SNVSCF8A June   2023  – October 2026 TPS3436

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Thermal Information
    6. 6.6  Electrical Characteristics
    7. 6.7  Timing Requirements
    8. 6.8  Switching Characteristics
    9. 6.9  Timing Diagrams
    10. 6.10 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagrams
    3. 7.3 Feature Description
      1. 7.3.1 Window Watchdog Timer
        1. 7.3.1.1 tWC (Close Window) Timer
        2. 7.3.1.2 tWO (Open Window) Timer
        3. 7.3.1.3 Watchdog Enable Disable Operation
        4. 7.3.1.4 tSD Watchdog Start Up Delay
        5. 7.3.1.5 SET Pin Behavior
      2. 7.3.2 Manual RESET
      3. 7.3.3 WDO Output
    4. 7.4 Device Functional Modes
  9. 8 Application and Implementation
    1. 8.1 Application Information
      1. 8.1.1 Output Assert Delay
        1. 8.1.1.1 Factory-Programmed Output Assert Delay Timing
        2. 8.1.1.2 Adjustable Capacitor Timing
      2. 8.1.2 Watchdog Window Functionality
        1. 8.1.2.1 Factory-Programmed Timing Options
        2. 8.1.2.2 Adjustable Capacitor Timing
    2. 8.2 Typical Applications
      1. 8.2.1 Design 1: Monitoring a Microcontroller Watchdog During Operational and Sleep Modes
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
          1. 8.2.1.2.1 Determining Window Timings During Operation and Sleep Modes
          2. 8.2.1.2.2 Meeting the Output Assert Delay
          3. 8.2.1.2.3 Setting the Watchdog Window
          4. 8.2.1.2.4 Calculating the WDO Pullup Resistor
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Device Nomenclature
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

tWO (Open Window) Timer

The window watchdog frame consists of two sub frames tWC followed by tWO. The host is expected to drive valid WDI transition during tWO time. A valid WDI transition before beginning of tWO frame causes early fault condition. Failure to offer valid WDI transition during tWC and tWO frames results in late fault condition. When a fault condition is detected the WDO output is asserted.

The tWO value is derived using tWC value and the window open time ratio value n. Equation highlights the relationship between tWO and tWC. Refer Section 4 to select available ratio options.

Equation 6. t W O = ( n - 1 ) × t W C

Each orderable can offer up to 3 ratio options based on the available SET pins. Refer Section 7.3.1.5 to identify mapping of ratio value to SET pin control. The maximum tWO value is limited to 640 seconds. Make sure selected tWC and ratio combination does not lead to tWO value greater than 640 seconds.