SNOS751F April   2000  – June 2026 LM6132 , LM6134

PRODUCTION DATA  

  1.   1
  2. 1Features
  3. 2Applications
  4. 3Description
  5. 4Pin Configuration and Functions
  6. 5Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information LM6132
    5. 5.5  Thermal Information LM6134
    6. 5.6  Electrical Characteristics: VS = 5V
    7. 5.7  Electrical Characteristics: VS = 2.7V
    8. 5.8  Electrical Characteristics: VS = 24V
    9. 5.9  Typical Characteristics
    10. 5.10 Old Versus New Die Comparison
  7. 6Application and Implementation
    1. 6.1 Application Information
    2. 6.2 Typical Applications
      1. 6.2.1 Three Op Amp Instrumentation Amp with Rail-to-Rail Input and Output
      2. 6.2.2 Flat Panel Display Buffering
  8. 7Device and Documentation Support
    1. 7.1 Receiving Notification of Documentation Updates
    2. 7.2 Support Resources
    3. 7.3 Trademarks
    4. 7.4 Electrostatic Discharge Caution
    5. 7.5 Glossary
  9. 8Revision History
  10. 9Mechanical, Packaging, and Orderable Information

8 Revision History

Changes from Revision E (September 2014) to Revision F (June 2026)

  • Deleted "Swing 0.01V to 4.99V" in Features Go
  • Deleted Supply Current vs. Supply Voltage plotGo
  • Deleted Offset Voltage vs. Supply Voltage plotGo
  • Added Functional Block DiagramGo
  • Updated table note 3 in Absolute Maximum Ratings Go
  • Changed from (V–) – 0.3V to (V–) – 0.5VGo
  • Changed from (V+) + 0.3V to (V+) + 0.5VGo
  • Updated table note 4 in Absolute Maximum Ratings Go
  • Updated table note 2 in Absolute Maximum Ratings Go
  • Changed from ±25mA to ContinuousGo
  • Changed rating from Current at Output Pin to Output short circuitGo
  • Added Operating ambient temperature ratingGo
  • Added CDM ESD ratingGo
  • Updated table note in ESD Ratings Go
  • Added table note in ESD Ratings Go
  • Deleted table note 1 in Recommended Operating Conditions Go
  • Changed minimum supply voltage from 1.8V to 2.7VGo
  • Changed Junction-to-case thermal resistance for LM6132D from 193℃/W to 127.1℃/WGo
  • Changed Junction-to-case thermal resistance for LM6132P from 115℃/W to 84.45℃/WGo
  • Added Junction-to-case (top) thermal resistance for packagesGo
  • Added Junction-to-board thermal resistance for packagesGo
  • Added Junction-to-top characterization parameter for packagesGo
  • Added Junction-to-board characterization parameter for packagesGo
  • Changed Junction-to-case thermal resistance for LM6134D from 126℃/W to 82.48℃/WGo
  • Updated all Electrical Characteristics tables to latest formatGo
  • Updated Output Swing format to refer to railsGo
  • Changed typical voltage output swing for 100kΩ load from 4.992V to 30mV from positive rail Go
  • Changed maximum voltage output swing for 100kΩ load from 4.98V to 40mV from positive railGo
  • Changed typical voltage output swing for 100kΩ load from 0.007V to 30mV from negative railGo
  • Changed maximum voltage output swing for 100kΩ load from 0.017V to 35mV from negative railGo
  • Changed maximum voltage output swing for 100kΩ load over temperature from 0.019V to 50mV from negative railGo
  • Deleted table notes for all Electric Characteristic tablesGo
  • Updated Output Swing format to refer to railsGo
  • Updated Output Swing format to refer to railsGo
  • Added CMRR and PSRR vs Frequency plot for new dieGo
  • Added Gain and Phase vs Frequency plot for new dieGo
  • Added a new sub-section Old Versus New Die Comparison Go
  • Deleted sub-section Enhanced Slew Rate Go

Changes from Revision D (February 2013) to Revision E (September 2014)

  • Updated the numbering format for tables, figures, and cross-references throughout the documentGo

Changes from Revision C (February 2013) to Revision D (February 2013)

  • Changed layout of National Semicondutor Data Sheet to TI formatGo