SNOSDG7A May   2025  – March 2026 TPS7H6101-SEP

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Options Table
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Switching Characteristics
    7. 6.7 Typical Characteristics
  8. 7 Parameter Measurement Information
    1. 7.1 Timing Measurement
    2. 7.2 Deadtime Measurement Information
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Gate Drive Input Voltage
      2. 8.3.2  Linear Regulator Operation
      3. 8.3.3  Bootstrap Operation
        1. 8.3.3.1 Bootstrap Charging Methods
          1. 8.3.3.1.1 Internal Bootstrap Charging
          2. 8.3.3.1.2 Direct VIN Bootstrap Charging
          3. 8.3.3.1.3 Dual Bootstrap Charging
          4. 8.3.3.1.4 Two Switch Common Ground Reference
        2. 8.3.3.2 Bootstrap Capacitor
        3. 8.3.3.3 Bootstrap Diode
        4. 8.3.3.4 Bootstrap Resistor
      4. 8.3.4  High-Side Driver Startup
      5. 8.3.5  PWM_LI and EN_HI
      6. 8.3.6  Dead Time
      7. 8.3.7  Input Interlock Protection
      8. 8.3.8  Undervoltage Lockout and Power Good (PGOOD)
      9. 8.3.9  Negative Switch Node Voltage Transients
      10. 8.3.10 Level Shifter
    4. 8.4 Device Functional Modes
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Bootstrap and Bypass Capacitor
          1. 9.2.2.1.1 Bootstrap Capacitor
          2. 9.2.2.1.2 Input Capacitance
          3. 9.2.2.1.3 Internal Regulator Capacitor
        2. 9.2.2.2 Bootstrap Diode
      3. 9.2.3 Application Results
      4. 9.2.4 Double Pulse Characteristics
        1. 9.2.4.1 Double Pulse Testing Measurement
        2. 9.2.4.2 Double Pulse Testing Results
      5. 9.2.5 Thermal Characteristics
        1. 9.2.5.1 Foster RC Thermal Model
        2. 9.2.5.2 Applying Foster Thermal Networks
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
        1. 9.4.1.1 Thermal Vias
        2. 9.4.1.2 HVIN Plane
        3. 9.4.1.3 Solder Mask Defined Pads
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 Support Resources
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information
8.3.3.1.3 Dual Bootstrap Charging

Figure 8-2 shows the dual-charging option, which is a combination of the bootstrap switch and direct VIN charging methods. This method offers the benefit of circumventing any potential bootstrap charging issues during startup due to the low-side FET not turning on, while also taking advantage of the reduction of bootstrap voltage during normal operation offered by the internal switch. The series resistor used with the bootstrap diode in the direct VIN charging path must be higher than the resistance of the internal bootstrap switch to facilitate that the charging is conducted via the bootstrap switch during normal operation. This higher resistor value also effectively reduces the Zener current during normal operation. The trade-off for this configuration is the additional part count.

TPS7H6101-SEP Dual Bootstrap Charging Configuration Figure 8-4 Dual Bootstrap Charging Configuration