Inicio Administración de potencia Reguladores conmutados CC/CC Controladores de CC/CC
Inicio
Administración de potencia
Reguladores conmutados CC/CC
Controladores de CC/CC
NUEVO

LM51251A-Q1

ACTIVO

Controlador boost bifásico automotriz de 2.2 MHz con VIN de 42 V y seguimiento de VOUT e I2C

Haga su pedido ahora
Hoja de datos

LM51251A-Q1

ACTIVO
Hoja de datos Haga su pedido ahora

Detalles del producto

Rating Automotive Topology Boost Controller Vin (max) (V) 45 Vin (min) (V) 2.5 Vout (max) (V) 60 Vout (min) (V) 6 Control mode current mode control Features Adjustable current limit, Adjustable soft start, Adjustable switching frequency, Analog current monitor, Automatic Light Load Management, Automotive load dump, Bypass Mode, Chip-enable control pin, Cycle-by-cycle overcurrent protection, External Sync, Fixed PWM Mode, I2C interface, Multiphase, Overcurrent protection with adjustable delay, Power good, Programmable dead time, Spread Spectrum, Tracking EMI features Frequency Dithering, Spread Spectrum Duty cycle (max) (%) 99.2 Iq (typ) (A) 0.00025 TI functional safety category Functional Safety-Capable Operating temperature range (°C) -40 to 150
Rating Automotive Topology Boost Controller Vin (max) (V) 45 Vin (min) (V) 2.5 Vout (max) (V) 60 Vout (min) (V) 6 Control mode current mode control Features Adjustable current limit, Adjustable soft start, Adjustable switching frequency, Analog current monitor, Automatic Light Load Management, Automotive load dump, Bypass Mode, Chip-enable control pin, Cycle-by-cycle overcurrent protection, External Sync, Fixed PWM Mode, I2C interface, Multiphase, Overcurrent protection with adjustable delay, Power good, Programmable dead time, Spread Spectrum, Tracking EMI features Frequency Dithering, Spread Spectrum Duty cycle (max) (%) 99.2 Iq (typ) (A) 0.00025 TI functional safety category Functional Safety-Capable Operating temperature range (°C) -40 to 150
VQFN (RHB) 32 25 mm² 5 x 5
  • AEC-Q100 qualified for automotive applications
    • Temperature grade 1: TA = –40°C to +125°C
  • Functional Safety-Capable
  • Input voltage 4.5V to 42V
    • Minimum 2.5V for V(BIAS) ≥ 4.5V or VOUT ≥ 6V
  • Output Voltage 6V to 60V
    • Adjustable by resistor or by I2C in 1V steps
    • Adjustable slew rate when programmed by I2C
    • 2% accuracy, internal feedback resistors
    • Bypass operation for VI > VOUT
    • Dynamic output voltage tracking
      • Digital PWM tracking (DTRK)
      • Analog tracking (ATRK)
    • Overvoltage protection (64V, 50V, 35V, 28.5V)
  • Low shutdown IQ of 2µA and operating IQ of 1.4mA
  • Stacking with interleaved multiphase operation
    • Up to 4-phases without external clock
  • Switching frequency from 100kHz to 2.2MHz
    • Synchronization to external clock (SYNCIN)
    • Dynamically selectable switching modes (FPWM, diode emulation)
    • Spread spectrum (DRSS)
  • I2C Interface with 8 selectable addresses
  • I2C programmable dead time (14ns to 200ns)
  • Current sense resistor or DCR sensing
  • Average inductor current monitor
  • Average input current limit
    • Programmable current limit
    • Selectable delay time
  • nFAULT indicator
  • Programmable VI undervoltage lockout (UVLO)
  • Lead-less VQFN-32 package with wettable flanks
  • AEC-Q100 qualified for automotive applications
    • Temperature grade 1: TA = –40°C to +125°C
  • Functional Safety-Capable
  • Input voltage 4.5V to 42V
    • Minimum 2.5V for V(BIAS) ≥ 4.5V or VOUT ≥ 6V
  • Output Voltage 6V to 60V
    • Adjustable by resistor or by I2C in 1V steps
    • Adjustable slew rate when programmed by I2C
    • 2% accuracy, internal feedback resistors
    • Bypass operation for VI > VOUT
    • Dynamic output voltage tracking
      • Digital PWM tracking (DTRK)
      • Analog tracking (ATRK)
    • Overvoltage protection (64V, 50V, 35V, 28.5V)
  • Low shutdown IQ of 2µA and operating IQ of 1.4mA
  • Stacking with interleaved multiphase operation
    • Up to 4-phases without external clock
  • Switching frequency from 100kHz to 2.2MHz
    • Synchronization to external clock (SYNCIN)
    • Dynamically selectable switching modes (FPWM, diode emulation)
    • Spread spectrum (DRSS)
  • I2C Interface with 8 selectable addresses
  • I2C programmable dead time (14ns to 200ns)
  • Current sense resistor or DCR sensing
  • Average inductor current monitor
  • Average input current limit
    • Programmable current limit
    • Selectable delay time
  • nFAULT indicator
  • Programmable VI undervoltage lockout (UVLO)
  • Lead-less VQFN-32 package with wettable flanks

The LM51251A-Q1 is a stackable, dual-phase, synchronous boost controller with I2C interface. The device provides a regulated output voltage for lower or equal input voltage also supporting VI to VOUT bypass mode to save power. Stack two devices with or without external clock.

Dynamically program VOUT using the analog or digital ATRK/DTRK function or I2C programming. VI is supported down to 2.5V after start-up as the internal VCC supply is automatically switched from VBIAS to VOUT for VBIAS < 4.5V. The fixed switching frequency is set between 100kHz and 2.2MHz through a resistor on the RT pin or the SYNCIN clock. The switching modes FPWM or diode emulation can be changed during operation.

The implemented protections peak current limit, average input current limit, average inductor current monitor, over and undervoltage protection, and the thermal shutdown protect the device and the application.

The LM51251A-Q1 is a stackable, dual-phase, synchronous boost controller with I2C interface. The device provides a regulated output voltage for lower or equal input voltage also supporting VI to VOUT bypass mode to save power. Stack two devices with or without external clock.

Dynamically program VOUT using the analog or digital ATRK/DTRK function or I2C programming. VI is supported down to 2.5V after start-up as the internal VCC supply is automatically switched from VBIAS to VOUT for VBIAS < 4.5V. The fixed switching frequency is set between 100kHz and 2.2MHz through a resistor on the RT pin or the SYNCIN clock. The switching modes FPWM or diode emulation can be changed during operation.

The implemented protections peak current limit, average input current limit, average inductor current monitor, over and undervoltage protection, and the thermal shutdown protect the device and the application.
filter Buscar otro/a Controladores de CC/CC
Descargar Ver vídeo con transcripción Video

Documentación técnica

star =Principal documentación para este producto seleccionada por TI
No se encontraron resultados. Borre su búsqueda y vuelva a intentarlo.
Ver todo 4
Documentación principal Tipo Título Opciones de formato Fecha
* Data sheet LM5125 1A -Q1, Wide-VIN, Dual-Phase, Boost Controller With VOUT Tracking and I2C datasheet PDF | HTML 26 nov 2025
Application note Optimizing the High Side Switch Gate Ringing PDF | HTML 16 abr 2026
Application note Asynchronous Operation of LM5125x Boost Controller PDF | HTML 02 dic 2025
Functional safety information LM5125-Q1, LM5125A-Q1, and LM51251A-Q1 Functional Safety FIT Rate, FMD and Pin FMA (Rev. A) PDF | HTML 09 sep 2025

Diseño y desarrollo

Para conocer los términos adicionales o los recursos necesarios, haga clic en cualquier título de abajo para ver la página de detalles cuando esté disponible.

Placa de evaluación

LM5125AEVM-BST — Módulo de evaluación LM5125AEVM-BST

El módulo de evaluación LM5125AEVM-BST muestra las características y el rendimiento del controlador boost bifásico sincrónico de tensión de entrada amplia LM5125A-Q1. Este EVM está diseñado para facilitar la configuración, lo que permite al usuario evaluar diferentes condiciones en el módulo. El (...)
Guía del usuario: PDF | HTML
No disponible en TI.com
Herramienta de cálculo

LM5125-CALC — LM5125(A) quick start calculator

LM5125(A) quick start calculator helps on design of the power stage, component selection and loop compensation.
Productos y hardware compatibles

Productos y hardware compatibles
Descargar
Herramienta de diseño

LM51251A-GUI — GUI for LM51251A

GUI for LM51251A
Productos y hardware compatibles

Productos y hardware compatibles
Iniciar Opciones de descarga
Encapsulado Pines Símbolos CAD, huellas y modelos 3D
VQFN (RHB) 32 Ultra Librarian
Se aplican los Términos y condiciones estándar de TI para los elementos de evaluación.

Pedidos y calidad

Información incluida:
  • RoHS
  • REACH
  • Marcado del dispositivo
  • Acabado de plomo/material de la bola
  • Clasificación de nivel de sensibilidad a la humedad (MSL)/reflujo máximo
  • Estimaciones de tiempo medio entre fallas (MTBF)/fallas en el tiempo (FIT)
  • Contenido del material
  • Resumen de calificaciones
  • Monitoreo continuo de confiabilidad
Información incluida:
  • Lugar de fabricación
  • Lugar de ensamblaje

Los productos recomendados pueden tener parámetros, módulos de evaluación o diseños de referencia relacionados con este producto de TI.

Soporte y capacitación

Foros de TI E2E™ con asistencia técnica de los ingenieros de TI

Ver todos los temas del foro en inglés

El contenido lo proporcionan “tal como está” TI y los colaboradores de la comunidad y no constituye especificaciones de TI. Consulte los términos de uso.

Si tiene alguna pregunta sobre calidad, encapsulados o pedido de productos de TI, consulte el servicio de asistencia de TI. ​​​​​​​​​​​​​​

Videos