Home Energiemanagement Leistungsschutzschalter und Controller eFuses (integrierte Hot-Swaps)
NEU

LM7311

VORSCHAU

Produktdetails

Vabsmax_cont (V) 28 Vin (max) (V) 23 Vin (min) (V) 3.5 Current limit (max) (A) 5 Features Adjustable soft start, Current monitoring, Fault output, Overvoltage protection, Reverse current blocking, Short-circuit protection, Surge protection, Thermal shutdown, adjustable UVLO Overcurrent response Short-circuit protection Fault response Auto Retry, Latch-off Ron (typ) (mΩ) 33 Overvoltage response Cut-off Rating Catalog Device type eFuses and hot swap controllers Operating temperature range (°C) -40 to 125
Vabsmax_cont (V) 28 Vin (max) (V) 23 Vin (min) (V) 3.5 Current limit (max) (A) 5 Features Adjustable soft start, Current monitoring, Fault output, Overvoltage protection, Reverse current blocking, Short-circuit protection, Surge protection, Thermal shutdown, adjustable UVLO Overcurrent response Short-circuit protection Fault response Auto Retry, Latch-off Ron (typ) (mΩ) 33 Overvoltage response Cut-off Rating Catalog Device type eFuses and hot swap controllers Operating temperature range (°C) -40 to 125
WSON (DRR) 12 9 mm² (3 mm × 3 mm)
  • Wide operating input voltage range: 3.5V to 23V
    • 28V absolute maximum
    • Output negative voltage support up to -1V
  • Integrated back-to-back FETs with low ON-resistance: RON = 33mΩ (typical)
  • 5A continuous current
  • 15A peak current for 10ms with 2% duty cycle
  • Active high enable input with adjustable undervoltage lockout (UVLO)
  • Ideal diode operation with true reverse-current blocking (RCB)
  • Fixed overvoltage (OVLO) protection with debounce time
  • Analog load current monitor output (IMON)
    • Current range: 1A to 5.5A
    • Accuracy: ±3% (IOUT≥3A)
  • Short circuit protection at startup and steady state
  • Adjustable output slew rate control (dVdT)
  • Overtemperature protection
  • IEC61000-4-2: ±8kV direct contact and ±15kV air discharge on VIN and VOUT
  • IEC61000-4-5: 35V on VIN, no cap
  • Digital output: fault indication (FLT)
  • Small footprint: DFN 3mm × 3mm
  • Wide operating input voltage range: 3.5V to 23V
    • 28V absolute maximum
    • Output negative voltage support up to -1V
  • Integrated back-to-back FETs with low ON-resistance: RON = 33mΩ (typical)
  • 5A continuous current
  • 15A peak current for 10ms with 2% duty cycle
  • Active high enable input with adjustable undervoltage lockout (UVLO)
  • Ideal diode operation with true reverse-current blocking (RCB)
  • Fixed overvoltage (OVLO) protection with debounce time
  • Analog load current monitor output (IMON)
    • Current range: 1A to 5.5A
    • Accuracy: ±3% (IOUT≥3A)
  • Short circuit protection at startup and steady state
  • Adjustable output slew rate control (dVdT)
  • Overtemperature protection
  • IEC61000-4-2: ±8kV direct contact and ±15kV air discharge on VIN and VOUT
  • IEC61000-4-5: 35V on VIN, no cap
  • Digital output: fault indication (FLT)
  • Small footprint: DFN 3mm × 3mm

The LM7311x family is a highly integrated, circuit-protection and power-management device in a small package. The devices provide multiple protection modes that use few external components and are a robust defense against overloads, short-circuits, voltage surges and excessive inrush current. With integrated back-to-back FETs, reverse-current flow from output to input is blocked at all times, making the devices an excellent choice for ORing applications, as well as systems that need load side energy holdup storage if input power supply fails. The devices use a linear ORing based scheme to maintain almost zero DC reverse current and emulate ideal diode behavior with minimum forward voltage drop and power dissipation.

Output slew rate and inrush current can be adjusted using one external capacitor. Loads are protected from input overvoltage conditions by cutting off the output if input exceeds the fixed overvoltage threshold.

The device provides an accurate sense of the output load current on the analog current monitor pin.

The device provides robust protection from overvoltages and short-circuit protection in start-up (ISFT) and Steady state (IFFT). The negative 1V DC support on VOUT provides additional robustness during inductive negative transients at VOUT.

The devices are available in a 3mm × 3mm, for improved thermal performance and reduced system footprint.

The devices are characterized for operation over a junction temperature range from –40°C to +125°C.

The LM7311x family is a highly integrated, circuit-protection and power-management device in a small package. The devices provide multiple protection modes that use few external components and are a robust defense against overloads, short-circuits, voltage surges and excessive inrush current. With integrated back-to-back FETs, reverse-current flow from output to input is blocked at all times, making the devices an excellent choice for ORing applications, as well as systems that need load side energy holdup storage if input power supply fails. The devices use a linear ORing based scheme to maintain almost zero DC reverse current and emulate ideal diode behavior with minimum forward voltage drop and power dissipation.

Output slew rate and inrush current can be adjusted using one external capacitor. Loads are protected from input overvoltage conditions by cutting off the output if input exceeds the fixed overvoltage threshold.

The device provides an accurate sense of the output load current on the analog current monitor pin.

The device provides robust protection from overvoltages and short-circuit protection in start-up (ISFT) and Steady state (IFFT). The negative 1V DC support on VOUT provides additional robustness during inductive negative transients at VOUT.

The devices are available in a 3mm × 3mm, for improved thermal performance and reduced system footprint.

The devices are characterized for operation over a junction temperature range from –40°C to +125°C.

Herunterladen Video mit Transkript ansehen Video

Technische Dokumentation

Keine Ergebnisse gefunden. Bitte geben Sie einen anderen Begriff ein und versuchen Sie es erneut.
Alle anzeigen 1
Top-Dokumentation Typ Titel Format-Optionen Neueste englische Version herunterladen Datum
* Datenblatt LM7311 3.5V–23V, 33mΩ, 5A eFuse With True Reverse Current Blocking datasheet (Rev. A) PDF | HTML 10.11.2026

Design und Entwicklung

Weitere Bedingungen oder erforderliche Ressourcen enthält gegebenenfalls die Detailseite, die Sie durch Klicken auf einen der unten stehenden Titel erreichen.

Evaluierungsplatine

LM7320-30EVM — Evaluierungsmodul für LM7311, LM7320 und LM7330

The LM7320-30EVM evaluates the performance of the LM7311, LM7320, and LM7330 eFuse devices. The LM7320-30EVM comes with LM7311 and LM7330 eFuse for evaluation of 12V (typical) and 5A (steady state) designs.

Evaluate the LM7320 by replacing LM7311 on the U1 slot.

Benutzerhandbuch: PDF | HTML
Unterstützte Produkte und Hardware
Vorrätig
Limit:
??asset.out-of-stock-ti_de_DE??
Nicht verfügbar
Simulationsmodell

LM7311 PSpice Transient Model

SLVMFF1.ZIP (161940 KB) - PSpice-Modell
Unterstützte Produkte und Hardware
Berechnungstool

LM7311-CALC — LM7311 Design Calculator

The design calculator allows customer to size the external peripheral components while designing with LM7311 eFuse
Unterstützte Produkte und Hardware
Gehäuse Pins CAD-Symbole, Footprints und 3D-Modelle
WSON (DRR) 12 Ultra Librarian

Bestellen & Qualität

Empfohlene Produkte können Parameter, Evaluierungsmodule oder Referenzdesigns zu diesem TI-Produkt beinhalten.

Support und Schulungen

TI E2E™-Foren mit technischem Support von TI-Ingenieuren

Inhalte werden ohne Gewähr von TI und der Community bereitgestellt. Sie stellen keine Spezifikationen von TI dar. Siehe Nutzungsbedingungen.

Bei Fragen zu den Themen Qualität, Gehäuse oder Bestellung von TI-Produkten siehe TI-Support. ​​​​​​​​​​​​​​

Videos