Top
Polyphase Metering SoC with 6 Sigma-Delta ADCs, LCD, Real-Time Clock, 256KB Flash, 32KB RAM

MSP430F67671

ACTIVE

Product details

Parameters

Features Advanced sensing, LCD, Real-time clock Non-volatile memory (kB) 256 RAM (KB) 32 ADC 24-bit Sigma Delta ADC: channels (#) 6 GPIO pins (#) 90 I2C 2 SPI 6 UART 4 Comparator channels (#) 0 Timers - 16-bit 4 Bootloader (BSL) UART Special I/O Operating temperature range (C) -40 to 85 Rating Catalog open-in-new Find other MSP430 ultra-low-power MCUs

Package | Pins | Size

LQFP (PEU) 128 352 mm² 22 x 16 LQFP (PZ) 100 256 mm² 16 x 16 open-in-new Find other MSP430 ultra-low-power MCUs

Features

  • Accuracy < 0.1% Over 2000:1 Dynamic Range for Phase Current
  • Meets or Exceeds ANSI C12.20 and IEC 62053 Standards
  • Support for Multiple Sensors Such as Current Transformers, Rogowski Coils, or Shunts
  • Power Measurement for up to Three Phases Plus Neutral
  • Dedicated Pulse Output Pins for Active and Reactive Energy for Calibration
  • Four-Quadrant Measurement per Phase or Cumulative
  • Exact Phase Angle Measurements
  • Digital Phase Correction for Current Transformers
  • Temperature Compensated Energy Measurements
  • 40-Hz to 70-Hz Line Frequency Range Using Single Calibration
  • Flexible Power Supply Options With Automatic Switching
  • Display Operates at Very Low Power During AC Mains Failure: 3 µA in LPM3
  • LCD Driver With Contrast Control for up to 320 Segments
  • Password-Protected Real-Time Clock (RTC) With Crystal Offset Calibration and Temperature Compensation
  • Integrated Security Modules to Support Anti-Tamper
  • Multiple Communication Interfaces for Smart Meter Implementations
  • High-Performance 25-MHz CPU With 32-Bit Multiplier
  • Wide Input Supply Voltage Range:
    3.6 V Down to 1.8 V
  • Ultra-Low Power Consumption During Energy Measurement
    • 2.9 mW at 10-MHz Operation (3 V)
  • Multiple Low-Power Modes
    • Standby Mode (LPM3): 2.1 µA at 3 V,
      Wake up in Less Than 5 µs
    • RTC Mode (LPM3.5): 0.34 µA at 3 V
    • Shutdown Mode (LPM4.5): 0.18 µA at 3 V
  • Up to 512KB of Single-Cycle Flash
  • Up to 32KB of RAM With Single-Cycle Access
  • Up to Seven Independent 24-Bit Sigma-Delta ADCs With Differential Inputs and Variable Gain
  • System 10-Bit 200-ksps ADC
    • Six Channels Plus Supply and Temperature Sensor Measurement
  • Six Enhanced Communications Ports
    • Configurable Among Four UART, Six SPI, and Two I²C Interfaces
  • Four 16-Bit Timers With Nine Total Capture/Compare Registers
  • 128-Pin LQFP (PEU) Package With 90 I/O Pins
  • 100-Pin LQFP (PZ) Package With 62 I/O Pins
  • Industrial Temperature Range of –40°C to 85°C
  • 3-Phase Electronic Watt-Hour Meter Development Tool (Also See Tools and Software)

All trademarks are the property of their respective owners.

open-in-new Find other MSP430 ultra-low-power MCUs

Description

The TI MSP430F677x1 family of polyphase metering SoCs are powerful highly integrated solutions for revenue meters that offer accuracy and low system cost with few external components. The F677x1 family of devices uses the low-power MSP430 CPU with a 32-bit multiplier to perform all energy calculations, metering applications such as tariff rate management, and communications with AMR and AMI modules.

The F677x1 devices feature TI’s 24-bit sigma-delta converter technology, which provides better than 0.1% accuracy. Family members include up to 512KB of flash, 32KB of RAM, and an LCD controller with support for up to 320 segments.

The ultra-low-power nature of the F677x1 devices means that the system power supply can be minimized to reduce overall cost. Lowest standby power means that backup energy storage can be minimized and critical data retained longer in case of a mains power failure.

The F677x1 family of devices executes the TI energy measurement software library, which calculates all relevant energy and power results. The energy measurement software library is available with the F677x1 devices at no cost. Industry standard development tools and hardware platforms are available to speed development of meters that meet all of the ANSI and IEC standards globally.

For complete module descriptions, see the MSP430F5xx and MSP430F6xx Family User’s Guide.

open-in-new Find other MSP430 ultra-low-power MCUs
Download
Similar products you might be interested in
open-in-new Compare products
Same functionality and pinout but is not an equivalent to the compared device:
MSP430F67671A ACTIVE Polyphase Metering SoC with 6 Sigma-Delta ADCs, LCD, Real-Time Clock, 256KB Flash, 32KB RAM This product has the same memory, peripherals including the sigma-delta ADC(s), and pin-out configuration while incorporating several errata improvements.

Technical documentation

= Top documentation for this product selected by TI
No results found. Please clear your search and try again. View all 21
Type Title Date
* Datasheet MSP430F677x1, MSP430F676x1, MSP430F674x1 Polyphase Metering SoCs datasheet (Rev. D) Sep. 28, 2018
* Errata MSP430F67671 Device Erratasheet (Rev. AB) Apr. 24, 2019
* User guide MSP430x5xx and MSP430x6xx Family User's Guide (Rev. Q) Aug. 17, 2018
User guide MSP430 MCUs Development Guide Book Oct. 09, 2020
Application note Answers to Common Sigma-Delta ADC Questions on MSP MCUs Aug. 11, 2020
Application note Differences Between MSP430F67xx and MSP430F67xxA Devices (Rev. A) Jan. 13, 2020
Application note MSP430 System-Level ESD Considerations (Rev. A) Jan. 13, 2020
Application note MSP430 System ESD Troubleshooting Guide Dec. 13, 2019
Application note ESD Diode Current Specification (Rev. A) Jul. 10, 2019
Application note MSP430 32-kHz Crystal Oscillators (Rev. D) Jul. 18, 2017
Application note How delta-sigma ADCs work, Part 1 (Rev. A) Sep. 19, 2016
Technical articles “Touching” the smart grid infrastructure space with capacitive sensing technology Mar. 31, 2016
Technical articles Don’t miss out on the top training videos of 2015 Dec. 16, 2015
Application note MSP Code Protection Features Dec. 07, 2015
Application note Designing With MSP430™ MCUs and Segment LCDs (Rev. A) Jul. 20, 2015
Technical articles How fast is your 32-bit MCU? Jul. 15, 2015
Technical articles Lose power, not data with new FRAM microcontrollers May 20, 2015
Application note MSP430 Advanced Power Optimizations: ULP Advisor SW and EnergyTrace Technology Jun. 09, 2014
Application note Using TI’s DLMS COSEM Library Nov. 12, 2013
Application note A Glossary of Analog-to-Digital Specifications and Performance Characteristics (Rev. B) Oct. 09, 2011
Application note Design of Differential Filters for High-Speed Signal Chains (Rev. B) Apr. 30, 2010

Design & development

For additional terms or required resources, click any title below to view the detail page where available.

Hardware development

EVALUATION BOARD Download
275
Description

This EVM430-F6779 is a three-phase electricity meter evaluation module based on the MSP430F6779 device. The E-meter has inputs for three voltages and three currents, as well as an additional connection to setup anti-tampering. It allows a customer to test the new (...)

Features
  • Run real-time electricity metering applications
  • Metrology software provided
  • Connects to any test system or AC voltage
  • Capacitive and isolated power supplies present
  • Easy viewing of results and calibration via RS-232
  • 160 segment LCD display
  • RF connectors for AMR/AMI support
  • 32kHz RTC support (header (...)
DEVELOPMENT KIT Download
149
Description

The MSP-TS430PEU128 is a standalone 128-pin ZIF socket target board used to program and debug the MSP430 MCU in-system through the JTAG interface or the Spy Bi-Wire (2-wire JTAG) protocol.

Device Support: The MSP-TS430PEU128 development board supports MSP430F677x, MSP430F676x, MSP430F674x (...)

Features
  • Development board (MSP-TS430PEU128) with a 128-pin ZIF socket fitting MSP430 derivatives in 128-pin QFP (PEU) packages includes an LED indicator, JTAG adapter, and header pin-outs for prototyping
  • Supports all debugging interfaces using a standard 14-pin JTAG header such as the MSP-FET430UIF.
HARDWARE PROGRAMMING TOOL Download
115
Description

The MSP-FET is a powerful emulation development tool – often called a debug probe – which allows users to quickly begin development on MSP low-power microcontrollers (MCU).

It supports programming and real-time debugging over both JTAG and SBW interfaces. Furthermore, the MSP-FET also provides a (...)

Features
  • USB debugging interface to connect any MSP430 MCU to a computer for real-time, in-system programming and debugging
  • Enables EnergyTrace™ technology for energy measurement and debugging on all MSP430 and MSP432 devices in the Code Composer Studio and IAR Embedded Workbench development environments
  • (...)
HARDWARE PROGRAMMING TOOL Download
Description

The MSP Gang Programmer (MSP-GANG) is a MSP430™/MSP432™ device programmer that can program up to eight identical MSP430/MSP432 Flash or FRAM devices at the same time. It connects to a host PC using a standard RS-232 or USB connection and provides flexible programming options that allow (...)

Features
  • Quickly and reliably program Flash or FRAM-based MSP devices via RS-232 or USB interface
  • Several programming modes:
    • Interactive Mode – Programming while connected to PC using the MSP GANG Programmer GUI
    • Program from Image – An image can be stored, which contains configuration options and code (...)

Software development

SOFTWARE DEVELOPMENT KIT (SDK) Download
MSP430Ware for MSP Microcontrollers
MSPWARE MSP430Ware is a collection of resources that help users to effectively create and build MSP430 code. These resources support ALL MSP430 microcontrollers (MCUs). As one user mentioned, “It’s essentially everything developers need to become MSP430 microcontroller experts!”

This complete collection of (...)

Features
  • Collection of MSP design resources
  • Available within CCS, as a standalone executable, or as part of TI’s new Cloud-based tools
  • Auto-updates through the web
  • Sleek & intuitive GUI for browsing content
  • Features the MSP Driver Library
  • Automatic filtering of content using a unique 2-pane view
DRIVER OR LIBRARY Download
Digital Signal Processing (DSP) Library for MSP430 Microcontrollers
MSP-DSPLIB The TI MSP430™ Digital Signal Processing library is a set of optimized functions to perform common signal processing operations for MSP430 microcontrollers. These functions are used in applications where processing-intensive transforms are done in real-time for minimal energy and with very (...)
DRIVER OR LIBRARY Download
MSP Graphics Library
MSP-GRLIB The MSP Graphics Library is a royalty-free set of graphics primitives for displaying images or creating graphical user interfaces (GUIs) on MSP430 and MSP432 microcontroller-based boards that use a graphical display. The graphics library consists of two functional layers: 1) the display driver layer (...)
Features
  • Free license and royalty-free use
  • Simplify and accelerate development of applications
  • Easy-to-maintain code
DRIVER OR LIBRARY Download
Fixed Point Math Library for MSP
MSP-IQMATHLIB The Texas Instruments® MSP IQmath and Qmath Libraries are a collection of highly optimized and high-precision mathematical functions for C programmers to seamlessly port a floating-point algorithm into fixed-point code on MSP430 and MSP432 devices. These routines are typically used in (...)
Features
  • Optimized fixed point functions - reduce development time and enable developers to focus on optimizing application code
  • Up to 100x higher performance when executing common fixed point scalar math functions in CCS – this means the MSP microcontroller can remain in low power modes longer than (...)
DRIVER OR LIBRARY Download
Bootloader (BSL) for MSP low-power microcontrollers
MSPBSL The bootloader (BSL) on MSP430™ microcontrollers (MCUs) lets users communicate with embedded memory in the MSP MCUs during the prototyping phase, final production, and in service. This is done through standard interfaces such as UART, I2C, SPI, and USB. Both the programmable memory (...)
DRIVER OR LIBRARY Download
Floating Point Math Library for MSP430
MSPMATHLIB MSPMathLib is an accelerated floating point math library for MSP430™ MCUs that delivers up to 26x faster computation for the most commonly used math functions. The library seamlessly integrates with projects to replace floating point math functions such as sin, cos, tan, log, exp and sqrt (...)
Features
  • Up to 26x higher performance when executing floating point scalar math functions
  • Remains in low power modes longer due to the increased performance
  • Free and easy to use –  now integrated in CCS and IAR
GUI FOR EVALUATION MODULE (EVM) Download
Energy Measurement Design Center for MSP430 MCUs
MSP-EM-DESIGN-CENTER The Energy Measurement Design Center is a rapid development tool that enables energy measurement using TI MSP430i20xx and MSP430F67xx flash-based microcontrollers (MCUs). It includes a graphical user interface (GUI), documentation, software library and examples that can simplify development and (...)
Features
  • Supported measurements:
    • Voltage and Current
      • RMS
      • Peak
    • Power and Energy
      • Active
      • Reactive
      • Apparent
    • Power Factor
    • Frequency
  • Supported current sensors:
    • Shunt
    • Current transformer (CT)
    • Rogowski coil (RC)
  • View estimated CPU bandwidth (library only) for supported system configurations
  • Generate source code projects for Code (...)
IDE, CONFIGURATION, COMPILER OR DEBUGGER Download
Code Composer Studio™ Integrated Development Environment for MSP Microcontrollers
CCSTUDIO-MSP

Code Composer Studio is an integrated development environment (IDE) that supports TI's Microcontroller and Embedded Processors portfolio. Code Composer Studio comprises a suite of tools used to develop and debug embedded applications. It includes an optimizing C/C++ compiler, source code editor (...)

IDE, CONFIGURATION, COMPILER OR DEBUGGER Download
EnergyTrace Technology
ENERGYTRACE EnergyTrace™ software for MSP430™ MCUs, MSP432™ MCUs, CC13xx wireless MCUs and CC26xx wireless MCUs is an energy-based code analysis tool that measures and displays the energy profile of an application and helps optimize it for ultra-low-power consumption.

As most developers know, it is difficult to (...)

Features
  • Current measurement is enabled for all MSP430 MCUs, MSP432 MCUs and connectivity devices
  • Tracing of CPU states is available on selected MSP430 MCUs, MSP432 MCUs, CC13x2 wireless MCUs and CC26x2 wireless MCUs 
  • Tracing of peripheral states is also available on selected MSP430 MCUs, CC13x2 (...)
IDE, CONFIGURATION, COMPILER OR DEBUGGER Download
IAR Embedded Workbench
Provided by IAR Systems IAR Embedded Workbench includes the IAR C/C++ compiler and C-SPY debugger for building and debugging embedded applications for your selected target microcontroller. The IAR compiler generates highly optimized code for your application, and the debugger is a fully integrated debugger for source and (...)
SOFTWARE PROGRAMMING TOOL Download
UniFlash stand-alone flash tool for microcontrollers, Sitara™; processors and SimpleLink™
UNIFLASH Supported devices: CC13xx, CC25xx, CC26xx, CC3x20, CC3x30, CC3x35, Tiva, C2000, MSP43x, Hercules, PGA9xx, IWR12xx, IWR14xx, IWR16xx, IWR18xx , IWR68xx, AWR12xx, AWR14xx, AWR16xx, AWR18xx.  Command line only: AM335x, AM437x, AM571x, AM572x, AM574x, AM65XX, K2G

CCS Uniflash is a standalone tool used to (...)

SUPPORT SOFTWARE Download
SLAC561G.ZIP (242 KB)

CAD/CAE symbols

Package Pins Download
LQFP (PEU) 128 View options
LQFP (PZ) 100 View options

Ordering & quality

Information included:
  • RoHS
  • REACH
  • Device marking
  • Lead finish/Ball material
  • MSL rating/Peak reflow
  • MTBF/FIT estimates
  • Material content
  • Qualification summary
  • Ongoing reliability monitoring

Support & training

TI E2E™ forums with technical support from TI engineers

Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.

If you have questions about quality, packaging or ordering TI products, see TI support. ​​​​​​​​​​​​​​

Videos

Related videos