SPRUJA2B November   2023  – August 2026

1.   1
2.   Description
3.   Get Started
4.   Features
5.   5
6. 1Evaluation Module Overview
   1. 1.1 Introduction
   2. 1.2 Kit Contents
   3. 1.3 Device Information
   4. 1.4 EVM Revisions and Assembly Variants
   5. 1.5 Specification
7. 2Hardware
   1. 2.1  Additional Images
   2. 2.2  Key Features
      1. 2.2.1 Processor
      2. 2.2.2 Power Supply
      3. 2.2.3 Memory
      4. 2.2.4 JTAG/Emulator
      5. 2.2.5 Supported Interfaces and Peripherals
      6. 2.2.6 Expansion Connectors/Headers
   3. 2.3  Power Requirement
   4. 2.4  Power ON/OFF Procedure
      1. 2.4.1 Power ON Procedure
      2. 2.4.2 Power OFF Procedure
      3. 2.4.3 Test Points
      4. 2.4.4 Power Indication LED
   5. 2.5  Interface Mapping
   6. 2.6  Clocking
      1. 2.6.1 Peripheral Ref Clock
   7. 2.7  Reset
   8. 2.8  Camera Serial Interface (CSI)
   9. 2.9  Open LVDS Display Interface (OLDI)
   10. 2.10 Display Serial Interface (DSI)
   11. 2.11 Audio Codec Interface
   12. 2.12 HDMI Display
   13. 2.13 JTAG Interface
   14. 2.14 Test Automation Header
   15. 2.15 UART Interface
   16. 2.16 USB Interface
       1. 2.16.1 USB 2.0 Type A Interface
       2. 2.16.2 USB 2.0 Type-C® Interface
   17. 2.17 Memory Interfaces
       1. 2.17.1 LPDDR4 Interface
       2. 2.17.2 Octal Serial Peripheral Interface (OSPI)
       3. 2.17.3 MMC Interfaces
          1. 2.17.3.1 MMC0 - eMMC Interface
          2. 2.17.3.2 MMC1 - Micro SD Interface
          3. 2.17.3.3 MMC2 - M.2 Key E Interface
       4. 2.17.4 Board ID EEPROM
   18. 2.18 Ethernet Interface
       1. 2.18.1 CPSW Ethernet PHY Strapping
       2. 2.18.2 CPSW Ethernet PHY1 Default Configuration
       3. 2.18.3 CPSW Ethernet PHY2 Default Configuration
   19. 2.19 GPIO Port Expander
   20. 2.20 GPIO Mapping
   21. 2.21 Power
       1. 2.21.1 Power Input
       2. 2.21.2 Power Supply
       3. 2.21.3 Power Sequencing
       4. 2.21.4 AM62P SoC Power
       5. 2.21.5 Current Monitoring
   22. 2.22 EVM User Setup and Configuration
       1. 2.22.1 DIP Switches
       2. 2.22.2 Boot Modes
       3. 2.22.3 User Test LEDs
   23. 2.23 Expansion Headers
       1. 2.23.1 User Expansion Connector
       2. 2.23.2 MCU Connector
       3. 2.23.3 GPMC NAND (x8) Connector
   24. 2.24 Interrupt
   25. 2.25 I2C Address Mapping
8. 3Hardware Design Files
9. 4Compliance Information
   1. 4.1 Compliance and Certifications
10. 5Additional Information
    1. 5.1 Known Hardware or Software Issues
       1. 5.1.1 Issue 1 - Watchdog Reset
       2. 5.1.2 Issue 2 - Power Down Sequence
       3. 5.1.3 Issue 3 - Power Cycling Failure Using TIVA
    2. 5.2 Trademarks
    3.     81
11. 6References
12. 7Revision History