MSP430F5258

ACTIVE

25 MHz MCU with 128KB Flash, 32KB SRAM, Comparator, DMA, UART/SPI/I2C, 1.8V Split-Rail I/O

Top

Product details

Parameters

Features Real-Time Clock Non-volatile memory (kB) 128 RAM (KB) 32 ADC Slope ADC: channels (#) 0 GPIO pins (#) 53 I2C 4 SPI 8 UART 4 Comparator channels (#) 8 Timers - 16-bit 4 Bootloader (BSL) I2C Special I/O 1.8V I/O Operating temperature range (C) -40 to 85 Rating Catalog open-in-new Find other MSP430 ultra-low-power MCUs

Package | Pins | Size

VQFN (RGC) 64 81 mm² 9 x 9 open-in-new Find other MSP430 ultra-low-power MCUs

Features

  • Dual-supply voltage device
    • Primary supply (AVCC, DVCC)
      • Powered from external supply: 3.6 V down to 1.8 V
      • Up to 18 general-purpose I/Os with up to 8 external interrupts
    • Low-voltage interface supply (DVIO)
      • Powered from separate external supply: 1.62 V to 1.98 V
      • Up to 35 general-purpose I/Os with up to 16 external interrupts
      • Serial communications
  • Ultra-low power consumption
    • Active mode (AM): All system clocks active 290 µA/MHz at 8 MHz, 3.0 V, flash program execution (typical) 150 µA/MHz at 8 MHz, 3.0 V, RAM program execution (typical)
    • Standby mode (LPM3): Real-time clock (RTC) with crystal, watchdog, and supply supervisor operational, full RAM retention, fast wakeup: 2.1 µA at 2.2 V, 2.3 µA at 3.0 V (typical) Low-power oscillator (VLO), general-purpose counter, watchdog, and supply supervisor operational, full RAM retention, fast wakeup: 1.6 µA at 3.0 V (typical)
    • Off mode (LPM4): Full RAM retention, supply supervisor operational, fast wakeup: 1.3 µA at 3.0 V (typical)
    • Shutdown mode (LPM4.5): 0.18 µA at 3.0 V (typical)
  • Wake up from standby mode in 3.5 µs (typical)
  • 16-bit RISC architecture, extended memory, up to 25-MHz system clock
  • Flexible power-management system
    • Fully integrated LDO with programmable regulated core supply voltage
    • Supply voltage supervision, monitoring, and brownout
  • Unified clock system
    • FLL control loop for frequency stabilization
    • Low-power low-frequency internal clock source (VLO)
    • Low-frequency trimmed internal reference source (REFO)
    • 32-kHz watch crystals (XT1)
    • HF crystals up to 32 MHz (XT2)
  • 16-bit timer TA0, Timer_A with five capture/compare registers
  • 16-bit timer TA1, Timer_A with three capture/compare registers
  • 16-bit timer TA2, Timer_A with three capture/compare registers
  • 16-bit timer TB0, Timer_B with seven capture/compare shadow registers
  • Four universal serial communication interfaces
    • USCI_A0, A1, A2, A3 each support:
      • Enhanced UART with automatic baud-rate detection
      • IrDA encoder and decoder
      • Synchronous SPI
    • USCI_B0, B1, B2, B3 each support:
      • I2C
      • Synchronous SPI
  • 10-bit analog-to-digital converter (ADC) with internal reference, sample-and-hold
  • comparator
  • Hardware multiplier supports 32-bit operations
  • Serial onboard programming, no external programming voltage needed
  • 3-channel internal DMA
  • Basic timer with RTC feature
  • Device Comparison Summarizes the available family members and packages

All trademarks are the property of their respective owners.

open-in-new Find other MSP430 ultra-low-power MCUs

Description

Using an "always-on" ultra-low-power system controller can significantly reduce power consumption on portable devices like handsets and tablets. These controllers can act as sensor hubs and monitor user stimuli (for example, reading inertial sensors or touch sensors) and vital system parameters like battery health and temperature, while power-hungry application processors and touch screen controllers are turned off. The microcontroller can then "wake up" the system based on a user input or on a fault condition that requires CPU intervention.

The MSP430F525x series is the latest addition to the 1.8-V split-rail I/O portfolio (previously only available on MSP430F522x) and is specifically designed for "always-on" system controller applications. 1.8-V I/O allows for seamless interface to application processors and other devices without the need for external level translation, while the primary supply to the MCU can be on a higher voltage rail.

Compared to the MSP430F522x, the MSP430F525x provides up to four times more RAM (32KB) and double the serial interfaces (four USCI_A and four USCI_B). The MSP430F525x also features four 16-bit timers, a high-performance 10-bit ADC, a hardware multiplier, DMA, a comparator, and an RTC module with alarm capabilities. The MSP430F525x consumes 290 µA/MHz (typical) in active mode running from flash memory, and it consumes 1.6 µA (typical) in standby mode (LPM3). The MSP430F525x can switch to active mode in 3.5 µs (typical), which makes it a great fit for "always-on" low-power applications.

Key benefits of the MSP430F525x are as follows:

  • Up to 32KB of RAM allows complex sensor hub algorithms and high levels of aggregation such as keyboard control and power management.
  • Four USCI_A and four USCI_B modules allow for eight concurrent dedicated hardware serial interfaces (for example, four I2C and four SPI) for fast and robust communication to sensors or peripheral devices.
  • Up to 35 I/Os that can be used in the 1.8-V voltage rail.

For complete module descriptions, see the MSP430F5xx and MSP430F6xx Family User’s Guide . For design guidelines, see Designing With MSP430F522x and MSP430F521x Devices .

open-in-new Find other MSP430 ultra-low-power MCUs
Download
Similar products you might be interested in
open-in-new Compare products
Similar but not functionally equivalent to the compared device:
MSP430F5229 ACTIVE 25 MHz MCU with 128KB Flash, 8KB SRAM, 10-bit ADC, Comparator, DMA, 1.8V Split-Rail I/O This product is a microcontroller with similar split-rail I/O functionalities and fewer serial communication channels.

Technical documentation

= Top documentation for this product selected by TI
No results found. Please clear your search and try again. View all 33
Type Title Date
* Datasheet MSP430F525x Mixed-Signal Microcontrollers datasheet (Rev. D) Oct. 20, 2020
* Errata MSP430F5258 Device Erratasheet (Rev. S) Apr. 24, 2019
* User guide MSP430x5xx and MSP430x6xx Family User's Guide (Rev. Q) Aug. 17, 2018
User guide MSP430 MCUs Development Guide Book Oct. 09, 2020
User guide SYS/BIOS (TI-RTOS Kernel) User's Guide (Rev. V) Jun. 01, 2020
Application note MSP430 System-Level ESD Considerations (Rev. A) Jan. 13, 2020
Application note MSP430 System ESD Troubleshooting Guide Dec. 13, 2019
Application note ESD Diode Current Specification (Rev. A) Jul. 10, 2019
Application note Designing with MSP430F522x and MSP430F521x Devices (Rev. A) Oct. 04, 2018
Application note Interfacing the 3-V MSP430 MCU to 5-V Circuits (Rev. A) Oct. 03, 2018
Application note MSP430F5xx Overview and Comparison to MSP430F2xx and MSP430F4xx (Rev. A) Sep. 26, 2018
Application note Implementing SMBus Using MSP430 Hardware I2C (Rev. B) Sep. 25, 2018
Application note Implementing An Ultra-Low-Power Keypad Interface With MSP430 MCUs (Rev. A) May 22, 2018
Application note Li-Ion Battery Charger Solution Using an MSP430™ MCU (Rev. A) May 18, 2018
Application note MSP430 32-kHz Crystal Oscillators (Rev. D) Jul. 18, 2017
White paper Capacitive Touch and MSP Microcontrollers (Rev. A) Apr. 27, 2017
Application note Migrating from the MSP430F5xx,F6xx Family to the MSP430FR58xx/FR59xx/68xx Family (Rev. D) Nov. 03, 2016
Technical articles “Touching” the smart grid infrastructure space with capacitive sensing technology Mar. 31, 2016
User guide Safety Manual for MSP430G2xx, F5xx, and FR57xx in IEC 60730 Safety Applications (Rev. A) Jan. 12, 2016
Technical articles Don’t miss out on the top training videos of 2015 Dec. 16, 2015
Application note MSP Code Protection Features Dec. 07, 2015
Technical articles How fast is your 32-bit MCU? Jul. 15, 2015
Technical articles Lose power, not data with new FRAM microcontrollers May 20, 2015
Application note Low-Power Pedometer Using an MSP430 MCU May 28, 2013
Application note Enabling Low-Power Windows 8 HID Over I2C Applications Using MSP430 MCUs Nov. 30, 2012
Application note Design Considerations When Using the MSP430 Graphics Library Oct. 05, 2012
Application note Capacitive Touch Sensing and SYS/BIOS Sep. 12, 2012
Application note Heart-Rate Monitor with Micrium uC/OS-II Kernel on the MSP430F5438A Experimenter Jul. 05, 2012
Application note MSP430 Based Lithium-Ion Polymer Battery Charging and Gauging Solution Using USB (Rev. A) Jun. 27, 2012
White paper Power Management Solutions for Ultra-Low-Power 16-Bit MSP430 MCUs (Rev. D) Mar. 28, 2012
Application note Nine-Axis Sensor Fusion Using Direction Cosine Matrix Algorithm on MSP430F5xx (Rev. A) Feb. 13, 2012
Application note Multi-Cell Li-Ion Battery Management System Using MSP430F5529 and bq76PL536 Dec. 16, 2010
Application note 1.8V – 5.5V Input, High-Efficiency DCDC Converter Reference Design for MSP430 (Rev. B) Jun. 14, 2010

Design & development

For additional terms or required resources, click any title below to view the detail page where available.

Hardware development

DEVELOPMENT KIT Download
117
Description

The MSP-TS430RGC64C is a standalone 64-pin ZIF socket target board used to program and debug the MSP430 MCU in-system through the JTAG interface or the Spy Bi-Wire (2-wire JTAG) protocol.

Device Support: The MSP-TS430RGC64C development board supports MSP430F52xx MCUs in a 64-pin QFN package (TI (...)

Features
  • Development board (MSP-TS430RGC64C) with a 64-pin ZIF socket fitting MSP430F52xx derivatives in 64-pin QFN (RGC) packages includes an LED indicator, JTAG adapter, and header pin-outs for prototyping.
  • Supports all debugging interfaces using a standard 14-pin JTAG header such as the MSP-FET430UIF.
HARDWARE PROGRAMMING TOOL Download
115
Description

The MSP-FET is a powerful emulation development tool – often called a debug probe – which allows users to quickly begin development on MSP low-power microcontrollers (MCU).

It supports programming and real-time debugging over both JTAG and SBW interfaces. Furthermore, the MSP-FET also provides a (...)

Features
  • USB debugging interface to connect any MSP430 MCU to a computer for real-time, in-system programming and debugging
  • Enables EnergyTrace™ technology for energy measurement and debugging on all MSP430 and MSP432 devices in the Code Composer Studio and IAR Embedded Workbench development environments
  • (...)
HARDWARE PROGRAMMING TOOL Download
Description

The MSP Gang Programmer (MSP-GANG) is a MSP430™/MSP432™ device programmer that can program up to eight identical MSP430/MSP432 Flash or FRAM devices at the same time. It connects to a host PC using a standard RS-232 or USB connection and provides flexible programming options that allow (...)

Features
  • Quickly and reliably program Flash or FRAM-based MSP devices via RS-232 or USB interface
  • Several programming modes:
    • Interactive Mode – Programming while connected to PC using the MSP GANG Programmer GUI
    • Program from Image – An image can be stored, which contains configuration options and code (...)

Software development

SOFTWARE DEVELOPMENT KIT (SDK) Download
MSP430Ware for MSP Microcontrollers
MSPWARE MSP430Ware is a collection of resources that help users to effectively create and build MSP430 code. These resources support ALL MSP430 microcontrollers (MCUs). As one user mentioned, “It’s essentially everything developers need to become MSP430 microcontroller experts!”

This complete collection of (...)

Features
  • Collection of MSP design resources
  • Available within CCS, as a standalone executable, or as part of TI’s new Cloud-based tools
  • Auto-updates through the web
  • Sleek & intuitive GUI for browsing content
  • Features the MSP Driver Library
  • Automatic filtering of content using a unique 2-pane view
APPLICATION SOFTWARE & FRAMEWORK Download
IEC60730 Software Package
MSP430-IEC60730-SW-PACKAGE The IEC60730 MSP430 software package was developed to be useful in assisting customers in complying with IEC 60730-1:2010 (Automatic Electrical Controls for Household and Similar Use – Part 1: General Requirements) for up to Class B products, which includes home appliances, arc detectors (...)
Features
Supports testing these parts:
  • MSP430G23xx
  • MSP430G24xx
  • MSP430G25xx
  • MSP430G2x44
  • MSP430G2x55
  • MSP430F5xx
  • MSP430FR2433
  • MSP430FR25xx
  • MSP430FR26xx
  • MSP430FR57xx
DRIVER OR LIBRARY Download
Digital Signal Processing (DSP) Library for MSP430 Microcontrollers
MSP-DSPLIB The TI MSP430™ Digital Signal Processing library is a set of optimized functions to perform common signal processing operations for MSP430 microcontrollers. These functions are used in applications where processing-intensive transforms are done in real-time for minimal energy and with very (...)
DRIVER OR LIBRARY Download
MSP Graphics Library
MSP-GRLIB The MSP Graphics Library is a royalty-free set of graphics primitives for displaying images or creating graphical user interfaces (GUIs) on MSP430 and MSP432 microcontroller-based boards that use a graphical display. The graphics library consists of two functional layers: 1) the display driver layer (...)
Features
  • Free license and royalty-free use
  • Simplify and accelerate development of applications
  • Easy-to-maintain code
DRIVER OR LIBRARY Download
Fixed Point Math Library for MSP
MSP-IQMATHLIB The Texas Instruments® MSP IQmath and Qmath Libraries are a collection of highly optimized and high-precision mathematical functions for C programmers to seamlessly port a floating-point algorithm into fixed-point code on MSP430 and MSP432 devices. These routines are typically used in (...)
Features
  • Optimized fixed point functions - reduce development time and enable developers to focus on optimizing application code
  • Up to 100x higher performance when executing common fixed point scalar math functions in CCS – this means the MSP microcontroller can remain in low power modes longer than (...)
DRIVER OR LIBRARY Download
Bootloader (BSL) for MSP low-power microcontrollers
MSPBSL The bootloader (BSL) on MSP430™ microcontrollers (MCUs) lets users communicate with embedded memory in the MSP MCUs during the prototyping phase, final production, and in service. This is done through standard interfaces such as UART, I2C, SPI, and USB. Both the programmable memory (...)
DRIVER OR LIBRARY Download
Floating Point Math Library for MSP430
MSPMATHLIB MSPMathLib is an accelerated floating point math library for MSP430™ MCUs that delivers up to 26x faster computation for the most commonly used math functions. The library seamlessly integrates with projects to replace floating point math functions such as sin, cos, tan, log, exp and sqrt (...)
Features
  • Up to 26x higher performance when executing floating point scalar math functions
  • Remains in low power modes longer due to the increased performance
  • Free and easy to use –  now integrated in CCS and IAR
IDE, CONFIGURATION, COMPILER OR DEBUGGER Download
Code Composer Studio™ Integrated Development Environment for MSP Microcontrollers
CCSTUDIO-MSP

Code Composer Studio is an integrated development environment (IDE) that supports TI's Microcontroller and Embedded Processors portfolio. Code Composer Studio comprises a suite of tools used to develop and debug embedded applications. It includes an optimizing C/C++ compiler, source code editor (...)

IDE, CONFIGURATION, COMPILER OR DEBUGGER Download
EnergyTrace Technology
ENERGYTRACE EnergyTrace™ software for MSP430™ MCUs, MSP432™ MCUs, CC13xx wireless MCUs and CC26xx wireless MCUs is an energy-based code analysis tool that measures and displays the energy profile of an application and helps optimize it for ultra-low-power consumption.

As most developers know, it is difficult to (...)

Features
  • Current measurement is enabled for all MSP430 MCUs, MSP432 MCUs and connectivity devices
  • Tracing of CPU states is available on selected MSP430 MCUs, MSP432 MCUs, CC13x2 wireless MCUs and CC26x2 wireless MCUs 
  • Tracing of peripheral states is also available on selected MSP430 MCUs, CC13x2 (...)
IDE, CONFIGURATION, COMPILER OR DEBUGGER Download
IAR Embedded Workbench
Provided by IAR Systems IAR Embedded Workbench includes the IAR C/C++ compiler and C-SPY debugger for building and debugging embedded applications for your selected target microcontroller. The IAR compiler generates highly optimized code for your application, and the debugger is a fully integrated debugger for source and (...)
SOFTWARE PROGRAMMING TOOL Download
UniFlash stand-alone flash tool for microcontrollers, Sitara™; processors and SimpleLink™
UNIFLASH Supported devices: CC13xx, CC25xx, CC26xx, CC3x20, CC3x30, CC3x35, Tiva, C2000, MSP43x, Hercules, PGA9xx, IWR12xx, IWR14xx, IWR16xx, IWR18xx , IWR68xx, AWR12xx, AWR14xx, AWR16xx, AWR18xx.  Command line only: AM335x, AM437x, AM571x, AM572x, AM574x, AM65XX, K2G

CCS Uniflash is a standalone tool used to (...)

Design tools & simulation

CAD/CAE SYMBOL Download
SLAC060E.ZIP (97 KB)

CAD/CAE symbols

Package Pins Download
BGA MICROSTAR JUNIOR (ZQE) 80 View options
VQFN (RGC) 64 View options

Ordering & quality

Information included:
  • RoHS
  • REACH
  • Device marking
  • Lead finish/Ball material
  • MSL rating/Peak reflow
  • MTBF/FIT estimates
  • Material content
  • Qualification summary
  • Ongoing reliability monitoring

Support & training

TI E2E™ forums with technical support from TI engineers

Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.

If you have questions about quality, packaging or ordering TI products, see TI support. ​​​​​​​​​​​​​​

Videos

Related videos