SWRU647 September   2026

 

  1.   1
  2.   Description
  3.   Features
  4. 1Evaluation Module Overview
    1. 1.1 Introduction
    2. 1.2 Key Features
    3. 1.3 Kit Contents
    4. 1.4 Specification
    5. 1.5 Device Information
  5. 2Hardware
    1. 2.1  AWRL6888EVM Antenna
      1. 2.1.1 PCB Material
        1. 2.1.1.1 Transmitter and Receiver Virtual Array
    2. 2.2  EVM Mux Block Diagram
    3. 2.3  Switch Settings
    4. 2.4  Push Button Switches
    5. 2.5  LEDs
    6. 2.6  DC Input Jack
    7. 2.7  USB Connector
    8. 2.8  DCA1000 HD Connector
    9. 2.9  BoosterPack Connector for LaunchPad Connectivity
    10. 2.10 CAN-FD_A Connector
    11. 2.11 CAN-FD_B Connector
    12. 2.12 LIN-PHY Connector
    13. 2.13 I2C Connections
      1. 2.13.1 EEPROM
    14. 2.14 XDS110 Interface
    15. 2.15 FTDI Interface
    16. 2.16 DCA1000EVM Mode
    17. 2.17 PCB Storage and Handling Recommendations
      1. 2.17.1 PCB Storage and Handling Recommendations
      2. 2.17.2 Higher Power Demanding Applications
  6. 3Software, Development Tools, and Example Code
  7. 4Hardware Design Files
    1. 4.1 Schematics, PCB Layout and Bill of Materials (BOM)
    2. 4.2 EVM Design Database
    3. 4.3 Hardware Design Checklist
  8. 5Additional Information
    1. 5.1 Trademarks
  9. 6References
    1. 6.1 TI E2E Community

Transmitter and Receiver Virtual Array

The transmitter and receiver antenna positions shown in Figure 2-6 form a virtual array of sixteen transmitter and receiver pairs. This allows finer object detections in both azimuth and Elevation planes with an angular resolution of around 15°. Receiver antennas are spaced at distance D (λ/2) apart in azimuth plane. The transmitter antennas are spaced at distance D (λ/2) apart in both azimuth and elevation plane.


AWRL6888EVM Antenna Virtual array with
                    respect to TXs and RXs

Figure 2-6 Antenna Virtual array with respect to TXs and RXs

Figure 2-7 and Figure 2-8 below show the antenna radiation pattern with regard to azimuth and elevation planes. Both figures show the radiation pattern for TX1, TX2, TX3, TX4, TX5, TX6, TX7, TX8 and RX1, RX2, RX3, RX4, RX5, RX6, RX7, RX8 together. All of the measurements were done with a Tx and Rx combination together. Thus, for the -6dB beam width, the user must see a 12dB drop (6dB from Tx and 6dB from Rx)

Note: Wavelength (λ) is computed based on a frequency of 60.5GHz. Antenna placements were made according to this frequency.

AWRL6888EVM AWRL6888EVM Azimuth Antenna
                    Radiation Pattern

Figure 2-7 AWRL6888EVM Azimuth Antenna Radiation Pattern

AWRL6888EVM AWRL6888EVM Elevation Antenna
                    Radiation Pattern

Figure 2-8 AWRL6888EVM Elevation Antenna Radiation Pattern
Note: In accordance with the EN 62311 RF exposure test, a minimum separation distance of 20 centimeters must be maintained between the user and the EVM during operation.