SNLU226B February   2018  – April 2021 DS90UB960-Q1

 

  1. 1 Introduction
  2. 2 Features
  3. 3 Application Diagram
  4. 4 Major Components
  5. 5 Quick Start Guide
  6. 6 Board Connections
    1. 6.1 Power Supply
    2. 6.2 Power Over Coax Interface
    3. 6.3 MIPI CSI-2 Output Signals
    4. 6.4 FPD-Link III Signals
    5. 6.5 I2C Interface
    6. 6.6 Control Interface
  7. 7 Enable and Reset
  8. 8 ALP Software Setup
    1. 8.1  System Requirements
    2. 8.2  Download Contents
    3. 8.3  Installation of the ALP Software
    4. 8.4  Startup - Software Description
    5. 8.5  Information Tab
    6. 8.6  Registers Tab
    7. 8.7  Registers Tab - Address 0x00 Selected
    8. 8.8  Registers Tab - Address 0x00 Expanded
    9. 8.9  Scripting Tab
    10. 8.10 Sample ALP Python Script
      1. 8.10.1 Initialization
  9. 9 Troubleshooting ALP Software
    1. 9.1 ALP Loads the Incorrect Profile
    2. 9.2 ALP does not detect the EVM
  10. 10Typical Connection and Test Equipment
  11. 11Termination Device
  12. 12Typical Test Setup
  13. 13Equipment References
  14. 14Cable References
  15. 15Bill of Materials
  16. 16PCB Schematics
  17. 17Board Layout
  18. 18Revision History

6.6 Control Interface

Table 6-12 VDDIO Interface Header - J1
ReferenceSignalDescription
J4VDDIOSelects VDDIO bus voltage
Short pins 1-2: 3.3V IO (Default)
Short pins 2-3: 1.8V IO
Table 6-13 GPIO Interface Header - J8
ReferenceSignalDescription
J8.2GPIO0General Purpose Input/Output 0
J8.4GPIO1General Purpose Input/Output 1
J8.6GPIO2General Purpose Input/Output 2
J8.8GPIO3General Purpose Input/Output 3
J8.10GPIO4General Purpose Input/Output 4
J8.12GPIO5General Purpose Input/Output 5
J8.14GPIO6General Purpose Input/Output 6
J8.16GPIO7General Purpose Input/Output 7
Table 6-14 CMLOUTP Output Signals
ReferenceSignalDescription
TP1CMLOUTPTest Pad for Channel Monitor Loop-through Driver
TP2CMLOUTNTest Pad for Channel Monitor Loop-through Driver
Table 6-15 Mode SW-DIP4 - S1
ReferenceModeDescription
S1.11CSI Mode (DS90UB953 compatible) (Default)
S1.22RAW12 / LF (DS90UB913A / 933 compatible)
S1.33RAW12 / HF (DS90UB913A / 933 compatible)
S1.44RAW10 (DS90UB913A / 933 compatible)
Table 6-16 Control SW-DIP2 - SW1
ReferenceSignalInput = LInput = HDescription
SW1.1TESTENFor Normal operation (Default)Test Mode enableTest Mode
SW1.2PDBDevice is powered downDevice is enabled (Default)Power-down Mode
Table 6-17 LEDs
ReferenceLED NameDescription
D1GPIO0Illuminates if GPIO0 is ON
D2GPIO1Illuminates if GPIO1 is ON
D3GPIO2Illuminates if GPIO2 is ON
D4GPIO3Illuminates if GPIO3 is ON
D5GPIO4Illuminates if GPIO48 is ON
D6GPIO5Illuminates if GPIO5 is ON
D7GPIO6Illuminates if GPIO6 is ON
D8GPIO7Illuminates if GPIO7 is ON
D11VDD_EXTIlluminates if 12V Power is applied to DC-IN J30
D12VDD5VIlluminates on +5V
D13VFEED_POCIlluminates if VFEED_POC Power is ON
D14VDDIOIlluminates on VDDIO Power