charging
        1. 8.3.7.1 Adjustable Current Limiting for Inrush Control
        2. 8.3.7.2 Current Limit with Thermal Regulation for Capacitive Loads
        3. 8.3.7.3 Retry Thermal Shutdown Behavior for Capacitive Loads
        4. 8.3.7.4 Impact of DC Load on Capacitive Charging Capability
        5. 8.3.7.5 Device Capability
      8. 8.3.8  Bulb Charging
        1. 8.3.8.1 Non-Thermal Regulated Mode for Bulb Loads
        2. 8.3.8.2 Thermal Management During Bulb Inrush
        3. 8.3.8.3 Device Capability
      9. 8.3.9  Fault Detection and Reporting
        1. 8.3.9.1 Diagnostic Enable Function
        2. 8.3.9.2 FLT Reporting
        3. 8.3.9.3 FLT Timings
        4. 8.3.9.4 Fault Table
      10. 8.3.10 Full Diagnostics
        1. 8.3.10.1 Open-Load Detection
          1. 8.3.10.1.1 Channel On
          2. 8.3.10.1.2 Channel Off
        2. 8.3.10.2 Short-to-Battery Detection
        3. 8.3.10.3 Reverse-Polarity and Battery Protection
      11. 8.3.11 Full Protections
        1. 8.3.11.1 UVLO Protection
        2. 8.3.11.2 Loss of GND Protection
        3. 8.3.11.3 Loss of Power Supply Protection
        4. 8.3.11.4 Reverse Current Protection
        5. 8.3.11.5 Protection for MCU I/Os
    4. 8.4 Device Functional Modes
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 EMC Transient Disturbances Test
      3. 9.2.3 Transient Thermal Performance
      4. 9.2.4 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Examples
        1. 9.4.2.1 Without a GND Network
        2. 9.4.2.2 With a GND Network
      3. 9.4.3 Wettable Flank Package
  11. 10Device and Documentation Support
    1. 10.1 Third-Party Products Disclaimer
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 Support Resources
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

9.2.4 Application Curves

The subscript "1" is sometimes used to refer the device channel in few images below.

TPS1HC04-Q1 Turn-on with Resistive Load
VBB = 13.5V ZOUT1 = 19Ω TAMB = 25°C
Figure 9-3 Turn-on with Resistive Load
TPS1HC04-Q1 Turn-off with Resistive Load
VBB = 13.5V ZOUT1 = 19Ω TAMB = 25°C
Figure 9-4 Turn-off with Resistive Load
TPS1HC04-Q1 Rising Slew Rate (D, B version)
VBB = 13.5V IOUT1 = 11A TAMB = 25°C
VEN = 0V to 5V
Figure 9-5 Rising Slew Rate (D, B version)
TPS1HC04-Q1 Rising Slew Rate (P, M version)
VBB = 13.5V IOUT1 = 5A TAMB = 25°C
VEN = 0V to 5V
Figure 9-7 Rising Slew Rate (P, M version)
TPS1HC04-Q1 Device Turn-on Behavior with Output Shorted to GND
VBB = 13.5V VOUT1 = STG TAMB = 125°C
ILIM = STG VEN1 = 5V
Figure 9-9 Device Turn-on Behavior with Output Shorted to GND
TPS1HC04-Q1 Hot Short (Retry behavior)
VBB = 13.5V ZOUT1 = 1uH + 100mΩ TAMB = 125°C
VEN1 = 5V
Figure 9-11 Hot Short (Retry behavior)
TPS1HC04-Q1 Falling Slew Rate (D, B version)
VBB = 13.5V IOUT1 = 11A TAMB = 25°C
VEN = 5V to 0V
Figure 9-6 Falling Slew Rate (D, B version)
TPS1HC04-Q1 Falling Slew Rate (P, M version)
VBB = 13.5V IOUT1 = 5A TAMB = 25°C
VEN = 5V to 0V
Figure 9-8 Falling Slew Rate (P, M version)
TPS1HC04-Q1 Open Load Detection Delay with Open Load Fault on the device (P, D version)
VBB = 13.5V VOUT = open load TAMB = 25°C
DIAG_EN = PWM (200Hz) VEN1 = 0V
SNS outputs ISNSFH current when DIAG_EN is high and is floating when DIAG_EN is low
FLT = get asserts when DIAG_EN is high
Figure 9-10 Open Load Detection Delay with Open Load Fault on the device (P, D version)
TPS1HC04-Q1 Hot Short (Retry behavior) zoomed to initial retry window
VBB = 13.5V ZOUT1 = 1uH + 100mΩ TAMB = 25°C
VEN1 = 5V
Figure 9-12 Hot Short (Retry behavior) zoomed to initial retry window